Multitool.org
 
Welcome, Guest. Please login or register.
Did you miss your activation email?

Login with username, password and session length
+-

Hello Lurker! Remove this ad and much more by logging in.


Leatherman Wave Mod - Complete! 2385

Jr. Member Posts: 51
Leatherman Wave Mod - Complete!
« on: August 19, 2017, 06:43:51 PM »
Hi Guys,

Managed to finish my Leatherman Wave yesterday. The last mod was robbing some victorinox scissors to add instead of the serrated blade. The others include a Rebar head and awl.

I think this set up is pretty good, and drilling the Victorinox scissor pivot didn't cause too many issues! (I uses TCT drill bits and a hand drill)

Here are the photos:







Hope you like it.

Cheers
Global Moderator Absolutely No Life Club Posts: 7,490
Re: Leatherman Wave Mod - Complete!
« Reply #1 on: August 19, 2017, 07:09:28 PM »
Nice mod  :like:

What tool is the awl from?
Zombie Apprentice Posts: 17,513 I'm not a pessimist, I'm an experienced optimist!
Re: Leatherman Wave Mod - Complete!
« Reply #2 on: August 19, 2017, 07:44:45 PM »
Nice mod  :like:

What tool is the awl from?

Looks like a reground medium driver.

Nice work   :tu:



The cantankerous but occasionally useful member, formally known as 50ft-trad
Global Moderator Abandon All Hope Ye Who Enter Here... Posts: 45,624
Re: Leatherman Wave Mod - Complete!
« Reply #3 on: August 19, 2017, 07:46:20 PM »
Nice job ! and welcome to the forum !    :cheers:

Looks like a Rebar awl Kev  :tu:
Jr. Member Posts: 51
Re: Leatherman Wave Mod - Complete!
« Reply #4 on: August 19, 2017, 08:18:35 PM »
Yes it is a Rebar awl - ground down though to get the tool to close fully!
Zombie Apprentice Posts: 17,513 I'm not a pessimist, I'm an experienced optimist!
Re: Leatherman Wave Mod - Complete!
« Reply #5 on: August 19, 2017, 08:23:10 PM »
 :tu: :salute:



The cantankerous but occasionally useful member, formally known as 50ft-trad
Sr. Member Posts: 287
Re: Leatherman Wave Mod - Complete!
« Reply #6 on: August 22, 2017, 06:49:29 PM »
 :like: :D
Sr. Member Posts: 438 MAJ/APA
Re: Leatherman Wave Mod - Complete!
« Reply #7 on: August 23, 2017, 01:28:24 PM »
Nice 👍

LM: ALX/SLV/TTI, Blast, Core, Crunch, Flair, C2/CS4/KF4/PRO/S2/SC2/SX/XE6, Kick, Leap, Micra, Mini, MUT, OHT, P4, PS4, PST 1/2, Pulse, Rebar, Sideclip, Signal, Skele CX/RX, ST 200/300/EOD/M, Surge, Tread, Wave

GER: Balance, BearST, Cable Dawg, Center Drive/+, Crucial, Diesel, Dime, Fit, Flick, Grappler, Groundbreaker, MP1/400/600/650/700/800, MPT, Radius, Recoil, Steady

SOG: Paratool, Power Assist/Duo/Grab/Lock/Play/Plier, PPP, PT 525/540, Reactor, Switchplier 1/2

SAK: Autotool, SwissTool/RS/RT/S/XBS
Global Moderator He Who Has The Most Nuts, Wins! Posts: 59,031
Re: Leatherman Wave Mod - Complete!
« Reply #8 on: August 23, 2017, 04:32:19 PM »
Great mod and pics :like: :like:

Welcome to :MTO: :cheers:
New User Posts: 1
Re: Leatherman Wave Mod - Complete!
« Reply #9 on: September 05, 2019, 08:14:37 PM »
Not sure if necro is frowned on like this here, but it seems to make more sense than a new post as I’m asking you a direct question about this mod! I’m looking at putting SAK scissors on my Wave, but there’s not a lot of info about- did you manage to have the lock working properly on this, and is there anything specific I need to watch for?
Absolutely No Life Club Posts: 9,816
Re: Leatherman Wave Mod - Complete!
« Reply #10 on: September 06, 2019, 08:39:38 AM »
A great mod Tom  :tu: ... and good question there Ed   :popcorn:

Formerly known as MTMatt
No Life Club Posts: 4,788
Re: Leatherman Wave Mod - Complete!
« Reply #11 on: September 06, 2019, 10:15:49 AM »
You should be able to reprofile the tang of the Vic Scissors so that the lock should work, I did not do this on a Wave myself, but on a Wingman/Sidekick.
And btw, Thread Necro is not one of the 7 Sins here.
Jr. Member Posts: 51
Re: Leatherman Wave Mod - Complete!
« Reply #12 on: September 09, 2019, 05:47:57 PM »
Hi Ed, I didn't mod the scissors at all apart from the pivot hole so they dont work with the liner lock however are fully functional. The liner lock engages with the scissors at 90 degrees so you need to release it to open the scissors fully.

I have seen a mod on here where someone adds a washer or some sort to work with the lock.

Good luck with the mod. PS I managed to drill the scissor pivot hole with a hand drill in case you think you need a drill press.

I have gone back to the serrated blade on mine though as I always have a vic classic on my keys.

Let us know how you get on

 

Donations

Operational Funds

Help us keep the Unworkable working!
Donate with PayPal!
May Goal: $300.00
Due Date: May 31
Total Receipts: $264.99
PayPal Fees: $14.93
Net Balance: $250.06
Below Goal: $49.94
Site Currency: USD
83% 
May Donations

Community Links


Powered by EzPortal
SMF 2.0.17 | SMF © 2019, Simple Machines
Page created in 0.037 seconds with 32 queries.
© 2018 Defender Web & Tool