Multitool.org Forum
+-

Hello Lurker! Remove this ad and much more by logging in.


Climber Lite with removable LED module

Max Stone · 39 · 2481
« previous next »
Pages: 1 2   Go Down

za Offline Max Stone

  • *
  • Absolutely No Life Club
  • *******
    • Posts: 5,982
Climber Lite with removable LED module
on: April 15, 2020, 10:02:28 PM
I’ve been thinking about this mod for about 6 months, so eventually gave it a go.  :think:

The idea is that the LED is a great little close-proximity light, but has 2 major issues:

1. You can’t get water near it, and
2. You can’t use the LED independently of the SAK

So what if you could clip it off?  :dunno:

The LED module is used without opening it out of the SAK, and it only rotates 90deg to expose the battery compartment. So I figured a simple cut-out slot will allow the module to be lifted out when rotated up, but will still keep the module retained when it’s down.

The problem is that the liners and tools could all slip along the exposed pivot if you simply remove the module, so a tube spacer is needed to keep everything still tight when the LED is out.

I found a nickel-plated brass ferrule the perfect size, 2.5mm hole, 4mm outer diameter. Just needed trimming down to the correct length of 2.9mm to act as a spacer.

Here you can see an original ferrule and the spacer completed. I drilled out the module to 4mm and did a test fit. Then cut the slot, making this slightly less than 4mm so there’s a positive click when it clips onto the spacer.  :tu:
Education is a journey that starts when you realize that knowing a little about something opens the door to the universe.
Merit Badges Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Must start a thread with a photo of at least three (3) of your watches Participate in a challenge thread and post a photo of a SAK Cybertool (any variant), Swisschamp, Champion or Toolchest for sixty (60) consecutive days. Must start a thread with a photo of your EDC watch Start a new thread and post a photo daily of any SAK 74mm or smaller ( you can switch it up daily ) for thirty (30) consecutive days. Start a thread with photos of at least eight different colored ALOX models in your collection Participate in a challenge thread and post a photo of a SAK Cybertool (any variant), Swisschamp, Champion or Toolchest for thirty (30) consecutive days. Participate  in a Challenge thread and post a photo of a LM Pocket Survival Tool for thirty (30) consecutive days. Start a new thread and post a photo of the discontinued sak/mt for thirty (30) consecutive days. Must update or add a page on SAKWiki Start a new thread and post a photo of the modified sak (scale swap not included) for thirty (30) consecutive days. Start a new thread and post a photo of a different SAK each day for thirty (30) consecutive days. Start a new thread with a photo of custom or non standard SAK scales in your collection Start a new thread demonstrating paracord knot tying Start a new thread showing photos of your outdoor cooking Start a thread with photos of at least five different colored ALOX models in your collection Start a new thread and post a photo of a fixed blade for thirty (30) consecutive days.

za Offline Max Stone

  • *
  • Absolutely No Life Club
  • *******
    • Posts: 5,982
Re: Climber Lite with removable LED module
Reply #1 on: April 15, 2020, 10:15:08 PM
Next was to reassemble everything...

I used a Spartan Lite as the donor SAK, and added a scissors layer that I had left over from another build.

Victorinox don’t do this config. The closest is the 5 layer Huntsman Lite, but this is getting a little big for EDC.

With the inline Phillips, this is effectively an Explorer with the LED instead of the magnifier. And now that the LED is removable, why not have a magnifier that can slot in?  :cheers:

So I followed a similar slot direction as used on the Rescue Tool’s removable blade, and it works, but...as the Lite models swap around the Phillips to the opposite end, the magnifier does not close fully. But you can use it in the open position.

What else could you clip into this new mounting point?  :dunno:

Very happy with the result. You do lose backspring tension on the Phillips when the module is out, but I did not want to use a larger diameter spacer otherwise the slotted area would be too weak. It’s a small compromise for a far better tool imo.  :salute:
Education is a journey that starts when you realize that knowing a little about something opens the door to the universe.
Merit Badges Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Must start a thread with a photo of at least three (3) of your watches Participate in a challenge thread and post a photo of a SAK Cybertool (any variant), Swisschamp, Champion or Toolchest for sixty (60) consecutive days. Must start a thread with a photo of your EDC watch Start a new thread and post a photo daily of any SAK 74mm or smaller ( you can switch it up daily ) for thirty (30) consecutive days. Start a thread with photos of at least eight different colored ALOX models in your collection Participate in a challenge thread and post a photo of a SAK Cybertool (any variant), Swisschamp, Champion or Toolchest for thirty (30) consecutive days. Participate  in a Challenge thread and post a photo of a LM Pocket Survival Tool for thirty (30) consecutive days. Start a new thread and post a photo of the discontinued sak/mt for thirty (30) consecutive days. Must update or add a page on SAKWiki Start a new thread and post a photo of the modified sak (scale swap not included) for thirty (30) consecutive days. Start a new thread and post a photo of a different SAK each day for thirty (30) consecutive days. Start a new thread with a photo of custom or non standard SAK scales in your collection Start a new thread demonstrating paracord knot tying Start a new thread showing photos of your outdoor cooking Start a thread with photos of at least five different colored ALOX models in your collection Start a new thread and post a photo of a fixed blade for thirty (30) consecutive days.

se Offline RF52

  • *
  • Absolutely No Life Club
  • *******
    • Posts: 5,780
Re: Climber Lite with removable LED module
Reply #2 on: April 15, 2020, 10:25:35 PM
Very nice! Great idea and good job :hatsoff:

