Multitool.org Forum
+-

Hello Lurker! Remove this ad and much more by logging in.


Key ring torx tool for Wave pivots

Max Stone · 4 · 1183
« previous next »
Pages: 1   Go Down

za Offline Max Stone

  • *
  • Absolutely No Life Club
  • *******
    • Posts: 5,982
Key ring torx tool for Wave pivots
on: February 05, 2019, 07:21:06 PM
So I find I need to fine-tune the pivots on my Wave occasionally, but carrying 2 dedicated torx screwdrivers is not very practical.  ???

So I pushed 2 of the T10 security torx bits into a couple of aluminum cable terminators and I now have some portable drivers I can clip on my keyring and use anytime to tweak my Wave (or even do a field strip).  :tu:

I also use these cable terminators for MTs with knurled pivots as they’re easy to resize to push over the rivet, and soft enough not to scratch the handle.

So a tool ‘hack’ for Multitools.  :salute:
2BB3A835-5B0C-4346-B343-8DDE8F86669F.jpeg
* 2BB3A835-5B0C-4346-B343-8DDE8F86669F.jpeg (Filesize: 260.53 KB)
3F88295D-76CB-44B7-974B-AB64604C9E49.jpeg
* 3F88295D-76CB-44B7-974B-AB64604C9E49.jpeg (Filesize: 266.31 KB)
Education is a journey that starts when you realize that knowing a little about something opens the door to the universe.
Merit Badges Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Must start a thread with a photo of at least three (3) of your watches Participate in a challenge thread and post a photo of a SAK Cybertool (any variant), Swisschamp, Champion or Toolchest for sixty (60) consecutive days. Must start a thread with a photo of your EDC watch Start a new thread and post a photo daily of any SAK 74mm or smaller ( you can switch it up daily ) for thirty (30) consecutive days. Start a thread with photos of at least eight different colored ALOX models in your collection Participate in a challenge thread and post a photo of a SAK Cybertool (any variant), Swisschamp, Champion or Toolchest for thirty (30) consecutive days. Participate  in a Challenge thread and post a photo of a LM Pocket Survival Tool for thirty (30) consecutive days. Start a new thread and post a photo of the discontinued sak/mt for thirty (30) consecutive days. Must update or add a page on SAKWiki Start a new thread and post a photo of the modified sak (scale swap not included) for thirty (30) consecutive days. Start a new thread and post a photo of a different SAK each day for thirty (30) consecutive days. Start a new thread with a photo of custom or non standard SAK scales in your collection Start a new thread demonstrating paracord knot tying Start a new thread showing photos of your outdoor cooking Start a thread with photos of at least five different colored ALOX models in your collection Start a new thread and post a photo of a fixed blade for thirty (30) consecutive days.

za Offline Max Stone

  • *
  • Absolutely No Life Club
  • *******
    • Posts: 5,982
Re: Key ring torx tool for Wave pivots
Reply #1 on: February 05, 2019, 07:29:49 PM
(Oops, wrong forum...but will also work for SOGs) :oops:
Education is a journey that starts when you realize that knowing a little about something opens the door to the universe.
Merit Badges Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Must start a thread with a photo of at least three (3) of your watches Participate in a challenge thread and post a photo of a SAK Cybertool (any variant), Swisschamp, Champion or Toolchest for sixty (60) consecutive days. Must start a thread with a photo of your EDC watch Start a new thread and post a photo daily of any SAK 74mm or smaller ( you can switch it up daily ) for thirty (30) consecutive days. Start a thread with photos of at least eight different colored ALOX models in your collection Participate in a challenge thread and post a photo of a SAK Cybertool (any variant), Swisschamp, Champion or Toolchest for thirty (30) consecutive days. Participate  in a Challenge thread and post a photo of a LM Pocket Survival Tool for thirty (30) consecutive days. Start a new thread and post a photo of the discontinued sak/mt for thirty (30) consecutive days. Must update or add a page on SAKWiki Start a new thread and post a photo of the modified sak (scale swap not included) for thirty (30) consecutive days. Start a new thread and post a photo of a different SAK each day for thirty (30) consecutive days. Start a new thread with a photo of custom or non standard SAK scales in your collection Start a new thread demonstrating paracord knot tying Start a new thread showing photos of your outdoor cooking Start a thread with photos of at least five different colored ALOX models in your collection Start a new thread and post a photo of a fixed blade for thirty (30) consecutive days.

