Multitool.org Forum
+-

Hello Lurker! Remove this ad and much more by logging in.


Swapping the corkscrew/phillips on a SAK - A how to.

Neil · 19 · 14604
« previous next »
Pages: 1   Go Down

gb Offline Neil

  • Multitool.org Main Site Manager
  • *
  • Zombie Apprentice
  • ********
    • Posts: 15,287
Swapping the corkscrew/phillips on a SAK - A how to.
on: February 02, 2009, 08:46:24 PM
As requested by max6166 here's a quick run down of how to replace a corkscrew with a phillips driver on a SAK.  In this case a Waiter.  I've shown these pics before in some ancient thread but I can't find it  :think: so here they are again :)

Step 1 - remove the scales of your victim



Step 2 - file off the head of the corkscrew pin, you can also drill it out if you're careful



Step 3 - using a small nail or punch smaller than the pin, knock the pin out. At this stage the backspring will shift out of place. Panic not, slot your previously extracted screwdriver into place as best you can and then use a vice to compress the arrangement until the pin holes all line up.



Step 4 - take a small piece of 2.25mm diameter brass rod that you've tapered a little at one end and gently tap into through the hole. Once its in you can release the knife from the vice



Step 5 - now snip, cut or saw off the brass rod until you have around 1.5mm proud of either side (hint, dremell cut off wheel is good) and begin peening.  Do not over peen, keep checking the action to make sure you don't do it too tight.



Step 6 - rescale and admire your handiwork. Or if you overdid the peening go back to step 2 :)

click for big versions

Step 7 - Share with us how it turned out  :tu:

Neil
I'm not taking any more mod orders at present, sorry.

Offline max6166

  • No Life Club
  • ******
    • Posts: 1,547
Re: Swapping the corkscrew/phillips on a SAK - A how to.
Reply #1 on: February 02, 2009, 09:02:06 PM
What a great tutorial, Neil! I am sure many people will find this very useful. Thank you very much for posting it.  :cheers:
[

england Offline Benner

  • Global Tuffy
  • *
  • Absolute Zombie Club
  • *********
    • Posts: 28,081
  • Just Awesome! And a Slayer of Polar Bear!
Re: Swapping the corkscrew/phillips on a SAK - A how to.
Reply #2 on: February 02, 2009, 09:07:39 PM
Great tutorial buddy.  :tu:
I'm back!!

scotland Offline Gareth

  • Admin Team
  • Point Of No Return
  • *
    • Posts: 36,707
Re: Swapping the corkscrew/phillips on a SAK - A how to.
Reply #3 on: February 02, 2009, 09:22:19 PM
Making it an Apprentice.  http://www.sakwiki.com/tiki-index.php?page=Apprentice+Victorinox

Great tutorial; nice and clear.  Also a great little knife.  :tu:
Be excellent to each other and always know where your towel is.
Merit Badges Participate  in Challenge thread and post a photo of a Delemont SAK for thirty (30) consecutive days. Must start a thread with a photo of your birth year SAK Start a new thread and post a photo of the minimal sak (2 layers or fewer) for thirty (30) consecutive days. Start a new thread with a photo showing the axe in use Start a new thread and post a photo of a traditional folder for thirty (30) consecutive days. Start a new thread including a photo of shooting at least two (2) different airguns and at least one (1) photo of target (airguns) Must have a review written in the proper format and posted on the Main Site Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Participate in a Challenge thread and post a photo of  a Case knife  for 30 days Participate  in a Challenge thread and post a photo of a LM Pocket Survival Tool for thirty (30) consecutive days.  Post a pic for Halloween of your pumpkin (or turnip or gourd or whatever you traditionally carve for Halloween!) being carved by any SAK, multitool, pocket or woods knife you may own!  Only available once a year Start a new thread with a photo of your custom ALOX with scissors Start a new thread showing photos of your outdoor cooking Start a new thread with photos of camping, including those showing preferred camping equipment Start a new thread and post a photo of a flashlight as part of your EDC Start a new thread with a photo of a modded knife or multitool with your EDC Start a new thread with a photo of custom or non standard SAK scales in your collection

gb Offline Mike, Lord of the Spammers!

