Multitool.org Forum
+-

Hello Lurker! Remove this ad and much more by logging in.


Guess

Syncop8r · 284 · 11829

england Offline Kev D

  • Absolutely No Life Club
  • *******
    • Posts: 8,566
Re: Guess
Reply #270 on: March 26, 2018, 09:33:56 PM
I'm thinking a hose reamer for either jointing them or putting onto a bulbed spigot

It must be for something fairly soft being plastic


nz Offline zoidberg

  • Global Moderator
  • Point Of No Return
  • *
    • Posts: 37,748
Re: Guess
Reply #271 on: March 26, 2018, 11:15:52 PM
Battery terminal cleaner ?

Correct.   :tu:


nz Offline Syncop8r

  • Absolutely No Life Club
  • *******
    • Posts: 8,763
Re: Guess
Reply #272 on: August 25, 2018, 12:19:17 AM
Here's an easy one, but you have to say what each part is specifically for.
Perhaps if you know what it is you may want to keep quiet and let others guess...
Show content
That means you Zoidberg  :twak:
20180825_093644.jpg
* 20180825_093644.jpg (Filesize: 246.06 KB)
« Last Edit: August 25, 2018, 12:23:02 AM by Syncop8r »


nz Offline zoidberg

  • Global Moderator
  • Point Of No Return
  • *
    • Posts: 37,748
Re: Guess
Reply #273 on: August 25, 2018, 12:53:11 AM
 :ahhh
Show content
:facepalm:


au Offline gregozedobe

  • Absolutely No Life Club
  • *******
    • Posts: 5,090
  • Apparently it is possible to have too many tools;)
Re: Guess
Reply #274 on: August 25, 2018, 06:45:04 AM
 I know what it is, so I'll just give a cryptic clue:

It is associated with a high speed cutting tool.
babola: "Enjoy your tools and don't be afraid to air your opinion and feelings here, but do it in courteous and respectable way toward others, of course."


00 Offline Dutch_Tooler

  • *
  • No Life Club
  • ******
    • Posts: 4,359
Re: Guess
Reply #275 on: August 25, 2018, 02:47:09 PM
Here's an easy one, but you have to say what each part is specifically for.
Perhaps if you know what it is you may want to keep quiet and let others guess...
Show content
That means you Zoidberg  :twak:
Combination wrench for spark plug / wheel nut and screwdriver handle also usable for removing hub caps?
Cheers!
Dutch_Tooler

Location: Southern Germany, most of the time


au Offline gregozedobe

  • Absolutely No Life Club
  • *******
    • Posts: 5,090
  • Apparently it is possible to have too many tools;)
Re: Guess
Reply #276 on: August 25, 2018, 06:00:41 PM
Here's an easy one, but you have to say what each part is specifically for.
Perhaps if you know what it is you may want to keep quiet and let others guess...
Show content
That means you Zoidberg  :twak:
Combination wrench for spark plug / wheel nut and screwdriver handle also usable for removing hub caps?

Well, that is 1 of the 4 functions (spark plug), but what are the other 3 ?  And what object is it used on ?
babola: "Enjoy your tools and don't be afraid to air your opinion and feelings here, but do it in courteous and respectable way toward others, of course."


us Offline cody6268

  • Absolutely No Life Club
  • *******
    • Posts: 5,813
Re: Guess
Reply #277 on: August 25, 2018, 07:15:17 PM
Chainsaw multi-tool, screwdriver for adjustments (and the fuel and lubricant tanks on older models, like Granddad's Stihl 011AV from the 1980s),Wrench is for use on the bolts holding the bar and chain on, as well as the cover.  Also found in the rare and extremely collectible Torx tip (I think that one might be for gas trimmers)  :D


nz Offline Syncop8r

  • Absolutely No Life Club
  • *******
    • Posts: 8,763
Re: Guess
Reply #278 on: August 25, 2018, 10:25:56 PM
Your turn then.
Mine is 16/11mm for McCulloch. Most are 19/13mm for Stihl and Husqvarna.

Perhaps if you know what it is you may want to keep quiet and let others guess...
  ::)
« Last Edit: August 25, 2018, 10:27:38 PM by Syncop8r »


nz Offline Syncop8r

  • Absolutely No Life Club
  • *******
    • Posts: 8,763
Re: Guess
Reply #279 on: September 30, 2018, 11:58:46 PM
Design fault: the chain tension screw is too close to the bar to use the screwdriver (the wrench parts get in the way).  :facepalm:


au Offline TazzieRob

  • *
  • No Life Club
  • ******
    • Posts: 1,449
Re: Guess
Reply #280 on: October 01, 2018, 06:46:57 AM
Design fault: the chain tension screw is too close to the bar to use the screwdriver (the wrench parts get in the way).  :facepalm:

But doesn't your bar need to be lose to be able to adjust the chain tension?


nz Offline Syncop8r

  • Absolutely No Life Club
  • *******
    • Posts: 8,763
Re: Guess
Reply #281 on: October 01, 2018, 12:48:22 PM
Yeah I loosen off the bar nuts a bit... but the bar is still in the same place.  :dunno:


au Offline gregozedobe

  • Absolutely No Life Club
  • *******
    • Posts: 5,090
  • Apparently it is possible to have too many tools;)
Re: Guess
Reply #282 on: October 01, 2018, 01:35:01 PM
Yeah I loosen off the bar nuts a bit... but the bar is still in the same place.  :dunno:

I noticed that bit of poor ergonomics in my (IIRC) Husqvarna 394XP. 
There wasn't enough room to rotate the multi-wrench without bumping against the bar.  Not impossible to adjust, just a bit awkward.
babola: "Enjoy your tools and don't be afraid to air your opinion and feelings here, but do it in courteous and respectable way toward others, of course."


nz Offline Syncop8r

  • Absolutely No Life Club
  • *******
    • Posts: 8,763
Re: Guess
Reply #283 on: October 01, 2018, 01:39:02 PM
Some screnches have the screwdriver offset which would help.


 

Donations

Operational Funds

Help us keep the Unworkable working!
Donate with PayPal!
March Goal: $300.00
Due Date: Mar 31
Total Receipts: $379.86
PayPal Fees: $19.62
Net Balance: $360.24
Above Goal: $60.24
Site Currency: USD
120% 
March Donations

Community Links


Powered by EzPortal