Multitool.org Forum
+-

Hello Lurker! Remove this ad and much more by logging in.


Multi bit holder for the Leatherman Signal

ca Offline benbergman

  • Newbie
  • *
    • Posts: 12
Multi bit holder for the Leatherman Signal
on: December 13, 2020, 10:35:51 PM
Last week I found a Leatherman Signal on clearance, so figured I had to pick it up. I don't really need the survival elements since I don't venture outside the city often, so I figure I should swap out the removable parts for extra bit storage. I'm definitely not the first to do this, but I put my own twist on it.



I noticed that the volume of the whistle was enough to hold two bits. I verified this by popping out the whistle, closing the Signal, and sliding a pair of bits into the cavity. They fit in two different orientations, so I was feeling pretty confident I could make it happen.




I used my flatbed scanner to get reference images for the whistle and file, then made some "blanks" in CAD to ensure my basic measurements would fit. A quick 3D printed test looked promising. Here are the reference scans for those interested.




Next was modelling the bit holders. It took a few iterations. I tried inserting the bits from the end, from the inside, from the outside. All of these left only a very thin wall on the sides of the bits that usually broke when cleaning up the prints. But then it dawned on me to snap the bits in from the sides.




The bits are actually held in more securely than I was expecting. They snap in very easily, yet even smacking the holder into your hand doesn't always pop them out. I made a little hole so I could use the awl to pry them out if needed. Also note that one end of the bit cavity tapers just a tad. Originally I had curved the top of this holder to accommodate a full cavity, but it made the grip while using the knife surprisingly uncomfortable. By shaving down the corners of the cavity I was able to make the holder much lower profile at the expense of not being able to hold bits internally that are very wide at both ends. I think there are only two or three like that, so it was a decent compromise for me.






I also made a bit holder to replace the file. It is inspired by Metro's bit holder, which I think is similar to the one on the MUT.



Now I can carry around 4 flat bits, all within my multitool.



Philips bit lives in the bit driver, then the flat head lives on the outside holder (it is the most sleek there, too wide for that narrowed cavity in the whistle holder, plus Leatherman sells them separately just in case by holder gets loose over time 😅). Since I'm in Canada, a Robertson bit is a must. I'm also a bike commuter, so the 4 and 5mm Allen hex bit rounds out the selection nicely.



The Signal still opens just fine. No collisions.





us Offline SteveC

  • Global Moderator
  • Just Bananas
  • *
    • Posts: 67,363
Re: Multi bit holder for the Leatherman Signal
Reply #1 on: December 14, 2020, 01:17:18 AM
Nice job !    :like:


hr Offline enki_ck

  • Global Moderator
  • *
  • Absolute Zombie Club
  • *
    • Posts: 20,903
  • I may get older but I refuse to grow up.
Re: Multi bit holder for the Leatherman Signal
Reply #2 on: December 14, 2020, 01:33:42 AM
Very well though out and executed. :tu:


it Offline SirVicaLot

  • *
  • Absolutely No Life Club
  • *******
    • Posts: 5,979
Re: Multi bit holder for the Leatherman Signal
Reply #3 on: December 14, 2020, 02:33:24 AM
 :iagree: Great work! And so much more useful for you  :tu:


us Offline Sos24

  • *
  • *
  • Absolutely No Life Club
  • *******
    • Posts: 9,560
Re: Multi bit holder for the Leatherman Signal
Reply #4 on: December 14, 2020, 03:07:01 AM
Great addition.


us Offline Aloha

  • Global Moderator
  • *
  • Point Of No Return
  • *
    • Posts: 31,233
Re: Multi bit holder for the Leatherman Signal
Reply #5 on: December 14, 2020, 03:50:46 AM
 :2tu: Superbly done.   Bravo.   
Esse Quam Videri


au Offline ReamerPunch

  • Thread Killer 2017
  • *
  • Zombie Apprentice
  • ********
    • Posts: 10,185
  • Born to multitask.
Re: Multi bit holder for the Leatherman Signal
Reply #6 on: December 14, 2020, 08:45:25 AM
A much more attractive option than the default ones. I salute your creativity! :salute:
Those look fantastic! I wish I had a set! :like:


au Offline pietervn

  • *
  • No Life Club
  • ******
    • Posts: 1,712
Re: Multi bit holder for the Leatherman Signal
Reply #7 on: December 14, 2020, 10:32:29 AM
That is a fantastic solution for extra bits.