Sent fra min FRD-L09 via Tapatalk

Merit Badges Participate in a Challenge thread and post a photo of  a Case knife  for 30 days Start a new thread and post a photo of the multitool for fifteen (15) consecutive days. Participate  in Challenge thread and post a photo of a Explorer SAK for thirty (30) consecutive days. Participate in a Challenge thread and post a photo of a 'folding hunter' knife that isn't a Buck 110 for thirty (30) consecutive days. Participants shall carry and use one Soldier knife, the model of their choosing, for the duration of the 90 days and post a picture each day. Build your own version of an MRE using off-the-shelf components, post a photo of the completed MRE and store at room temperature for 6 days or more. Consume the MRE after the storage period and post pictures and descriptions of the contents. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Using EDC items randomly selected with a poker hand, post a photo of your EDC or a component of the EDC that got used during the course of the day for 4 weeks (or 30 consecutive days) Participate  in a Challenge thread and post a photo of a Leatherman Skeletool for thirty (30) consecutive days. Must start a thread with a photo of your camo SAK Participate and contribute in Challenge thread and post a photo of either an Axe, MT/Folding knife or Fixed blade (picked at the beginning of challenge) for thirty (30) consecutive days. Participate in a Challenge thread and post a photo of a Spyderco knife for thirty (30) consecutive days. Only for the 14th year Anniversary Challenge. Post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Start a new thread and post a photo of the multitool for seven (7) consecutive days. Participate  in a Challenge thread and post a photo of a LM Pocket Survival Tool for thirty (30) consecutive days. Start a new thread and post a photo of an Axe for thirty (30) consecutive days. Start a new thread and post a photo of a traditional folder for thirty (30) consecutive days. Start a new thread with photos of your slasher/chopper/machete knives in use Start a new thread and post a photo of the keychain for thirty (30) consecutive days. Start a new thread with a photo showing the Swiss Army Knife   Toothpick being used in an unusual way. Start a new thread and post a photo of a fixed blade for thirty (30) consecutive days.

za Offline Max Stone

  • *
  • Absolutely No Life Club
  • *******
    • Posts: 5,982
Re: Climber Lite with removable LED module
Reply #3 on: April 15, 2020, 10:38:26 PM
Thanks RF52.  :hatsoff:
Education is a journey that starts when you realize that knowing a little about something opens the door to the universe.
Merit Badges Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Must start a thread with a photo of at least three (3) of your watches Participate in a challenge thread and post a photo of a SAK Cybertool (any variant), Swisschamp, Champion or Toolchest for sixty (60) consecutive days. Must start a thread with a photo of your EDC watch Start a new thread and post a photo daily of any SAK 74mm or smaller ( you can switch it up daily ) for thirty (30) consecutive days. Start a thread with photos of at least eight different colored ALOX models in your collection Participate in a challenge thread and post a photo of a SAK Cybertool (any variant), Swisschamp, Champion or Toolchest for thirty (30) consecutive days. Participate  in a Challenge thread and post a photo of a LM Pocket Survival Tool for thirty (30) consecutive days. Start a new thread and post a photo of the discontinued sak/mt for thirty (30) consecutive days. Must update or add a page on SAKWiki Start a new thread and post a photo of the modified sak (scale swap not included) for thirty (30) consecutive days. Start a new thread and post a photo of a different SAK each day for thirty (30) consecutive days. Start a new thread with a photo of custom or non standard SAK scales in your collection Start a new thread demonstrating paracord knot tying Start a new thread showing photos of your outdoor cooking Start a thread with photos of at least five different colored ALOX models in your collection Start a new thread and post a photo of a fixed blade for thirty (30) consecutive days.

gb Offline Wspeed

  • *
  • Just Bananas
  • *************
    • Posts: 76,225
Re: Climber Lite with removable LED module
Reply #4 on: April 15, 2020, 10:39:51 PM
Excellent idea and great work  :like: :tu:
fail to prepare prepare to fail
Merit Badges Must put something in order and provide link to the post. Join the brave and happy few, who choose a different path. Enter on the boulevard of broken dreams. Start a new thread with a photo of a modded knife or multitool with your EDC Must post a step by step pictorial of a knife or multitool modification (scale swap not included) For those who posted like a boss. Only for the 14th year Anniversary Challenge. Post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. You have one of your pictures in the 2020 calendar or in top three of the calendar poll in any month of the given year. Start a new thread and post a photo of the LM Crunch  Multitool for thirty (30) consecutive days. Start a new thread and post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Start a new thread and post a photo of a traditional folder for thirty (30) consecutive days. Start a new thread and post a photo of the leatherman (supertool, core, hacks) for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread with a photo showing the Swiss Army Knife   Toothpick being used in an unusual way. You have one of your pictures in the 2019 calendar or in top three of the calendar poll in any month of the given year. Participate in a challenge thread and post a photo of a SAK Cybertool (any variant), Swisschamp, Champion or Toolchest for thirty (30) consecutive days. Start a new thread demonstrating paracord knot tying Start a new thread with photos of your Buck knives in use Must start a thread with a photo of your camo SAK  Post a pic for Halloween of your pumpkin (or turnip or gourd or whatever you traditionally carve for Halloween!) being carved by any SAK, multitool, pocket or woods knife you may own!  Only available once a year Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread including a photo of shooting at least two (2) different airguns and at least one (1) photo of target (airguns)