es Offline ThePeacent

  • *
  • Zombie Apprentice
  • ********
    • Posts: 14,599
  • Firm believer of Sturgeon's Law
Re: Key ring torx tool for Wave pivots
Reply #2 on: February 06, 2019, 01:42:23 PM
Quote from: Max Stone on February 05, 2019, 07:21:06 PM

So I pushed 2 of the T10 security torx bits into a couple of aluminum cable terminators

I also use these cable terminators for MTs

instead of two T10s, I was expecting to see two T1000s! :D
My toys:

MTs: Surge (2x), Skeletool CX, Rebar, Blast, Fuse, Micra, Squirt (3x), Wave, Crunch, Mini, Spirit (2x), Pro Scout, MP700 (2x), Diesel, Powerlock, PowerPlier (2x), PocketPowerPlier, Blacktip , ST6 (2x), 5WR, A100

SAKs: Bantam, Executive, Ambassador, Minichamp, Classic Alox, Champion, Farmer, Explorer, Swisschamp, Golf Tool, Wenger Champ, EVO 52, Pocket Tool Chest
Merit Badges  Post a pic for Halloween of your pumpkin (or turnip or gourd or whatever you traditionally carve for Halloween!) being carved by any SAK, multitool, pocket or woods knife you may own!  Only available once a year Complete a 30 day challenge for carrying a different Multi tool each day of the week based on one of the daily carry threads Start a new thread with photos of your Buck knives in use Start a new thread and post a photo of the 110 knife for thirty (30) consecutive days.  Start a new thread and post a photo of the Vic Pioneer X for thirty (30) consecutive days. Start a new thread with a photo showing the Hook in use Start a new thread with photos of your chainsaws Start a new thread and post a photo of a flashlight as part of your EDC Start a thread with photos of at least 1 MTO branded tool in your collection Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread and post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Post your pocket dump photos then challenge two more members who must post their pocket dump photos within 24hrs for you to get the badge.

za Offline Max Stone

  • *
  • Absolutely No Life Club
  • *******
    • Posts: 5,982
Re: Key ring torx tool for Wave pivots
Reply #3 on: February 06, 2019, 03:06:10 PM
Now that would be a mod challenge! No torx bits on the T1000... ;)
1F1986DF-FFB5-4A7E-9731-18A5D3E4BDC0.jpeg
* 1F1986DF-FFB5-4A7E-9731-18A5D3E4BDC0.jpeg (Filesize: 223.93 KB)
Education is a journey that starts when you realize that knowing a little about something opens the door to the universe.
Merit Badges Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Must start a thread with a photo of at least three (3) of your watches Participate in a challenge thread and post a photo of a SAK Cybertool (any variant), Swisschamp, Champion or Toolchest for sixty (60) consecutive days. Must start a thread with a photo of your EDC watch Start a new thread and post a photo daily of any SAK 74mm or smaller ( you can switch it up daily ) for thirty (30) consecutive days. Start a thread with photos of at least eight different colored ALOX models in your collection Participate in a challenge thread and post a photo of a SAK Cybertool (any variant), Swisschamp, Champion or Toolchest for thirty (30) consecutive days. Participate  in a Challenge thread and post a photo of a LM Pocket Survival Tool for thirty (30) consecutive days. Start a new thread and post a photo of the discontinued sak/mt for thirty (30) consecutive days. Must update or add a page on SAKWiki Start a new thread and post a photo of the modified sak (scale swap not included) for thirty (30) consecutive days. Start a new thread and post a photo of a different SAK each day for thirty (30) consecutive days. Start a new thread with a photo of custom or non standard SAK scales in your collection Start a new thread demonstrating paracord knot tying Start a new thread showing photos of your outdoor cooking Start a thread with photos of at least five different colored ALOX models in your collection Start a new thread and post a photo of a fixed blade for thirty (30) consecutive days.

Pages: 1   Go Up
 

Donations
Operational Funds

Help us keep the Unworkable working!
Donate with PayPal!
April Goal: $300.00
Due Date: Apr 30
Total Receipts: $152.99
PayPal Fees: $8.68
Net Balance: $144.31
Below Goal: $155.69
Site Currency: USD
48% 
April Donations

Community Links
Multitool.org
Multitool Gallery
Multitool Encyclopedia
SAKWiki
Swiss Army Knights

Powered by EzPortal