Hi Crokan,Nice work and nearly what l am currently planning for a Wave - the parts are on their way from Loki.Basically l was going to do the same but l was going to keep the large flat driver and loose the tiny scissors. These will be replaced by Wingman scissors or maybe SAK scissors instead of the serrated knife.Did you have any issues when you removed the plier rests? My donor wave is a newer one with the thicker rests rather than the earlier flimsy ones that can be easily bent out of the way.Cheers George
Very solid setup crokan
Quote from: Poncho65 on March 18, 2017, 01:18:59 AMVery solid setup crokan thanks was thinking about outside scissors but everything allready there feels more important.. only thing i can skip would be plainedge blade since i always carry a pocket knife but .. always good to have buut i could skip the scissors overall and put in an extra driver i guess
Quote from: crokan on March 18, 2017, 01:28:08 AMQuote from: Poncho65 on March 18, 2017, 01:18:59 AMVery solid setup crokan thanks was thinking about outside scissors but everything allready there feels more important.. only thing i can skip would be plainedge blade since i always carry a pocket knife but .. always good to have buut i could skip the scissors overall and put in an extra driver i guessI would keep the scissors and you could always track down ine if the bit adapters that fit over the LM square Phillips and make it a bit driver that will work with the flat bits and regular hex bits
hi man i have the same one, it was no problem at all just take a tiny screwdriver and bend it out when the plierhead is removed and then hammer the pin that holds the lockspring down to size
Quote from: crokan on March 18, 2017, 12:54:24 AMhi man i have the same one, it was no problem at all just take a tiny screwdriver and bend it out when the plierhead is removed and then hammer the pin that holds the lockspring down to sizeSo just to clarify, you bent the thicker type of Wave plier post with a screwdriver?I thought that it looks too thick to bend out of the way and l was thinking of filing them off or even putting them on the mill.Also as l'm new to this game, l'm not sure which pin l need to hammer down to size?Cheers George
Can try o take a picture or two i removed the bladelock and the plier rest pin completely, did you wanna save the bladelock and just remove the pin?
Hi guys after playing around alot with my waves (can be seen in time to start my wave mods)I have finally setteled on one of my settups! (probably... still not completely sure about the scissors)Here is the Dedicated Wave!(Image removed from quote.)
Quote from: crokan on March 18, 2017, 11:57:21 AMCan try o take a picture or two i removed the bladelock and the plier rest pin completely, did you wanna save the bladelock and just remove the pin?Hi Crokan,Thanks for your explanation, this will only be my third mod a most complicated - the first was a Kick with a saw and scissors and the second was a PST Il with a pocket clip.Yes my plan was to just remove the plier rest pin.Do you think the big phillips and the awl + long small screwdriver will work if l just file/mill away the plier rest pin?I think l now know what you ended up doing. I guess the blade lock needs to come out in order to fit the rebar plier head.At this point in time l was going to leave the Wave pliers.Cheers George
I really love it. I don't at all like the eyeglass screwdriver. I might have tried to trade your scissors for a large flat head. Nice work though man -- not a fan of bit exchangers in the tool itself.
Quote from: NetsNJ on March 19, 2017, 11:24:50 PMI really love it. I don't at all like the eyeglass screwdriver. I might have tried to trade your scissors for a large flat head. Nice work though man -- not a fan of bit exchangers in the tool itself. Agreed. The bit exchangers seem like an awesome idea but l recently came to the conclusion that a 3D phillips, a small/med screwdriver nd a large screwdriver are all that are really needed as far as drivers go. The 3D phillips has a bit kit and this is superior to the normal Wave/Charge driver set up.My plan is to go with the above 3 drivers and have;a) an awl and a can opener and change the serrated blade for the Wingman/SAK scissors or b) keep the original scissors and choose between the awl and the can openerIf only there was room for one extra tool on the Wave...George
Do Zoidbergs combo tool: serrated blade awl and bottleopener ;D