  • Chief of the Absolutely No Life Club!
  • *
  • Abandon All Hope Ye Who Enter Here...
  • ***********
    • Posts: 42,975
  • Why haven't you got a Farmer yet!
Re: Swapping the corkscrew/phillips on a SAK - A how to.
Reply #4 on: February 02, 2009, 10:09:13 PM
Damn fine tutorial mate :tu:

If you've got time, maybe you could do some for Sosakonline :)
Give in, buy several Farmer's!!!!!!

england Offline DaveK

  • Zombie Apprentice
  • ********
    • Posts: 13,377
  • Sing, Michael, sing. On the route of the 19 Bus!
Re: Swapping the corkscrew/phillips on a SAK - A how to.
Reply #5 on: February 02, 2009, 10:17:23 PM
Nice trick that Neil - nice one!
I used to come here a lot.

us Offline Poncho65

  • Global Moderator
  • *
  • Just Bananas
  • *
    • Posts: 86,013
Re: Swapping the corkscrew/phillips on a SAK - A how to.
Reply #6 on: February 02, 2009, 10:59:17 PM
Cool thanks for that Neil :tu: Very informative and clear :)
Merit Badges Post your pocket dump photos then challenge two more members who must post their pocket dump photos within 24hrs for you to get the badge. Must update or add a page on the Multitool.org Multitool Encyclopedia Carry an orange item and post a picture of it everyday for 30 days. Start a thread with a photo of at least ten OPT's in your collection Participate in a challenge by carrying  a Leatherman Pulse or ST200 and post a photo of it  for thirty (30) consecutive days. Start a new thread and post a photo of the Leatherman MiniTool for thirty (30) consecutive days. In this challenge,  carry one(1) Pliers-based or Non-pliers multitool that we always have prejudice against, hate or even fear and post a picture everyday for 30 days Using EDC items randomly selected with a poker hand, post a photo of your EDC or a component of the EDC that got used during the course of the day for 4 weeks (or 30 consecutive days) In the spirit of the Batman utility belt. A 30 day challenge were you have to have at least 2 things clipped to your belt (preferably more). Start a thread and post a picture of your clipped gear each day for 30 days. Participate  in a Challenge thread and post a photo of a Leatherman Skeletool for thirty (30) consecutive days. Only for the 14th year Anniversary Challenge. Post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. You have one of your pictures in the 2020 calendar or in top three of the calendar poll in any month of the given year. Participate  in a Challenge thread and post a photo of a LM Pocket Survival Tool for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread and post a photo of the LM Crunch  Multitool for fifteen (15) consecutive days. Start a new thread and post a photo of the keychain for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. You have one of your pictures in the 2017 calendar or in top three of the calendar poll in any month of the given year. You have one of your pictures in the 2018 calendar or in top three of the calendar poll in any month of the given year. You have one of your pictures in the 2019 calendar or in top three of the calendar poll in any month of the given year. Start a new thread and post a photo of the multitool for thirty (30) consecutive days.

spam Offline glorn

  • No Life Club
  • ******
    • Posts: 1,223
  • His name is Robert Paulson.
Re: Swapping the corkscrew/phillips on a SAK - A how to.
Reply #7 on: February 03, 2009, 05:15:42 AM
Excellent! Thanks!


Now.. could you show us how to swap the Phillips for a corkscrew?  :think:



 ;)
G

gb Offline Neil

  • Multitool.org Main Site Manager
  • *
  • Zombie Apprentice
  • ********
    • Posts: 15,287
Re: Swapping the corkscrew/phillips on a SAK - A how to.
Reply #8 on: February 03, 2009, 10:52:43 AM
Quote from: glorn on February 03, 2009, 05:15:42 AM
Excellent! Thanks!
Now.. could you show us how to swap the Phillips for a corkscrew?  :think:

 ;)

 ::)  :D

Mike, I will do something for Sosakonline just don't hold me to a time frame :)

Neil
I'm not taking any more mod orders at present, sorry.

england Offline Benner

  • Global Tuffy
  • *
  • Absolute Zombie Club
  • *********
    • Posts: 28,081
  • Just Awesome! And a Slayer of Polar Bear!
Re: Swapping the corkscrew/phillips on a SAK - A how to.
Reply #9 on: February 03, 2009, 12:35:54 PM
Why does that liner have the recessed section around the pin on the left?  Can't say I've seen one of those before.
I'm back!!

scotland Offline Gareth

  • Admin Team
  • Point Of No Return
  • *
    • Posts: 36,707
Re: Swapping the corkscrew/phillips on a SAK - A how to.
Reply #10 on: February 03, 2009, 12:51:42 PM
Quote from: Benner on February 03, 2009, 12:35:54 PM
Why does that liner have the recessed section around the pin on the left?  Can't say I've seen one of those before.