us Offline Sos24

  • Global Moderator
  • *
  • Zombie Apprentice
  • *
    • Posts: 11,180
Re: Climber Lite with removable LED module
Reply #5 on: April 15, 2020, 10:48:59 PM
Cool mod.
Merit Badges Using EDC items randomly selected with a poker hand, post a photo of your EDC or a component of the EDC that got used during the course of the day for 4 weeks (or 30 consecutive days) Participate  in Challenge thread and post a photo of your EDC or a component of the EDC that got used during the course of the day for thirty (30) consecutive days. Participate  in a Challenge thread and post a photo of a Leatherman Skeletool for thirty (30) consecutive days. Only for the 14th year Anniversary Challenge. Post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Participate and contribute in Challenge thread and post a photo of a different blade each day for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread and post a photo of the discontinued sak/mt for thirty (30) consecutive days. Start a new thread and post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Start a new thread and post a photo of a traditional folder for thirty (30) consecutive days. Participate in a Challenge thread, carry at least one black edc item, and post a photo every day for 30 consecutive days. Participate in a Challenge thread, carry a SAK, duct tape, and paperclip, and post a photo every day for 30 consecutive days. Participate in a Challenge thread, carry a modular tool, and post a photo every day for 30 consecutive days. Participate in a Challenge thread, carry a Buck knife or tool, and post a photo every day for 30 consecutive days. Participate in a Challenge, carry a fire-starting item and post a picture daily  (in use if possible) for 30 days. Lighters, matches, ferro rods, fire pistons, Signal, candles, sparkers, tinder, stoves, bowdrill sets. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Participate in a Challenge thread and post a photo of  a Leatherman Micra  for 30 days Participate in the Challenge thread and post a photo of a Flashlight for thirty (30) consecutive days. Participate in a Challenge thread and post a photo of  a Case knife  for 30 days Participate in a Challenge thread and post a photo  of 84 and 85 mm Swiss Army Knives (and Wengers) for 30 days Start a new thread and post a photo of an Executive or Director for thirty (30) consecutive days. Take part in the christmas pool or a rak type giveaway. Those wanting to say thank you for a rak may also nominate for the santa.

wales Offline magentus

  • Admin Team
  • *
  • Absolute Zombie Club
  • *
    • Posts: 20,940
  • mmmmm SAKrelicious
Re: Climber Lite with removable LED module
Reply #6 on: April 15, 2020, 10:57:32 PM
'Use the force Harry' - Gandalf
Merit Badges Take part in the christmas pool or a rak type giveaway. Those wanting to say thank you for a rak may also nominate for the santa. Join the brave and happy few, who choose a different path. Enter on the boulevard of broken dreams. Test,please ignore Start a new thread and post a photo of the minimal sak (2 layers or fewer) for thirty (30) consecutive days. Start a new thread with photos of your hobo knives in use Start a thread with a photo of a repair you made with duct tape Start a new thread with a photo showing the Hook in use Must post a step by step pictorial of a knife or multitool modification (scale swap not included)

it Offline SirVicaLot

  • *
  • Absolutely No Life Club
  • *******
    • Posts: 5,979
Re: Climber Lite with removable LED module
Reply #7 on: April 15, 2020, 11:01:36 PM
I would call it an enlightened mod  :D :like:
Merit Badges Start a new thread with photos of at least 5 different 111mm models in your collection Participate  in Challenge thread and post a photo of a Farmer X SAK for thirty (30) consecutive days. Start a thread with a photo of a repair you made with duct tape Start a new thread and post a photo of the multitool for thirty (30) consecutive days.  Start a new thread and post a photo of the Vic Pioneer X for thirty (30) consecutive days. Participate in a challenge thread and post a photo of a SAK Cybertool (any variant), Swisschamp, Champion or Toolchest for thirty (30) consecutive days. Must start a thread with a photo of at least five (5) of your watches Start a thread with photos of at least five different colored ALOX models in your collection Join the brave and happy few, who choose a different path. Enter on the boulevard of broken dreams. Participate  in Challenge thread and post a photo of a Fieldmaster SAK for thirty (30) consecutive days. You have one of your pictures in the 2020 calendar or in top three of the calendar poll in any month of the given year. Must put something in order and provide link to the post. Start a new thread with pictures of a Fish Scaler in use Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread with photos of your Mora knives in use Start a new thread with a photo showing the Hook in use Start a new thread with a photo of a modded knife or multitool with your EDC Start a new thread with a photo showing the Swiss Army Knife   Toothpick being used in an unusual way. Must start new thread with photos of multitools (Magazine/Catalogue type photos) Start a new thread and post a photo of the discontinued sak/mt for thirty (30) consecutive days. Start a new thread with a photo of custom or non standard SAK scales in your collection

za Offline Max Stone

  • *
  • Absolutely No Life Club
  • *******
    • Posts: 5,982
Re: Climber Lite with removable LED module
Reply #8 on: April 15, 2020, 11:12:50 PM
Thanks Wim, 🆘, magentus, Sir Vic.  :hatsoff:

