Multitool.org Forum
Tool Talk => Reviews => Topic started by: Zack on February 03, 2010, 02:21:00 AM
-
Octane.
(http://i799.photobucket.com/albums/yy277/zrfraser/DSC_7506.jpg)
(http://i799.photobucket.com/albums/yy277/zrfraser/DSC_7507.jpg)
The Octane is a light/medium duty tool with their tried and true sliding plier head design. On board it carries a: Plier head, hard wire notch, bottle opener, CE OH knife blade, clamshell opener, flat head driver, and Phillips driver.
Thoughts:
Pliers: I am not a huge fan of the sliding plier design, because it makes it very difficult to get to the tools in the handles, and limits the tools you can fit. The plier head on mine is very loose, with a lot of side to side and vertical play. They lock fine but the wobble is something I just don’t like in my pliers. Hard wire notch is typical quality and handled coat hanger with not too much effort.
(http://i799.photobucket.com/albums/yy277/zrfraser/DSC_7508.jpg)
Bottle opener: This is a new take on multitool bottle openers. You open the pliers place the bottle opener around the cap and pull. This design works fairly well, and pretty easy to deploy due to the sliding pliers.
(http://i799.photobucket.com/albums/yy277/zrfraser/DSC_7517.jpg)
Knife: Knife is a modified sheepsfoot with a combo edge. The liner lock done on mine is horrible, and hopefully will be revamped in later designs and models. The liner travels to far on the tang, meaning as the tang wears with the lock, the knife will develop play, as there is no room for wear. The liner is also not very long; it is merely a tab that clicks into the handle, which doesn’t look very sturdy. Time will tell how it holds up.
(http://i799.photobucket.com/albums/yy277/zrfraser/DSC_7514.jpg)
(http://i799.photobucket.com/albums/yy277/zrfraser/DSC_7516.jpg)
Clamshell opener: This is probably one of the best innovations that have come along in multitools in quite some time. This one is a pull type opener, which is different from the Strata’s push type. I must say it works wonderfully. Mainly poke the tip in the clamshell and pull. It also makes a great box opener, grout ripper, fingernail cleaner and general poker/scraper. This is one of the best aspects of the tool.
(http://i799.photobucket.com/albums/yy277/zrfraser/DSC_7513.jpg)
Flat head driver: Pretty basic, works as intended.
(http://i799.photobucket.com/albums/yy277/zrfraser/DSC_7512.jpg)
(http://i799.photobucket.com/albums/yy277/zrfraser/DSC_7511.jpg)
Phillips driver: Finally a 3D driver from Gerber. Works great, decent length, and thick. It’s not slippery as long as the head is the right size, and I’m glad in the direction Gerber is going regarding the 3D Phillips driver.
(http://i799.photobucket.com/albums/yy277/zrfraser/DSC_7510.jpg)
Another thing I really like in this tool is the pocket clip. Its no secret that I don’t like the Skeletool pocket clip, but this one is nice. It’s a low riding clip with just the right amount of tension and fairly inconspicuous.
Overall: For a light duty tool or someone looking for something different from the Leatherman Juice and Skeletool range, this is a nice tool. The blade is a little off putting, due to the liner lock, but most of us carry a dedicated knife anyway. Will this replace your Wave or Spirit? Probably not, but for a lightweight EDC tool I think it’s worth a look.
Note: A Leatherman Charge Ti was used in all pictures for size comparison only.
-
For some reason the blade shape really speaks to me, very nice. :) Thanks for the review and excellent pics. :salute:
-
I like the shape too, and its very smooth to open, I just wish the liner lock was made better.
-
great review man :salute: and great pics too :tu:
-
Gotta know...does this pinch the hand less than the older sliding-head Gerbers (minus the gimmicky Flik)?
-
Hasn't pinched me yet...knock on wood.
-
Thx for the review Zack :tu: how did you open the clamshell with the tool inside? :think: :D
-
I used the Ultimate clamshell opener....My Emerson CQC7
-
I was opening my Fuse Monarch 200 combo clamshell today (gave away the flashlight to a girl at work when I saw the type of battery it uses, kept the Fuse as work tool) and not wanting to ruin any of my blades used work scissors instead and think ruined them in the process :twak: :D
-
How would a blade of any quality be ruined by plastic?
-
Not ruined you're right, but dulled, it was some tough plastic :D and I went around the edges trying to preserve the paper intact.
-
Nice review Zack and great pics as well :tu:
-
Another fantastic review, Zack! :tu:
-
I think there's a lot more to this tool than first meets the eye. And its a big improvement over Gerber offerings of the last few years.
The tool itself is relatively small, yet the knife blade is comparitively long. And it operates smoothly one hand opening. And those screwdrivers, notice how long they are? Good job Gerber I'll say. :salute:
-
Fine review and some nice pictures. :tu: I may have to check out the Octane.
-
For some reason the blade shape really speaks to me, very nice. :) Thanks for the review and excellent pics. :salute:
Me too, it look's like a lovely slicer :)
-
Finally, some nice sized tools.
