Multitool.org Forum
+-

Hello Lurker! Remove this ad and much more by logging in.


Solitaire LED Upgrade

sergemaster · 7 · 5229
« previous next »
Pages: 1   Go Down

us Offline sergemaster

  • *
  • No Life Club
  • ******
    • Posts: 1,058
Solitaire LED Upgrade
on: April 23, 2012, 12:45:28 AM
Amici,
Has anyone else upgraded their Maglite Solitaire to an LED yet? I have and although it is a tad better than the factory bulb, the jury's still out on this one..


Cheers,
Serge 
'I will NOT be threatened by a walking Meatloaf!!' - D. Kessler

us Offline tattoosteve99

  • *
  • Absolutely No Life Club
  • *******
    • Posts: 6,326
Solitaire LED Upgrade
Reply #1 on: April 23, 2012, 01:04:34 AM
I have only one like that. But I use a 10440. That's 3.6 volts. Really all I did was to pull out the old Incan and cut the led wires to the right side. Just make sure you have a led that's rated close to that voltage and there ya go. Oh and you might have to cut the reflector off a bit to fit it. 
If I remember correctly, wait, what was I saying?
Merit Badges Post your pocket dump photos then challenge two more members who must post their pocket dump photos within 24hrs for you to get the badge. Start a thread with photos of at least five different colored ALOX models in your collection Start a new thread with photos of camping, including those showing preferred camping equipment Start a new thread demonstrating paracord knot tying Must start a thread with a photo of your EDC watch Start a thread with photos of at least 1 MTO branded tool in your collection Start a new thread and post a photo of a flashlight as part of your EDC Must start a thread with a photo of your birth year SAK Must buy something on EDCSource

hr Offline enki_ck

  • Global Moderator
  • *
  • Absolute Zombie Club
  • *
    • Posts: 20,935
  • I may get older but I refuse to grow up.
Re: Solitaire LED Upgrade
Reply #2 on: April 23, 2012, 01:13:56 AM
I have one, I made a review of it some time ago on youtube. I like it. It's a solid light, nothing to fancy but enough for nightly trips to the bathroom or to look under furniture for stuff that rolled under there. It's nice to give new life to an old friend.



this is the led module
Merit Badges Must start a thread with a photo of at least five (5) of your watches Must update or add a page on SAKWiki Must put something in order and provide link to the post. Must update or add a page on the Multitool.org Multitool Encyclopedia Must buy something on EDCSource Start a new thread with a photo of custom or non standard SAK scales in your collection Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Start a new thread with a photo of a modded knife or multitool with your EDC Start a thread with photos of at least 5 different Juice models in your collection Start a new thread and post a photo of a flashlight as part of your EDC

us Offline 665ae

  • Formerly known as 665ae
  • No Life Club
  • ******
    • Posts: 3,386
  • blah blah blah
Re: Solitaire LED Upgrade
Reply #3 on: April 23, 2012, 01:17:59 AM
I did few of the a couple years ago using both 5mm and 3mm LED's.  If you use the 3mm LED you don't have to mess with the reflector.
If you took all the intestines out of your body and stretched them end to end... you would die.

Offline Styerman

  • No Life Club
  • ******
    • Posts: 3,572
Re: Solitaire LED Upgrade
Reply #4 on: April 27, 2012, 05:41:12 AM
Where did you get that Mod. ?

I've still got a bunch of sidelined Solitares .

Chris

us Offline tattoosteve99

  • *
  • Absolutely No Life Club
  • *******
    • Posts: 6,326
Solitaire LED Upgrade
Reply #5 on: April 27, 2012, 08:47:04 AM
If I remember correctly, wait, what was I saying?
Merit Badges Post your pocket dump photos then challenge two more members who must post their pocket dump photos within 24hrs for you to get the badge. Start a thread with photos of at least five different colored ALOX models in your collection Start a new thread with photos of camping, including those showing preferred camping equipment Start a new thread demonstrating paracord knot tying Must start a thread with a photo of your EDC watch Start a thread with photos of at least 1 MTO branded tool in your collection Start a new thread and post a photo of a flashlight as part of your EDC Must start a thread with a photo of your birth year SAK Must buy something on EDCSource

hr Offline enki_ck

  • Global Moderator
  • *
  • Absolute Zombie Club
  • *
    • Posts: 20,935
  • I may get older but I refuse to grow up.
Re: Solitaire LED Upgrade
Reply #6 on: April 27, 2012, 11:02:45 AM
Quote from: Styerman on April 27, 2012, 05:41:12 AM
Where did you get that Mod. ?

I've still got a bunch of sidelined Solitares .

Chris

http://www.ebay.com/sch/i.html?_from=R40&_trksid=p5197.m570.l1313&_nkw=MAGLITE+SOLITAIRE+LED+Upgrade+&_sacat=See-All-Categories

For some reason they're more expensive now, I got mine for $7 shipped.
Merit Badges Must start a thread with a photo of at least five (5) of your watches Must update or add a page on SAKWiki Must put something in order and provide link to the post. Must update or add a page on the Multitool.org Multitool Encyclopedia Must buy something on EDCSource Start a new thread with a photo of custom or non standard SAK scales in your collection Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Start a new thread with a photo of a modded knife or multitool with your EDC Start a thread with photos of at least 5 different Juice models in your collection Start a new thread and post a photo of a flashlight as part of your EDC

Pages: 1   Go Up
 

Donations
Operational Funds

Help us keep the Unworkable working!
Donate with PayPal!
April Goal: $300.00
Due Date: Apr 30
Total Receipts: $115.65
PayPal Fees: $7.03
Net Balance: $108.62
Below Goal: $191.38
Site Currency: USD
36% 
April Donations

Community Links
Multitool.org
Multitool Gallery
Multitool Encyclopedia
SAKWiki
Swiss Army Knights

Powered by EzPortal