...just a light mod to brighten-up the day.  :pok:
Education is a journey that starts when you realize that knowing a little about something opens the door to the universe.
Merit Badges Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Must start a thread with a photo of at least three (3) of your watches Participate in a challenge thread and post a photo of a SAK Cybertool (any variant), Swisschamp, Champion or Toolchest for sixty (60) consecutive days. Must start a thread with a photo of your EDC watch Start a new thread and post a photo daily of any SAK 74mm or smaller ( you can switch it up daily ) for thirty (30) consecutive days. Start a thread with photos of at least eight different colored ALOX models in your collection Participate in a challenge thread and post a photo of a SAK Cybertool (any variant), Swisschamp, Champion or Toolchest for thirty (30) consecutive days. Participate  in a Challenge thread and post a photo of a LM Pocket Survival Tool for thirty (30) consecutive days. Start a new thread and post a photo of the discontinued sak/mt for thirty (30) consecutive days. Must update or add a page on SAKWiki Start a new thread and post a photo of the modified sak (scale swap not included) for thirty (30) consecutive days. Start a new thread and post a photo of a different SAK each day for thirty (30) consecutive days. Start a new thread with a photo of custom or non standard SAK scales in your collection Start a new thread demonstrating paracord knot tying Start a new thread showing photos of your outdoor cooking Start a thread with photos of at least five different colored ALOX models in your collection Start a new thread and post a photo of a fixed blade for thirty (30) consecutive days.

gb Offline Wspeed

  • *
  • Just Bananas
  • *************
    • Posts: 76,225
Re: Climber Lite with removable LED module
Reply #9 on: April 15, 2020, 11:14:36 PM
 :rofl:
fail to prepare prepare to fail
Merit Badges Must put something in order and provide link to the post. Join the brave and happy few, who choose a different path. Enter on the boulevard of broken dreams. Start a new thread with a photo of a modded knife or multitool with your EDC Must post a step by step pictorial of a knife or multitool modification (scale swap not included) For those who posted like a boss. Only for the 14th year Anniversary Challenge. Post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. You have one of your pictures in the 2020 calendar or in top three of the calendar poll in any month of the given year. Start a new thread and post a photo of the LM Crunch  Multitool for thirty (30) consecutive days. Start a new thread and post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Start a new thread and post a photo of a traditional folder for thirty (30) consecutive days. Start a new thread and post a photo of the leatherman (supertool, core, hacks) for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread with a photo showing the Swiss Army Knife   Toothpick being used in an unusual way. You have one of your pictures in the 2019 calendar or in top three of the calendar poll in any month of the given year. Participate in a challenge thread and post a photo of a SAK Cybertool (any variant), Swisschamp, Champion or Toolchest for thirty (30) consecutive days. Start a new thread demonstrating paracord knot tying Start a new thread with photos of your Buck knives in use Must start a thread with a photo of your camo SAK  Post a pic for Halloween of your pumpkin (or turnip or gourd or whatever you traditionally carve for Halloween!) being carved by any SAK, multitool, pocket or woods knife you may own!  Only available once a year Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread including a photo of shooting at least two (2) different airguns and at least one (1) photo of target (airguns)

se Offline kottskrapa

  • *
  • No Life Club
  • ******
    • Posts: 3,951
Re: Climber Lite with removable LED module
Reply #10 on: April 17, 2020, 08:53:13 AM
Nice mod! One of those that should be original som the beginning

[It's not failure if you learn something from it]

Merit Badges Start a new thread with photos of your hobo knives in use Participate in a challenge by carrying  a Combo Edged knife or Multitool and post a photo of it  for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread and post a photo daily of any SAK 74mm or smaller ( you can switch it up daily ) for thirty (30) consecutive days. Start a new thread with a photo of custom or non standard SAK scales in your collection Only for the 14th year Anniversary Challenge. Post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Start a new thread and post a photo of the keychain for thirty (30) consecutive days. Start a new thread with a photo showing the Swiss Army Knife   Toothpick being used in an unusual way. Start a thread with a photo of a repair you made with duct tape Start a new thread and post a photo of the modified sak (scale swap not included) for thirty (30) consecutive days. Start a new thread with a photo of a modded knife or multitool with your EDC Join the brave and happy few, who choose a different path. Enter on the boulevard of broken dreams. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Must start a thread with a photo of your birth year SAK Start a new thread and post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Must start a thread with a photo of your stayglow SAK Start a new thread with photos of your chainsaws Start a new thread and post a photo of the minimal sak (2 layers or fewer) for thirty (30) consecutive days. Start a new thread and post a photo of a flashlight as part of your EDC

nl Offline Reinier

  • *
  • Zombie Apprentice
  • ********
    • Posts: 10,495
  • \o/
Re: Climber Lite with removable LED module
Reply #11 on: April 17, 2020, 11:18:32 AM
This is an excellent mod!

Quote
What else could you clip into this new mounting point?

