Multitool.org Forum
+-

Hello Lurker! Remove this ad and much more by logging in.


Combo tool question

kirk13 · 5 · 1324
« previous next »
Pages: 1   Go Down

00 Offline kirk13

  • Admin Team
  • *
  • *
  • Zombie Apprentice
  • *
    • Posts: 15,518
Combo tool question
on: May 22, 2011, 11:42:22 AM
Attention please gurus:hers a silly question.Is there any reason that the combo tool and inline philips cannot be combined on the same layer on a 91mm Vic?Further,is it possible to combine the standard bottle opener/flat driver and philips in the same way?
There is no beginning,or ending,and for this we are thankful,cos now is hard enough to understand!
Merit Badges Must start a thread with a photo of your EDC watch Start a thread with photos of at least five different colored ALOX models in your collection Start a new thread and post a photo of the discontinued sak/mt for thirty (30) consecutive days. Start a new thread with a photo of a modded knife or multitool with your EDC Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Start a new thread with a photo of custom or non standard SAK scales in your collection Start a new thread with photos of a Japanese made PST in your collection

cs Offline edcgear

  • No Life Club
  • ******
    • Posts: 3,570
Re: Combo tool question
Reply #1 on: May 22, 2011, 11:57:16 AM
Not guru, but I think its width of tools in question... As I can remember philips is wider than combo tool/bottle opener

 :think: :think: :think:
ΜΟΛΩΝ ΛΑΒΕ
There is method to my madness....
http://svakodnevnesitnice.blogspot.com/

gb Offline nuphoria

  • Ambidangerous Mistress of Mod
  • Admin Team
  • *
  • Zombie Apprentice
  • *
    • Posts: 15,038
  • I'm not all bad, I'm just drawn that way.
Re: Combo tool question
Reply #2 on: May 22, 2011, 01:44:50 PM
Yep, combo tool will be flapping around opposite a phillips. I have wondered however, if it's possible to use a washer or something to balance these things out.
A dyslexic man walks in to a bra...

All my music for free: http://soundcloud.com/chrissyvandyke

00 Offline kirk13

  • Admin Team
  • *
  • *
  • Zombie Apprentice
  • *
    • Posts: 15,518
Re: Combo tool question
Reply #3 on: May 22, 2011, 09:42:26 PM
Ah!Spacers it is then :D
There is no beginning,or ending,and for this we are thankful,cos now is hard enough to understand!
Merit Badges Must start a thread with a photo of your EDC watch Start a thread with photos of at least five different colored ALOX models in your collection Start a new thread and post a photo of the discontinued sak/mt for thirty (30) consecutive days. Start a new thread with a photo of a modded knife or multitool with your EDC Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Start a new thread with a photo of custom or non standard SAK scales in your collection Start a new thread with photos of a Japanese made PST in your collection

nz Offline HawkeyX

  • Full Member
  • ***
    • Posts: 122
Re: Combo tool question
Reply #4 on: May 23, 2011, 01:00:09 PM
Is the spring shape the same?

Pages: 1   Go Up
 

Donations
Operational Funds

Help us keep the Unworkable working!
Donate with PayPal!
May Goal: $300.00
Due Date: May 31
Total Receipts: $66.45
PayPal Fees: $3.99
Net Balance: $62.46
Below Goal: $237.54
Site Currency: USD
21% 
May Donations

Community Links
Multitool.org
Multitool Gallery
Multitool Encyclopedia
SAKWiki
Swiss Army Knights

Powered by EzPortal