I honestly can’t say If I’m excited or not. It does look like a neat job but I do see some minor gaps in the material. I honestly don’t even have a Sak to try these on. He said it took 40 minutes to print and used about 10 oz of the plastic material.(...)Sent from my iPhone using Tapatalk
Haha, love the kitten picture. the reason i say this is because I don't have a SAk that has bad scales, last time I tried to take a scale off I ended up damaging the little T&T, i think is what they are called. I do have a Spartan that I could try it on but that would mean I have to take off the original factory scales to put on the new ones:) I think the material he used is called PLA, I'll ask him again when I have a chance.
Quote from: Zhenchok on September 27, 2017, 06:04:01 PMHaha, love the kitten picture. the reason i say this is because I don't have a SAk that has bad scales, last time I tried to take a scale off I ended up damaging the little T&T, i think is what they are called. I do have a Spartan that I could try it on but that would mean I have to take off the original factory scales to put on the new ones:) I think the material he used is called PLA, I'll ask him again when I have a chance. Victorinox scales are not meant to be popped off and on repeatedly. They are held in place with a compression fit after being pressed on with a factory vice. That said, people do pop them on and off but they don't always fit reliably. One of my Compacts was purchased used but in excellent condition. The tools all looked great--all except for the toothpick, which wouldn't move (a previous owner had epoxied the scales and some must have gotten on the toothpick).So, if your SAK scales are like new, you can always pick up a used SAK in great shape with scales that are in less than great shape (and a candidate for your printed scales). If you are unsure about the process of changing scales, there are YouTube videos that can help. If you don't have vice, then check your garage or pick up one of these (I use one to press on scales and it has worked great):Quick-Grip Clamp by NorCal Jim, on Flickr
Yeah given the way 3d printers work it's never high on the quality or durability of the plastics. It's why fidget spinner sellers specifically make a big deal of saying their spinners are not 3d printed. It's fun for art and screwing around but not much else. I have one I print dildos with sometimes.
Quote from: KandiKlover on September 27, 2017, 11:47:24 PMYeah given the way 3d printers work it's never high on the quality or durability of the plastics. It's why fidget spinner sellers specifically make a big deal of saying their spinners are not 3d printed. It's fun for art and screwing around but not much else. I have one I print dildos with sometimes. I'd say the technology of 3D printing is advancing quite rapidly. The carbon fiber filament 91mm scales I have is on par with the stock cellidor in terms of fit.It's not as smooth and I don't think anyone will want to use this for other non-intended purpose (Image removed from quote.)
Quote from: an0nemus on September 28, 2017, 02:31:25 AMQuote from: KandiKlover on September 27, 2017, 11:47:24 PMYeah given the way 3d printers work it's never high on the quality or durability of the plastics. It's why fidget spinner sellers specifically make a big deal of saying their spinners are not 3d printed. It's fun for art and screwing around but not much else. I have one I print dildos with sometimes. I'd say the technology of 3D printing is advancing quite rapidly. The carbon fiber filament 91mm scales I have is on par with the stock cellidor in terms of fit.It's not as smooth and I don't think anyone will want to use this for other non-intended purpose (Image removed from quote.)Meh everyone says that about things their invested in.
I honestly can’t say If I’m excited or not. It does look like a neat job but I do see some minor gaps in the material. I honestly don’t even have a Sak to try these on. He said it took 40 minutes to print and used about 10 oz of the plastic material.
Quote from: Zhenchok on September 27, 2017, 05:34:45 PMI honestly can’t say If I’m excited or not. It does look like a neat job but I do see some minor gaps in the material. I honestly don’t even have a Sak to try these on. He said it took 40 minutes to print and used about 10 oz of the plastic material.I don't know much about 3D printing, but it's surprising that 2 little SAK scales use 10oz of material. Where does the rest go?
Thatis sobad ass looking! How's the fit? Did you use any glue? How do you like it?
Quote from: an0nemus on September 28, 2017, 04:15:35 PMThatis sobad ass looking! How's the fit? Did you use any glue? How do you like it?Thanks, I like it a lot, no glue required and for the most part it is very flush, it just snapped in and applied the vice to be on the safe side. Thanks for the idea, I happen to hear a coworker talking about his 3d printing capabillities and decided to take him for his word
Quote from: Zhenchok on September 28, 2017, 05:05:56 PMQuote from: an0nemus on September 28, 2017, 04:15:35 PMThatis sobad ass looking! How's the fit? Did you use any glue? How do you like it?Thanks, I like it a lot, no glue required and for the most part it is very flush, it just snapped in and applied the vice to be on the safe side. Thanks for the idea, I happen to hear a coworker talking about his 3d printing capabillities and decided to take him for his word youre welcome! It seems you're coworker has proven himself up to the task! How are the toothpick and tweezer? do they slide in and out smoothly?