A USB stick? Like they do on the 58mm models?
A fork or spork, (would have to be longer though), like a hobo knife.
You should seriously visit vicfan.com. All the hoopy froods are doing it.
Merit Badges Must start new thread with photos of multitools (Magazine/Catalogue type photos) Start a new thread with a photo showing the Hook in use Start a new thread with photos of camping, including those showing preferred camping equipment Must sell something on EDCSource Must buy something on EDCSource Must update or add a page on SAKWiki Start a new thread with pictures of a Fish Scaler in use Start a new thread with a photo of your custom ALOX with scissors Start a new thread with photos of your astronomy gear with a multitool Start a new thread with a photo showing the Swiss Army Knife   Toothpick being used in an unusual way. Must start a thread with a photo of your stayglow SAK Must start a thread with a photo of your camo SAK Take part in the christmas pool or a rak type giveaway. Those wanting to say thank you for a rak may also nominate for the santa. Must start a thread showing a photo of at least three BO tools Start a thread with photos of at least twelve different colored ALOX models in your collection Start a thread with a photo of a repair you made with duct tape Start a new thread with a photo of custom or non standard SAK scales in your collection

ie Offline Don Pablo

  • *
  • Zombie Apprentice
  • ********
    • Posts: 15,329
  • Yoo-hoo, big summer blowout!
Re: Climber Lite with removable LED module
Reply #12 on: April 17, 2020, 12:16:18 PM
Brilliant and simple! :clap:
How easy is it to remove and insert?
Hooked, like everyone else. ;)

All hail the hook!
Merit Badges Start a new thread and post a photo of the pen for thirty (30) consecutive days. Participate in a Challenge thread and post a photo of  a Bladeless Multitool for 30 days Only for the 14th year Anniversary Challenge. Post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Start a new thread and post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Start a new thread and post a photo of the modified sak (scale swap not included) for thirty (30) consecutive days.

00 Offline Mechanickal

  • *
  • Zombie Apprentice
  • ********
    • Posts: 14,690
Re: Climber Lite with removable LED module
Reply #13 on: April 17, 2020, 05:14:08 PM
Neatly done! :tu:
Merit Badges Take part in the christmas pool or a rak type giveaway. Those wanting to say thank you for a rak may also nominate for the santa. Start a new thread and post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Start a thread with photos of at least twelve different colored ALOX models in your collection Start a new thread and post a photo of the 110 knife for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Must start a thread with a photo of your stayglow SAK Start a new thread with a photo showing the Hook in use Post your pocket dump photos then challenge two more members who must post their pocket dump photos within 24hrs for you to get the badge. Start a new thread with photos of your Buck knives in use Must put something in order and provide link to the post. Start a new thread with a photo of your custom ALOX with scissors Start a thread with photos of at least 1 MTO branded tool in your collection Must buy an item through the MTo Store Start a new thread with photos of your chainsaws Start a new thread with photos of your titanium gear with a multitool or sak Test,please ignore Must start a thread with a photo of your birth year SAK Start a thread with a photo of a repair you made with duct tape Start a new thread with a photo of custom or non standard SAK scales in your collection Start a new thread and post a photo of a flashlight as part of your EDC

za Offline Max Stone

  • *
  • Absolutely No Life Club
  • *******
    • Posts: 5,982
Re: Climber Lite with removable LED module
Reply #14 on: April 17, 2020, 10:11:15 PM
Thanks guys.  :hatsoff:

Yes, USB may be an option. Maybe even a small spork.

It’s really easy to clip on and off. Victorinox use a good quality plastic that’s not brittle, so it snaps over the pivot with a good positive click, and won’t fall out as it’s locked in when closed.

Here’s a video I did to show it better: https://m.youtube.com/watch?feature=youtu.be&v=6uFWWtP6HUo
Education is a journey that starts when you realize that knowing a little about something opens the door to the universe.
Merit Badges Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Must start a thread with a photo of at least three (3) of your watches Participate in a challenge thread and post a photo of a SAK Cybertool (any variant), Swisschamp, Champion or Toolchest for sixty (60) consecutive days. Must start a thread with a photo of your EDC watch Start a new thread and post a photo daily of any SAK 74mm or smaller ( you can switch it up daily ) for thirty (30) consecutive days. Start a thread with photos of at least eight different colored ALOX models in your collection Participate in a challenge thread and post a photo of a SAK Cybertool (any variant), Swisschamp, Champion or Toolchest for thirty (30) consecutive days. Participate  in a Challenge thread and post a photo of a LM Pocket Survival Tool for thirty (30) consecutive days. Start a new thread and post a photo of the discontinued sak/mt for thirty (30) consecutive days. Must update or add a page on SAKWiki Start a new thread and post a photo of the modified sak (scale swap not included) for thirty (30) consecutive days. Start a new thread and post a photo of a different SAK each day for thirty (30) consecutive days. Start a new thread with a photo of custom or non standard SAK scales in your collection Start a new thread demonstrating paracord knot tying Start a new thread showing photos of your outdoor cooking Start a thread with photos of at least five different colored ALOX models in your collection Start a new thread and post a photo of a fixed blade for thirty (30) consecutive days.

00 Offline Mechanickal

  • *
  • Zombie Apprentice
  • ********
    • Posts: 14,690
Re: Climber Lite with removable LED module
Reply #15 on: April 17, 2020, 10:40:33 PM
:dd:
:2tu:
Merit Badges Take part in the christmas pool or a rak type giveaway. Those wanting to say thank you for a rak may also nominate for the santa. Start a new thread and post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Start a thread with photos of at least twelve different colored ALOX models in your collection Start a new thread and post a photo of the 110 knife for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Must start a thread with a photo of your stayglow SAK Start a new thread with a photo showing the Hook in use Post your pocket dump photos then challenge two more members who must post their pocket dump photos within 24hrs for you to get the badge. Start a new thread with photos of your Buck knives in use Must put something in order and provide link to the post. Start a new thread with a photo of your custom ALOX with scissors Start a thread with photos of at least 1 MTO branded tool in your collection Must buy an item through the MTo Store Start a new thread with photos of your chainsaws Start a new thread with photos of your titanium gear with a multitool or sak Test,please ignore Must start a thread with a photo of your birth year SAK Start a thread with a photo of a repair you made with duct tape Start a new thread with a photo of custom or non standard SAK scales in your collection Start a new thread and post a photo of a flashlight as part of your EDC

ie Offline Don Pablo

  • *
  • Zombie Apprentice
  • ********
    • Posts: 15,329
  • Yoo-hoo, big summer blowout!
Re: Climber Lite with removable LED module
Reply #16 on: April 17, 2020, 11:04:00 PM
I luve it! :drool:
Hooked, like everyone else. ;)

