Multitool.org Forum
+-

Hello Lurker! Remove this ad and much more by logging in.


How to eliminate the the color in alox?

alexTOOL · 8 · 752
« previous next »
Pages: 1   Go Down

es Offline alexTOOL

  • No Life Club
  • ******
    • Posts: 1,240
How to eliminate the the color in alox?
on: January 22, 2017, 07:22:34 PM
Hi guys

How would be possible to eliminate the color in an Alox SAK?  :think:

Example from orange to silver

With a Dremel?

Could be done by hand? I don´t have a Dremel.

Any cons? Less protection? Oxidation?

Thanks!!!  :tu:

gb Offline AimlessWanderer

  • *
  • Zombie Apprentice
  • ********
    • Posts: 17,518
  • I'm not a pessimist, I'm an experienced optimist!
Re: How to eliminate the the color in alox?
Reply #1 on: January 22, 2017, 07:32:32 PM
9" angle grinder  >:D


The easiest way is to swap it with someone who wants an orange one for their silver one   :P


The cantankerous but occasionally useful member, formally known as 50ft-trad

bavaria Offline Tomcat_81

  • *
  • Hero Member
  • *****
    • Posts: 584
Re: How to eliminate the the color in alox?
Reply #2 on: January 22, 2017, 09:26:00 PM
Well- ELectric OXidating aluminium creates a thin yet way more durable layer on the very weak aluminium (Aluminium oxides are among the most durable materials you can use for sanding materials).
If you remove this coating, the handles will wear off just a bit quicker. IMHO it'll be very hard to find a means of eroding the annoying orange (o tempora, o mores) without destroying at least a part of the texture. I've seen a couple of aloxes which had obviously been dremeld with a wire brush - which looked rather messy to me.

Good luck!
Tomcat
Sent from my Boconcept sofa, using the 'post'-button

Owing a beer to Whoey since 2016
Merit Badges Start a thread with a photo of a repair you made with duct tape Start a new thread with photos of your titanium gear with a multitool or sak Start a new thread with a photo showing the axe in use Must start a thread with a photo of at least three (3) of your watches Start a new thread with a photo showing the Hook in use Must start a thread with a photo of your birth year SAK

us Offline cody6268

  • Absolutely No Life Club
  • *******
    • Posts: 6,230
Re: How to eliminate the the color in alox?
Reply #3 on: January 23, 2017, 02:16:19 AM
Why don't you just buy the normal uncolored version?
Merit Badges Participate in a Challenge thread, carry a Buck knife or tool, and post a photo every day for 30 consecutive days. Participate in a Challenge and post a photo of a Utility Knife for thirty (30) consecutive days. Start a new thread with photos of your chainsaws Participate in a Challenge thread and post a photo of a SAK-alike, aka multi-layered, knife-based pocket tools for thirty (30) consecutive days. In this challenge,  carry one(1) Pliers-based or Non-pliers multitool that we always have prejudice against, hate or even fear and post a picture everyday for 30 days Participate in a Challenge thread and post a photo of a 'folding hunter' knife that isn't a Buck 110 for thirty (30) consecutive days. Participate and contribute in Challenge thread and post a photo of either an Axe, MT/Folding knife or Fixed blade (picked at the beginning of challenge) for thirty (30) consecutive days. Participate in a Challenge thread and post a photo of a Spyderco knife for thirty (30) consecutive days. Start a new thread with photos of your titanium gear with a multitool or sak Participate  in Challenge thread and post a photo of a SAK Soldier for thirty (30) consecutive days. Participate in a challenge thread and post a photo of a SAK Cybertool (any variant), Swisschamp, Champion or Toolchest for thirty (30) consecutive days. Participate  in Challenge thread and post a photo of a Fieldmaster SAK for thirty (30) consecutive days. Participate  in Challenge thread and post a photo of a Buck 112 Ranger for thirty (30) consecutive days. Start a new thread and post a photo of the 110 knife for thirty (30) consecutive days. Start a new thread and post a photo of the leatherman (supertool, core, hacks) for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread and post a photo of a flashlight as part of your EDC Start a new thread and post a photo of a traditional folder for thirty (30) consecutive days. Start a new thread and post a photo of the Vic Huntsman for thirty (30) consecutive days. Start a new thread with photos of your zip ties in use

au Offline pietervn

  • *
  • No Life Club
  • ******
    • Posts: 1,770
Re: How to eliminate the the color in alox?
Reply #4 on: January 23, 2017, 05:13:22 AM
I have used Oven Cleaner on LM Squirt scales with success

Pete
Merit Badges Start a new thread with a photo of custom or non standard SAK scales in your collection Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Must start a thread with a photo of your birth year SAK Start a new thread with photos of at least 5 different 111mm models in your collection Must start a thread showing a photo of at least eight BO tools Must start a thread with a photo of your stayglow SAK Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread with photos of your titanium gear with a multitool or sak Must start a thread with a photo of at least five (5) of your watches Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Start a new thread with a photo of a modded knife or multitool with your EDC

se Offline Fortytwo

  • No Life Club
  • ******
    • Posts: 1,285
Re: How to eliminate the the color in alox?
Reply #5 on: January 23, 2017, 02:53:49 PM
I would go for the trade solution. The silver should more common so you might be able to make a deal where the other part pays postage or similar but there's also the problem with raw aluminium that it oxidises unevenly and looks rather messy. 
Merit Badges Start a new thread and post a picture of a fish or fishing kit with a multitool Start a new thread and post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Start a new thread with photos of your chainsaws Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread and post a photo of the minimal sak (2 layers or fewer) for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread with a photo of custom or non standard SAK scales in your collection

es Offline alexTOOL

  • No Life Club
  • ******
    • Posts: 1,240
Re: How to eliminate the the color in alox?
Reply #6 on: January 24, 2017, 12:45:07 AM
Quote from: cody6268 on January 23, 2017, 02:16:19 AM
Why don't you just buy the normal uncolored version?

Thanks  :P

Bacause it is not a standard model in alox. So you will need a custom made. So easy!  :facepalm:

se Offline Fortytwo

  • No Life Club
  • ******
    • Posts: 1,285
Re: How to eliminate the the color in alox?
Reply #7 on: January 24, 2017, 01:57:54 AM
Quote from: alexTOOL on January 24, 2017, 12:45:07 AM
Quote from: cody6268 on January 23, 2017, 02:16:19 AM
Why don't you just buy the normal uncolored version?

Thanks  :P

Bacause it is not a standard model in alox. So you will need a custom made. So easy!  :facepalm:

I see, I would probably still go with drilling out the pins and modifying it. Yes, it's a bit of work and you'd have to have a donor (that could of course get the orange scales) but the raw aluminium will always look dirty. I've sanded off the anodising on a flat comb and even then the new oxidation looks dirty and uneven, I can only assume it would look even worse on a textured scale.
Merit Badges Start a new thread and post a picture of a fish or fishing kit with a multitool Start a new thread and post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Start a new thread with photos of your chainsaws Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread and post a photo of the minimal sak (2 layers or fewer) for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread with a photo of custom or non standard SAK scales in your collection

Pages: 1   Go Up
 

Donations
Operational Funds

Help us keep the Unworkable working!
Donate with PayPal!
May Goal: $300.00
Due Date: May 31
Total Receipts: $55.09
PayPal Fees: $3.15
Net Balance: $51.94
Below Goal: $248.06
Site Currency: USD
17% 
May Donations

Community Links
Multitool.org
Multitool Gallery
Multitool Encyclopedia
SAKWiki
Swiss Army Knights

Powered by EzPortal