Quote from: an0nemus on September 28, 2017, 05:17:17 PMQuote from: Zhenchok on September 28, 2017, 05:05:56 PMQuote from: an0nemus on September 28, 2017, 04:15:35 PMThatis sobad ass looking! How's the fit? Did you use any glue? How do you like it?Thanks, I like it a lot, no glue required and for the most part it is very flush, it just snapped in and applied the vice to be on the safe side. Thanks for the idea, I happen to hear a coworker talking about his 3d printing capabillities and decided to take him for his word youre welcome! It seems your coworker has proven himself up to the task! How are the toothpick and tweezer? do they slide in and out smoothly?They do, but hard to grab them. Sent from my iPhone using Tapatalk
Quote from: Zhenchok on September 28, 2017, 05:05:56 PMQuote from: an0nemus on September 28, 2017, 04:15:35 PMThatis sobad ass looking! How's the fit? Did you use any glue? How do you like it?Thanks, I like it a lot, no glue required and for the most part it is very flush, it just snapped in and applied the vice to be on the safe side. Thanks for the idea, I happen to hear a coworker talking about his 3d printing capabillities and decided to take him for his word youre welcome! It seems your coworker has proven himself up to the task! How are the toothpick and tweezer? do they slide in and out smoothly?
Update, I had a SAK that had a lot of flex in the scales and decided to experiment with it. Below are my results. I would also be happy to take any more pictures of the installed scales if you want. Overall I am actually happy with the outcome. Couple thoughts, they fit well, only one side needed a vise, I do like the the textured feel to them as they give it a nice grip. I would say they are at least 95 percent as good as the factory scales, I would want to put epoxy in the center T&T on one of the sides if I wanted it to be perfectly flush. Honestly, I am happy with the outcome and would say that the 3d printed scales are a nice alternative for scales. Only thing I forgot to mention is that the toothpic and tweezer are a bit harder to get out. I also talked to another coworker who apparently also has a 3d Printer he looked at my knife and said that he can make a better version but it would take longer and would use more material. I guess the ones I have are the quickest way to print, 40 minutes is not quick for me. He said if he set the machine to 2 hours it would make the scales more solid. He showed me a plastic toy he made and it did have a more solid plastic look to it, similar to the plastic we see everywhere. These guys are work buddies so getting them to print more than a pair or two would require a "favor" or paying them, no one really shares my excitement for SAKS. I would consider buying a few from them and trading a few for a SAK if anyone is interested. (Image removed from quote.)(Image removed from quote.)(Image removed from quote.)(Image removed from quote.)(Image removed from quote.)(Image removed from quote.)u(Image removed from quote.)(Image removed from quote.)Sent from my iPhone using Tapatalk
Quote from: Zhenchok on September 28, 2017, 04:04:18 PMUpdate, I had a SAK that had a lot of flex in the scales and decided to experiment with it. Below are my results. I would also be happy to take any more pictures of the installed scales if you want. Overall I am actually happy with the outcome. Couple thoughts, they fit well, only one side needed a vise, I do like the the textured feel to them as they give it a nice grip. I would say they are at least 95 percent as good as the factory scales, I would want to put epoxy in the center T&T on one of the sides if I wanted it to be perfectly flush. Honestly, I am happy with the outcome and would say that the 3d printed scales are a nice alternative for scales. Only thing I forgot to mention is that the toothpic and tweezer are a bit harder to get out. I also talked to another coworker who apparently also has a 3d Printer he looked at my knife and said that he can make a better version but it would take longer and would use more material. I guess the ones I have are the quickest way to print, 40 minutes is not quick for me. He said if he set the machine to 2 hours it would make the scales more solid. He showed me a plastic toy he made and it did have a more solid plastic look to it, similar to the plastic we see everywhere. These guys are work buddies so getting them to print more than a pair or two would require a "favor" or paying them, no one really shares my excitement for SAKS. I would consider buying a few from them and trading a few for a SAK if anyone is interested. (Image removed from quote.)(Image removed from quote.)(Image removed from quote.)(Image removed from quote.)(Image removed from quote.)(Image removed from quote.)u(Image removed from quote.)(Image removed from quote.)Sent from my iPhone using TapatalkLooks great! I am glad you decided to go for it. Popping and installing scales for the first time can be a big deal but quickly becomes routine.Just as a point of reference, Vic scales do need a vice and if they snap right on, it is a sign that they are too loose. Vic scales shouldn't snap right on unless they have been re-used. My early installations were not completely flush at first, a sign that I needed to use my clamp to continue to press on all installation points until the scale was flush. Now, all my scale installations are flush.Jim