Thanks for taking the time to pic and write it up.

Cheers, Pete


us Offline Poncho65

  • Global Moderator
  • *
  • Just Bananas
  • *
    • Posts: 85,894
Re: Multi bit holder for the Leatherman Signal
Reply #8 on: December 15, 2020, 01:25:51 AM
That is a fantastic solution for extra bits.

Thanks for taking the time to pic and write it up.

Cheers, Pete

 :iagree: :o :salute: :like:


ca Offline AndyS

  • Full Member
  • ***
    • Posts: 240
Re: Multi bit holder for the Leatherman Signal
Reply #9 on: December 15, 2020, 02:16:13 AM
 :sa: :2tu: :dd: :multi:


pt Offline pfrsantos

  • *
  • Absolute Zombie Club
  • *********
    • Posts: 23,201
  • Oxygen and magnesium toghether?! OMg!
Re: Multi bit holder for the Leatherman Signal
Reply #10 on: December 15, 2020, 01:24:45 PM
Pretty kewl! If the pliers didn't open completely, there's still room for some trimming on the bit holder.

 :tu: :tu:
________________________________
It is just a matter of time before they add the word “Syndrome” after my last name.

I don't have OCD, I have OCDEFGHIJKLMNOPQRSTUVWXYZ.

I'd give my right arm to be ambidextrous.

Eff the ineffable, scrut the inscrutable.

IYCRTYSWTMTFOT



ca Offline Metropolicity

  • *
  • No Life Club
  • ******
    • Posts: 3,797
  • Hack Virtuoso
Re: Multi bit holder for the Leatherman Signal
Reply #11 on: December 22, 2020, 02:31:09 AM
I LOVE THIS!


Do you mind if I try to adapt the dual bit holder? I never thought to have them rub against the frame. I never liked that idea, but it sure does make carrying 4 bits possible!
Why stop now?

Visit the whole Skinth family here: http://www.skinthsolutions.com

Keep up with The Skinths on Facebook: http://www.facebook.com/SkinthSolutions

Shapeways - Metro's Q-branch:
http://www.shapeways.com/shops/metro-qbranch

PayPal: metrogradegoods [at} gmail. com


ca Offline benbergman

  • Newbie
  • *
    • Posts: 12
Re: Multi bit holder for the Leatherman Signal
Reply #12 on: December 22, 2020, 05:43:37 AM
Yeah, go nuts. Mine has a thin layer of plastic between the bits, but that probably isn't necessary given how nicely they snap into place. Removing that might slim it down enough to eliminate the rub.


us Offline King_Gorilla

  • Hero Member
  • *****
    • Posts: 510
Re: Multi bit holder for the Leatherman Signal
Reply #13 on: December 25, 2020, 10:32:52 AM
 :like:


Offline NicknameNMS

  • Newbie
  • *
    • Posts: 5
Re: Multi bit holder for the Leatherman Signal
Reply #14 on: December 15, 2021, 04:04:10 AM
ignore this. mb


nz Offline Syncop8r

  • Absolutely No Life Club
  • *******
    • Posts: 8,763
Re: Multi bit holder for the Leatherman Signal
Reply #15 on: December 15, 2021, 05:02:04 AM
Ignoring.  :whistle:


pt Offline pfrsantos

  • *
  • Absolute Zombie Club
  • *********
    • Posts: 23,201
  • Oxygen and magnesium toghether?! OMg!
Re: Multi bit holder for the Leatherman Signal
Reply #16 on: December 15, 2021, 05:19:06 PM
________________________________
It is just a matter of time before they add the word “Syndrome” after my last name.

I don't have OCD, I have OCDEFGHIJKLMNOPQRSTUVWXYZ.

I'd give my right arm to be ambidextrous.

Eff the ineffable, scrut the inscrutable.

IYCRTYSWTMTFOT



 

Donations

Operational Funds

Help us keep the Unworkable working!
Donate with PayPal!
March Goal: $300.00
Due Date: Mar 31
Total Receipts: $379.86
PayPal Fees: $19.62
Net Balance: $360.24
Above Goal: $60.24
Site Currency: USD
120% 
March Donations

Community Links


Powered by EzPortal