You'll see that on newer knives.  I don't know when exactly but Vic started making their blade tangs slimmer a few years back.  Rather than put a spacer next to the blade they put that indent into the scale.  I'm not sure I've explained that very well.  :think:
Be excellent to each other and always know where your towel is.
Merit Badges Participate  in Challenge thread and post a photo of a Delemont SAK for thirty (30) consecutive days. Must start a thread with a photo of your birth year SAK Start a new thread and post a photo of the minimal sak (2 layers or fewer) for thirty (30) consecutive days. Start a new thread with a photo showing the axe in use Start a new thread and post a photo of a traditional folder for thirty (30) consecutive days. Start a new thread including a photo of shooting at least two (2) different airguns and at least one (1) photo of target (airguns) Must have a review written in the proper format and posted on the Main Site Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Participate in a Challenge thread and post a photo of  a Case knife  for 30 days Participate  in a Challenge thread and post a photo of a LM Pocket Survival Tool for thirty (30) consecutive days.  Post a pic for Halloween of your pumpkin (or turnip or gourd or whatever you traditionally carve for Halloween!) being carved by any SAK, multitool, pocket or woods knife you may own!  Only available once a year Start a new thread with a photo of your custom ALOX with scissors Start a new thread showing photos of your outdoor cooking Start a new thread with photos of camping, including those showing preferred camping equipment Start a new thread and post a photo of a flashlight as part of your EDC Start a new thread with a photo of a modded knife or multitool with your EDC Start a new thread with a photo of custom or non standard SAK scales in your collection

england Offline Benner

  • Global Tuffy
  • *
  • Absolute Zombie Club
  • *********
    • Posts: 28,081
  • Just Awesome! And a Slayer of Polar Bear!
Re: Swapping the corkscrew/phillips on a SAK - A how to.
Reply #11 on: February 03, 2009, 12:53:31 PM
Quote from: Gareth UK on February 03, 2009, 12:51:42 PM
Quote from: Benner on February 03, 2009, 12:35:54 PM
Why does that liner have the recessed section around the pin on the left?  Can't say I've seen one of those before.

You'll see that on newer knives.  I don't know when exactly but Vic started making their blade tangs slimmer a few years back.  Rather than put a spacer next to the blade they put that indent into the scale.  I'm not sure I've explained that very well.  :think:

No I get ya!  :tu:

Thanks for that.
I'm back!!

gb Offline Mike, Lord of the Spammers!

  • Chief of the Absolutely No Life Club!
  • *
  • Abandon All Hope Ye Who Enter Here...
  • ***********
    • Posts: 42,975
  • Why haven't you got a Farmer yet!
Re: Swapping the corkscrew/phillips on a SAK - A how to.
Reply #12 on: February 03, 2009, 01:27:37 PM
Quote from: NKB on February 03, 2009, 10:52:43 AM
Quote from: glorn on February 03, 2009, 05:15:42 AM
Excellent! Thanks!
Now.. could you show us how to swap the Phillips for a corkscrew?  :think:

 ;)

 ::)  :D

Mike, I will do something for Sosakonline just don't hold me to a time frame :)

Neil
Good man :tu:
Give in, buy several Farmer's!!!!!!

us Offline hawkchucker

  • *
  • *
  • No Life Club
  • ******
    • Posts: 4,783
  • I miss Benner
Re: Swapping the corkscrew/phillips on a SAK - A how to.
Reply #13 on: February 03, 2009, 08:45:27 PM
Great job on that, and that I would say is the perfect off day Sak!

Now make me one!
S

us Offline donvito

  • No Life Club
  • ******
    • Posts: 2,562
Re: Swapping the corkscrew/phillips on a SAK - A how to.
Reply #14 on: February 03, 2009, 09:41:20 PM
Great tutorial Neil thank you  :tu: :tu:, keep em coming  :cheers:

