What Did You Use Your Multitool For Today?

[AHB]

I used 5 straight pins from 5 different SAKs to pin off (?) our new curtains

And you survived to tell your story.. 


 

[Mercury]

I used my pulse to weigh down my belt tonight as I ran for cars(I run the Valet department for a large hotel and we had a wedding with 300 cars!).  Hopefully soon I can transfer back to Security, because I really hate Transportation/Valet/Bell.  Sure I'm the boss, but it still sucks. 

I also used my new Juice SC2(in blue) to cut a few things.  I am really liking this little guy.

[AHB]

Used my Juice to open the box from Heinnies with my new Fenix LD10 R4... 

Excellent flashligt I might add.. 

[Mr. Whippy]

Charge ALX:

1.  Open and fill chain lube on my Stihl 026.  Chain adjustment too.
2.  Removed old twine tied to fencing.
3.  Removed 5mm seat bolt on Ducati 996 to add coolant
4.  Tightened 4mm bolts on Ducati Multistrada bodywork

(4mm and 5mm are on the same bit, which is always in one bit driver.  Combo Phillips/Standard driver in the other)

5. Almost forgot!  Removed burrs on the chainsaw chain.

[sawman]

Charge ALX = one smurfing great tool 

[Mr. Whippy]

Some more fencing work today:

[sawman]

Thanks  those are some GREAT shots!   

[edcgear]

Your gloves looks like new!! 

[Dunc]

Used my Spirit pliers to undo a Maillon in Rope rescue training yesterday .

Dunc

[cerbera147]

I used the saw on my Juice KF4 to carve the first pumpkin of the year 

Did a pretty good job too 

[Threeme2189]

I used the phillips screw driver on my pulse to tighten 2 screws that rattle themselves loose every once in a while.
they hold the lower half of the closing mechanism of my cars trunk door.

[Mercury]

I used the saw on my Juice KF4 to carve the first pumpkin of the year 

Did a pretty good job too 

Nice!   

[Gareth]

I used the saw on my Juice KF4 to carve the first pumpkin of the year 

Did a pretty good job too 

The top pumpkin carving tool is the Vic fish-scaler, I didn't really believe it until I tried it, but it just glides through the pumpkin.

[Mr. Whippy]

I used the saw on my Juice KF4 to carve the first pumpkin of the year 

Did a pretty good job too 

The top pumpkin carving tool is the Vic fish-scaler, I didn't really believe it until I tried it, but it just glides through the pumpkin.

Pr'olly better than a bit driver....

Hmm... 

May have to go back to the "Swiss Champ or CT41" thread...

[cerbera147]

I used the saw on my Juice KF4 to carve the first pumpkin of the year 

Did a pretty good job too 

The top pumpkin carving tool is the Vic fish-scaler, I didn't really believe it until I tried it, but it just glides through the pumpkin.

Great tip Gareth, thanks 

Sadly my minimal SAK range does not extend to the fish-scaler 

[Gareth]

I used the saw on my Juice KF4 to carve the first pumpkin of the year 

Did a pretty good job too 

The top pumpkin carving tool is the Vic fish-scaler, I didn't really believe it until I tried it, but it just glides through the pumpkin.

Great tip Gareth, thanks 

Sadly my minimal SAK range does not extend to the fish-scaler 

   Best drop Neil a message, quick.

 

[Mike 56]

I think someone needs a new SAK. 

[Neil]

I used the saw on my Juice KF4 to carve the first pumpkin of the year 

Did a pretty good job too 

The top pumpkin carving tool is the Vic fish-scaler, I didn't really believe it until I tried it, but it just glides through the pumpkin.

Great tip Gareth, thanks 

Sadly my minimal SAK range does not extend to the fish-scaler 

Dirt cheap

http://www.edcsource.com/Victorinox-Fisherman--new,name,105154,auction_id,auction_details



Here's a picture of my youngest (four at the time) getting creative from last year...

[thebullfrog]

Been using the Skeletool quite a bit since yesterday. Mostly the knife, but the pliers and wire cuter have been used too. It's been an instrumental part of my Nerf gun modding project.

[valvestem125]

I used my Crunch to adjust a rheostat for a heat circulator fan.

[VicX]

I've used both my Victorinox Explorer and my Spirit to perform an autopsy on my recently deceased laptotp.

[Roadie]

Used my Powerlock today making up some cables

[Greenmanbacchus]

I bought a new (for me) car a coupla weeks ago with missing heater knobs.
(My mechanic ordered and received the knobs and now can't find them.  )
So, every morning, LM PST for heat and every afternoon, to switch to A/C
As for today, this morning I had an impromptu removal of an old electric box at work.
Once again, PST to the rescue.

[SlackOne]

My Bear/Crescent Maintenance Pro did it's job of snipping down a bunch of saplings, stray tree limbs, and bamboo out next to the koi pond.  I love the Bear saw...it is *aggressive*, and it complements the big snippers on the Gardener-type tools well.

[Reinier]

I used my CyberTool 34 for what it was designed for: assembling a new computer

Worked very well of course. With a little help from my SwissTool

[cncguy]

Wow, that sounds like fun!  I haven't put together a new system for awhile now. With a cybertool - sounds like even more fun!

[waveman7]

Getting anxious waiting for the mail man to deliver my charge tti, I decided to mow the lawn.  There was a tight spot under our back flow preventer(I think thats what its called) and against a wall.  Since I don't have the mythical and hard to come by Hybrid, I used the straight blade on my Charge Ti to cut the grass down to size.  Could have used a different tool but what the hell.

[scrappy]

I used a swiss champ to remove my battery.

[e17]

Used my SOG to remove my beer's cap

A noble use of it 

[sawman]

I used my Style CS to open packaging and Charge ALX to cuz tags off of some halloween lights we put up today