All hail the hook!
Merit Badges Start a new thread and post a photo of the pen for thirty (30) consecutive days. Participate in a Challenge thread and post a photo of  a Bladeless Multitool for 30 days Only for the 14th year Anniversary Challenge. Post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Start a new thread and post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Start a new thread and post a photo of the modified sak (scale swap not included) for thirty (30) consecutive days.

za Offline Max Stone

  • *
  • Absolutely No Life Club
  • *******
    • Posts: 5,982
Re: Climber Lite with removable LED module
Reply #17 on: April 17, 2020, 11:19:45 PM
Thanks Don Pablo  :hatsoff: Now I just need to rebuild all my LED equipped SAKs.  :facepalm:
Education is a journey that starts when you realize that knowing a little about something opens the door to the universe.
Merit Badges Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Must start a thread with a photo of at least three (3) of your watches Participate in a challenge thread and post a photo of a SAK Cybertool (any variant), Swisschamp, Champion or Toolchest for sixty (60) consecutive days. Must start a thread with a photo of your EDC watch Start a new thread and post a photo daily of any SAK 74mm or smaller ( you can switch it up daily ) for thirty (30) consecutive days. Start a thread with photos of at least eight different colored ALOX models in your collection Participate in a challenge thread and post a photo of a SAK Cybertool (any variant), Swisschamp, Champion or Toolchest for thirty (30) consecutive days. Participate  in a Challenge thread and post a photo of a LM Pocket Survival Tool for thirty (30) consecutive days. Start a new thread and post a photo of the discontinued sak/mt for thirty (30) consecutive days. Must update or add a page on SAKWiki Start a new thread and post a photo of the modified sak (scale swap not included) for thirty (30) consecutive days. Start a new thread and post a photo of a different SAK each day for thirty (30) consecutive days. Start a new thread with a photo of custom or non standard SAK scales in your collection Start a new thread demonstrating paracord knot tying Start a new thread showing photos of your outdoor cooking Start a thread with photos of at least five different colored ALOX models in your collection Start a new thread and post a photo of a fixed blade for thirty (30) consecutive days.

ie Offline Don Pablo

  • *
  • Zombie Apprentice
  • ********
    • Posts: 15,329
  • Yoo-hoo, big summer blowout!
Re: Climber Lite with removable LED module
Reply #18 on: April 17, 2020, 11:43:20 PM
:rofl:
Hooked, like everyone else. ;)

All hail the hook!
Merit Badges Start a new thread and post a photo of the pen for thirty (30) consecutive days. Participate in a Challenge thread and post a photo of  a Bladeless Multitool for 30 days Only for the 14th year Anniversary Challenge. Post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Start a new thread and post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Start a new thread and post a photo of the modified sak (scale swap not included) for thirty (30) consecutive days.

pt Offline FInixNOver

  • Hero Member
  • *****
    • Posts: 825
Re: Climber Lite with removable LED module
Reply #19 on: April 18, 2020, 12:09:03 PM
This looks awesome!
Why haven't I thought of this before?

Great mod! :cheers:

Enviado do meu Redmi Note 5 através do Tapatalk

Merit Badges Start a new thread and post a photo daily of any SAK 74mm or smaller ( you can switch it up daily ) for thirty (30) consecutive days. Start a new thread and post a photo of a fixed blade for thirty (30) consecutive days. Start a new thread with a photo of your custom ALOX with scissors Start a new thread with a photo of a modded knife or multitool with your EDC Start a new thread and post a photo of a flashlight as part of your EDC

za Offline Max Stone

  • *
  • Absolutely No Life Club
  • *******
    • Posts: 5,982
Re: Climber Lite with removable LED module
Reply #20 on: April 18, 2020, 04:13:07 PM
Thanks FInixNOver  :hatsoff:
Education is a journey that starts when you realize that knowing a little about something opens the door to the universe.
Merit Badges Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Must start a thread with a photo of at least three (3) of your watches Participate in a challenge thread and post a photo of a SAK Cybertool (any variant), Swisschamp, Champion or Toolchest for sixty (60) consecutive days. Must start a thread with a photo of your EDC watch Start a new thread and post a photo daily of any SAK 74mm or smaller ( you can switch it up daily ) for thirty (30) consecutive days. Start a thread with photos of at least eight different colored ALOX models in your collection Participate in a challenge thread and post a photo of a SAK Cybertool (any variant), Swisschamp, Champion or Toolchest for thirty (30) consecutive days. Participate  in a Challenge thread and post a photo of a LM Pocket Survival Tool for thirty (30) consecutive days. Start a new thread and post a photo of the discontinued sak/mt for thirty (30) consecutive days. Must update or add a page on SAKWiki Start a new thread and post a photo of the modified sak (scale swap not included) for thirty (30) consecutive days. Start a new thread and post a photo of a different SAK each day for thirty (30) consecutive days. Start a new thread with a photo of custom or non standard SAK scales in your collection Start a new thread demonstrating paracord knot tying Start a new thread showing photos of your outdoor cooking Start a thread with photos of at least five different colored ALOX models in your collection Start a new thread and post a photo of a fixed blade for thirty (30) consecutive days.