scotland Offline Gareth

  • Admin Team
  • Point Of No Return
  • *
    • Posts: 36,707
Re: Swapping the corkscrew/phillips on a SAK - A how to.
Reply #15 on: February 10, 2009, 04:48:53 PM
well I liked the look of this so much I've got a Tinker Small on the way to do one for myself.  :D
Be excellent to each other and always know where your towel is.
Merit Badges Participate  in Challenge thread and post a photo of a Delemont SAK for thirty (30) consecutive days. Must start a thread with a photo of your birth year SAK Start a new thread and post a photo of the minimal sak (2 layers or fewer) for thirty (30) consecutive days. Start a new thread with a photo showing the axe in use Start a new thread and post a photo of a traditional folder for thirty (30) consecutive days. Start a new thread including a photo of shooting at least two (2) different airguns and at least one (1) photo of target (airguns) Must have a review written in the proper format and posted on the Main Site Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Participate in a Challenge thread and post a photo of  a Case knife  for 30 days Participate  in a Challenge thread and post a photo of a LM Pocket Survival Tool for thirty (30) consecutive days.  Post a pic for Halloween of your pumpkin (or turnip or gourd or whatever you traditionally carve for Halloween!) being carved by any SAK, multitool, pocket or woods knife you may own!  Only available once a year Start a new thread with a photo of your custom ALOX with scissors Start a new thread showing photos of your outdoor cooking Start a new thread with photos of camping, including those showing preferred camping equipment Start a new thread and post a photo of a flashlight as part of your EDC Start a new thread with a photo of a modded knife or multitool with your EDC Start a new thread with a photo of custom or non standard SAK scales in your collection

gb Offline Neil

  • Multitool.org Main Site Manager
  • *
  • Zombie Apprentice
  • ********
    • Posts: 15,287
Re: Swapping the corkscrew/phillips on a SAK - A how to.
Reply #16 on: February 10, 2009, 04:55:50 PM
It is one of those tool combinations that I'm surprised is no longer available.

Neil
I'm not taking any more mod orders at present, sorry.

scotland Offline Gareth

  • Admin Team
  • Point Of No Return
  • *
    • Posts: 36,707
Re: Swapping the corkscrew/phillips on a SAK - A how to.
Reply #17 on: February 10, 2009, 05:40:14 PM
Exactly.  I hadn't heard of the Apprentice until I looked at the list on the SAKwiki.  Your tutorial happily coincided with a small Tinker coming up on eBay and so it all seems a bit serendipitous not to do one.  Plus I can put together a Tourist, another 84mm I don't have.  :D
Be excellent to each other and always know where your towel is.
Merit Badges Participate  in Challenge thread and post a photo of a Delemont SAK for thirty (30) consecutive days. Must start a thread with a photo of your birth year SAK Start a new thread and post a photo of the minimal sak (2 layers or fewer) for thirty (30) consecutive days. Start a new thread with a photo showing the axe in use Start a new thread and post a photo of a traditional folder for thirty (30) consecutive days. Start a new thread including a photo of shooting at least two (2) different airguns and at least one (1) photo of target (airguns) Must have a review written in the proper format and posted on the Main Site Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Participate in a Challenge thread and post a photo of  a Case knife  for 30 days Participate  in a Challenge thread and post a photo of a LM Pocket Survival Tool for thirty (30) consecutive days.  Post a pic for Halloween of your pumpkin (or turnip or gourd or whatever you traditionally carve for Halloween!) being carved by any SAK, multitool, pocket or woods knife you may own!  Only available once a year Start a new thread with a photo of your custom ALOX with scissors Start a new thread showing photos of your outdoor cooking Start a new thread with photos of camping, including those showing preferred camping equipment Start a new thread and post a photo of a flashlight as part of your EDC Start a new thread with a photo of a modded knife or multitool with your EDC Start a new thread with a photo of custom or non standard SAK scales in your collection

gb Offline nuphoria

  • Ambidangerous Mistress of Mod
  • Admin Team
  • *
  • Zombie Apprentice
  • *
    • Posts: 15,038
  • I'm not all bad, I'm just drawn that way.
Re: Swapping the corkscrew/phillips on a SAK - A how to.
Reply #18 on: April 30, 2009, 08:40:26 PM
I've been scratching my head a little wondering if this was possible, and lo, Neil has already figured it out, posted a tutorial and put my head scratching to bed  :tu:
A dyslexic man walks in to a bra...

All my music for free: http://soundcloud.com/chrissyvandyke

Pages: 1   Go Up
 

Donations
Operational Funds

Help us keep the Unworkable working!
Donate with PayPal!
April Goal: $300.00
Due Date: Apr 30
Total Receipts: $152.99
PayPal Fees: $8.68
Net Balance: $144.31
Below Goal: $155.69
Site Currency: USD
48% 
April Donations

Community Links
Multitool.org
Multitool Gallery
Multitool Encyclopedia
SAKWiki
Swiss Army Knights

Powered by EzPortal