What did you use your Sak on today?

[jerseydevil]

Tonight at a meeting someone needed a pair of scissors.  I went to get my Rambler out of my pocket and but a lady says, "Here you go" and hands over a Classic to the person in need.  This lady who had the Classic was the same one who two weeks ago commented how useful my Rambler looked, and that she needed to get one!    So what did I use my SAK on today?  Nothing, because my enabling ways bore fruit. 




See Lynn?  It's not just you I've infected. 

[Monrogue]

Nice work indeed Tom

[Lynn LeFey]

See Lynn?  It's not just you I've infected. 

And you're doing a fine job, sir! 

[toddwalla]

The main blade of my pioneer opened the mail, a stubborn box of pasta, and sliced open a stuffed animal so as to remove the infernal noise making component. The can opener opened some pasta sauce to accompany the aforementioned pasta (the work can opener has gone on the lam) and did double duty by removing the screws that separated me from the batteries in that damn infernal toy! All in a days work

[kirk13]

Used the tooth pick from my DofE to spear olives

[dks]

used my pruners pruning blade to make a robot helmet out of a box

[SAK Guy]

used my pruners pruning blade to make a robot helmet out of a box

 

[zoidberg]

I used one SAK to help clean another SAK.

[hiraethus]

Cut some cake with my Pioneer

[MadPlumbarian]

Cut some cake with my Pioneer

At least you didn't use it to cut the cheese, sorry I just had to say it!
JR

[kirk13]

Used my new Pioneer and my Wenger Handyman to make up new gaskets and fit new seals to my Airgun pump

[SAK Guy]

Used my new Pioneer and my Wenger Handyman to make up new gaskets and fit new seals to my Airgun pump

Cool!

[TazzieRob]

Used the Cadet Can Opener SD to install a new TV base after opening the plastic bag for the screws with the knife blade.
Can opener blade just cleared the plastic enough to allow full rotation.

[bigz89]

Used my EVO16 to cut PEX pipe for a plumbing repair and used screwdriver to pry off some small moldings to get at leak.

[zoidberg]

I used a Spirit and CT41 to work on a Wingman mod.

[zoidberg]

And the SI to open the beers.

[HarleyXJGuy]

And the SI to open the beers.

Doesn't the CT 41 have everything the SI does?

Why carry both other then cause I like too?

[shark_za]

93mm bottle opener is just that little bit nicer to use.

[HarleyXJGuy]

93mm bottle opener is just that little bit nicer to use.

Did not know they were different bottle openers in the Alox.

[zoidberg]

And the SI to open the beers.

Doesn't the CT 41 have everything the SI does?

Why carry both other then cause I like too?

Other than what you have to do isn't everything else cause you like too?

I was carrying the SI. Then I needed the CT41. I came in for a beer but left the CT41 in the shed.

[nate j]

93mm bottle opener is just that little bit nicer to use.

Did not know they were different bottle openers in the Alox.

Yes, they are slightly bigger & beefier on the 93 mm knives than the 91 mm knives, but it is difficult to tell unless you've either held them in your hands or looked at some good comparison pics.

[stealth007s]

I used the main blade on my Cadet to open a package from my Dad and Sister containing three nice boxes of chocolate; chocolate covered cashews, peanut butter meltaways and chocolate and peanut butter pretzels 

[Monrogue]

I used the pruner blade on my Rogue as a sort of toothpick, and it worked well enough.  I just have to be careful   I guess that helps with the lack of scale tools, but no alternative for tweezers on the Rogue.  If it had the pliers, that would help.  That's part of why I want to combine my Mechaneer and Rogue.

[ToolJoe]

  I used the small screwdriver on my Super Tinker to tighten the screws for the cabinet under the sink in our downstairs bathroom.

[NAB]

Vic Ranger to remove the rubber feet off of some speakers.

[Monrogue]

I've been using the pruner blade on my Rogue for various cutting tasks, like opening boxes and cutting the plastice around packing slips on said boxes.

[Caranthanus]

  ... hazelnuts opener


 

 

[mrynnr]

[JAfromMn]

Wired in a fuse box with my electrican

[SAK Guy]