us Offline Aloha

  • Global Moderator
  • *
  • Point Of No Return
  • *
    • Posts: 31,235
Re: Climber Lite with removable LED module
Reply #21 on: April 18, 2020, 04:53:28 PM
 :hatsoff:  Well done. 
Esse Quam Videri
Merit Badges Start a new thread and post a photo of the pen for thirty (30) consecutive days. Start a new thread and post a photo of a traditional folder for thirty (30) consecutive days. Take part in the christmas pool or a rak type giveaway. Those wanting to say thank you for a rak may also nominate for the santa. Must start a thread showing a photo of at least eight BO tools Start a new thread showing photos of your outdoor cooking Must have a review written in the proper format and posted on the Main Site Start a new thread and post a picture of fire making kit or fire with a multitool Start a new thread with photos of camping, including those showing preferred camping equipment Start a new thread and post a photo of a flashlight as part of your EDC Start a thread with photos of at least 5 different Juice models in your collection Start a new thread with photos of a Japanese made PST in your collection Start a thread with a photo of at least ten OPT's in your collection

ca Offline armi101

  • Full Member
  • ***
    • Posts: 143
Re: Climber Lite with removable LED module
Reply #22 on: April 18, 2020, 06:14:10 PM
Great idea.
Merit Badges Must post a step by step pictorial of a knife or multitool modification (scale swap not included)

za Offline Max Stone

  • *
  • Absolutely No Life Club
  • *******
    • Posts: 5,982
Re: Climber Lite with removable LED module
Reply #23 on: April 18, 2020, 06:25:40 PM
Thanks Aloha, armi101  :hatsoff:
Education is a journey that starts when you realize that knowing a little about something opens the door to the universe.
Merit Badges Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Must start a thread with a photo of at least three (3) of your watches Participate in a challenge thread and post a photo of a SAK Cybertool (any variant), Swisschamp, Champion or Toolchest for sixty (60) consecutive days. Must start a thread with a photo of your EDC watch Start a new thread and post a photo daily of any SAK 74mm or smaller ( you can switch it up daily ) for thirty (30) consecutive days. Start a thread with photos of at least eight different colored ALOX models in your collection Participate in a challenge thread and post a photo of a SAK Cybertool (any variant), Swisschamp, Champion or Toolchest for thirty (30) consecutive days. Participate  in a Challenge thread and post a photo of a LM Pocket Survival Tool for thirty (30) consecutive days. Start a new thread and post a photo of the discontinued sak/mt for thirty (30) consecutive days. Must update or add a page on SAKWiki Start a new thread and post a photo of the modified sak (scale swap not included) for thirty (30) consecutive days. Start a new thread and post a photo of a different SAK each day for thirty (30) consecutive days. Start a new thread with a photo of custom or non standard SAK scales in your collection Start a new thread demonstrating paracord knot tying Start a new thread showing photos of your outdoor cooking Start a thread with photos of at least five different colored ALOX models in your collection Start a new thread and post a photo of a fixed blade for thirty (30) consecutive days.

pt Offline pfrsantos

  • *
  • Absolute Zombie Club
  • *********
    • Posts: 23,961
  • Oxygen and magnesium toghether?! OMg!
Re: Climber Lite with removable LED module
Reply #24 on: April 21, 2020, 06:37:11 PM
Quote from: RF52 on April 15, 2020, 10:25:35 PM
Very nice! Great idea and good job :hatsoff:

Sent fra min FRD-L09 via Tapatalk

 :iagree:

Well done! Have you patented it? Vic is going to be stealing that idea!

 :cheers: :tu:
________________________________
It is just a matter of time before they add the word “Syndrome” after my last name.

I don't have OCD, I have OCDEFGHIJKLMNOPQRSTUVWXYZ.

I'd give my right arm to be ambidextrous.

Eff the ineffable, scrut the inscrutable.

IYCRTYSWTMTFOT


pt Offline pfrsantos

  • *
  • Absolute Zombie Club
  • *********
    • Posts: 23,961
  • Oxygen and magnesium toghether?! OMg!
Re: Climber Lite with removable LED module
Reply #25 on: April 21, 2020, 06:37:52 PM
Quote from: Don Pablo on April 17, 2020, 12:16:18 PM
Brilliant and simple! :clap:
How easy is it to remove and insert?



 :D :D :D :D
________________________________
It is just a matter of time before they add the word “Syndrome” after my last name.

I don't have OCD, I have OCDEFGHIJKLMNOPQRSTUVWXYZ.

I'd give my right arm to be ambidextrous.

Eff the ineffable, scrut the inscrutable.

IYCRTYSWTMTFOT


za Offline Max Stone

  • *
  • Absolutely No Life Club
  • *******
    • Posts: 5,982
Re: Climber Lite with removable LED module
Reply #26 on: April 21, 2020, 11:51:59 PM
Quote from: pfrsantos on April 21, 2020, 06:37:11 PM
:iagree:

Well done! Have you patented it? Vic is going to be stealing that idea!

 :cheers: :tu:

 :hatsoff:
I think they already did a similar system on the Rescue Tool...so it’s not so original. Just not a common feature for Vic to have removable tools.
Education is a journey that starts when you realize that knowing a little about something opens the door to the universe.
Merit Badges Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Must start a thread with a photo of at least three (3) of your watches Participate in a challenge thread and post a photo of a SAK Cybertool (any variant), Swisschamp, Champion or Toolchest for sixty (60) consecutive days. Must start a thread with a photo of your EDC watch Start a new thread and post a photo daily of any SAK 74mm or smaller ( you can switch it up daily ) for thirty (30) consecutive days. Start a thread with photos of at least eight different colored ALOX models in your collection Participate in a challenge thread and post a photo of a SAK Cybertool (any variant), Swisschamp, Champion or Toolchest for thirty (30) consecutive days. Participate  in a Challenge thread and post a photo of a LM Pocket Survival Tool for thirty (30) consecutive days. Start a new thread and post a photo of the discontinued sak/mt for thirty (30) consecutive days. Must update or add a page on SAKWiki Start a new thread and post a photo of the modified sak (scale swap not included) for thirty (30) consecutive days. Start a new thread and post a photo of a different SAK each day for thirty (30) consecutive days. Start a new thread with a photo of custom or non standard SAK scales in your collection Start a new thread demonstrating paracord knot tying Start a new thread showing photos of your outdoor cooking Start a thread with photos of at least five different colored ALOX models in your collection Start a new thread and post a photo of a fixed blade for thirty (30) consecutive days.

pt Offline pfrsantos

  • *
  • Absolute Zombie Club
  • *********
    • Posts: 23,961
  • Oxygen and magnesium toghether?! OMg!
Re: Climber Lite with removable LED module
Reply #27 on: April 22, 2020, 01:16:48 PM
Quote from: Max Stone on April 21, 2020, 11:51:59 PM
:hatsoff:
I think they already did a similar system on the Rescue Tool...so it’s not so original. Just not a common feature for Vic to have removable tools.

Yeah, awlso with the USB models. Still, it's the first with the LED.

 :cheers: :tu:
________________________________
It is just a matter of time before they add the word “Syndrome” after my last name.

I don't have OCD, I have OCDEFGHIJKLMNOPQRSTUVWXYZ.

I'd give my right arm to be ambidextrous.

Eff the ineffable, scrut the inscrutable.

IYCRTYSWTMTFOT


za Offline Max Stone

  • *
  • Absolutely No Life Club
  • *******
    • Posts: 5,982
Re: Climber Lite with removable LED module
Reply #28 on: April 22, 2020, 11:11:08 PM
Well, I email Victorinox with a pic and link to the video...  :popcorn:
Education is a journey that starts when you realize that knowing a little about something opens the door to the universe.
Merit Badges Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Must start a thread with a photo of at least three (3) of your watches Participate in a challenge thread and post a photo of a SAK Cybertool (any variant), Swisschamp, Champion or Toolchest for sixty (60) consecutive days. Must start a thread with a photo of your EDC watch Start a new thread and post a photo daily of any SAK 74mm or smaller ( you can switch it up daily ) for thirty (30) consecutive days. Start a thread with photos of at least eight different colored ALOX models in your collection Participate in a challenge thread and post a photo of a SAK Cybertool (any variant), Swisschamp, Champion or Toolchest for thirty (30) consecutive days. Participate  in a Challenge thread and post a photo of a LM Pocket Survival Tool for thirty (30) consecutive days. Start a new thread and post a photo of the discontinued sak/mt for thirty (30) consecutive days. Must update or add a page on SAKWiki Start a new thread and post a photo of the modified sak (scale swap not included) for thirty (30) consecutive days. Start a new thread and post a photo of a different SAK each day for thirty (30) consecutive days. Start a new thread with a photo of custom or non standard SAK scales in your collection Start a new thread demonstrating paracord knot tying Start a new thread showing photos of your outdoor cooking Start a thread with photos of at least five different colored ALOX models in your collection Start a new thread and post a photo of a fixed blade for thirty (30) consecutive days.

pt Offline pfrsantos

  • *
  • Absolute Zombie Club
  • *********
    • Posts: 23,961
  • Oxygen and magnesium toghether?! OMg!
Re: Climber Lite with removable LED module
Reply #29 on: April 23, 2020, 05:10:38 PM
Quote from: Max Stone on April 22, 2020, 11:11:08 PM
Well, I email Victorinox with a pic and link to the video...  :popcorn:

:popcorn:

Well, you're either receiving a nice complementary SAK or a lawsuit...

 :whistle:



 :D :D :D :D
________________________________
It is just a matter of time before they add the word “Syndrome” after my last name.

I don't have OCD, I have OCDEFGHIJKLMNOPQRSTUVWXYZ.

I'd give my right arm to be ambidextrous.

Eff the ineffable, scrut the inscrutable.

IYCRTYSWTMTFOT


Pages: 1 2   Go Up
 

Donations
Operational Funds

Help us keep the Unworkable working!
Donate with PayPal!
May Goal: $300.00
Due Date: May 31
Total Receipts: $86.45
PayPal Fees: $5.07
Net Balance: $81.38
Below Goal: $218.62
Site Currency: USD
27% 
May Donations

Community Links
Multitool.org
Multitool Gallery
Multitool Encyclopedia
SAKWiki
Swiss Army Knights

Powered by EzPortal