That was always my biggest issue with Gerber...these little tiny tools that were more for show then use.
I might have to add this one to the collection whenever I can get one.
-
Spotted an Octane at Cabelas today, came here to look for a review, and BOOM, here it is. Well written, great pics & good info.
Makes me want to return and pick one up. Thanks. :cheers:
-
Thats MTO for ya. I think we might have been the first to get some up close pictures of the tool. Its a great lighweight tool, even if you just get it for the clamshell opener.
-
I went back to Cabelas yesterday and grabbed the Octane. I am carrying it today in a Buck "debadged" nylon sheath that Cabelas also had. One thing cool about the sheath carry is when pulling out the Octane, the pliers are pulled out as well when removing the tool from the sheath. I like the knife blade design a lot, but not the blade stop so much as mentioned in the review.
-
A video clip (http://www.youtube.com/watch?v=0DTUezf5u7I) about the Octane on YouTube mentions "USA quality." Is the Gerber Octane made in USA? If not, where.
Thanks.
-
A video clip (http://www.youtube.com/watch?v=0DTUezf5u7I) about the Octane on YouTube mentions "USA quality." Is the Gerber Octane made in USA? If not, where.
Thanks.
I thought it was made in China... :think:
-
99% sure its made in china as well. I don't know...I'll see if I can find the packaging for it.
-
So how's everyone getting along with their Octane's?
I'm thinking of buying one, as I'm in need of a light edc with a clip to pants carry.
I will be using the pliers quite often throughout the day so the sliding plier head
is a plus. Thanks.
-
Mine sees a fair bit of use and still looks brand new.
Def
-
Thanks, I think I'll pick one up. I have a couple of sideclips which I quite like but
you have break them open anytime you need pliers and knife etc.
-
The only thing that worries me a bit is that the plier head doesn't lock when
closed? I'm afraid I might have the same problem with mine as the other
chap had stated whilst carrying around the head tended to slip into the
partially deployed or fully deployed state?
-
The Octane is my favorite non-400 non-600 Gerber. :salute: It is not what I consider to be a "heavy-duty" tool though. More of a competitor to the Skeletool really, due to its construction.
The pliers will slip out while carrying the Octane pocket clipped. :-\ I think it was a bit of an oversight that there is not a locking notch to keep the pliers in the closed position. Although other sliding head Gerbers don't have the "closed" notch either, they have stronger plunger springs, which keep the head from sliding on its own.
-
So it slides out by itself when clipped to pocket?
-
It can. :( Which isn't a huge deal if you clip-carry with the tool inside your pocket, because it can't really go anywhere. But if you clip-carry with the tool outside your pocket, and the clip inside - or clipped on a belt - then the head will eventually slide out. :( And once it is slid out fully, the handles flop open, and.... :( :( Not good. :(
Gerber could cure this easily. Either put stiffer springs in the little plungers, or stamp a locking notch at both ends of the slideway:
(http://img.photobucket.com/albums/v307/jooliesews/Bobbys/Octanelockingnotches.jpg)
-
Correct me if I'm wrong Bob but if they put notches in on the closed position, wouldn't they be unable to be flicked open? Not saying that would be terrible, but it might be why Gerber don't have them there.
-
That's one of the reason I got rid of the flik, head comes out through the open bottom sheath. Looks like I'll stick with my skeletool when I want a clipped light weight tool.
Don't know about the price elsewhere but here it's same as skeletool, I mean if you are going to make it in China, at least pass some of the saving to consumers, right?
-
I wondered that for a second Gareth, but that really shouldn't be a factor. Check out the video at about 1:30. Even if the plungers were engaged in notches, the pliers would still slide open the same:
A video clip (http://www.youtube.com/watch?v=0DTUezf5u7I) about the Octane on YouTube mentions "USA quality." Is the Gerber Octane made in USA? If not, where.
Thanks.
-
I wondered that for a second Gareth, but that really shouldn't be a factor. Check out the video at about 1:30. Even if the plungers were engaged in notches, the pliers would still slide open the same:
A video clip (http://www.youtube.com/watch?v=0DTUezf5u7I) about the Octane on YouTube mentions "USA quality." Is the Gerber Octane made in USA? If not, where.
Thanks.
Ah yes, that would still work. :)
-
So, has anyone tried notching some slot's into the handles to prevent them from
opening when closed? Flicking isn't important to me at least as you can still
open them with one hand by pressing the pins and giving it a shake downwards.
Anyhow, I was wondering about the mod on the Octane? Thanks.
-
So, has anyone tried notching some slot's into the handles to prevent them from
opening when closed? Flicking isn't important to me at least as you can still
open them with one hand by pressing the pins and giving it a shake downwards.
Anyhow, I was wondering about the mod on the Octane? Thanks.
I'm sure it would work, but I haven't tried it. :-\
-
I recall someone here did it on another gerber, and it works fine.
The square corner might be difficult to make with average household tools though.
-
Thanks guys. I would imagine a file might work ok on it?
Anyhow, I'm back and forth with either the octane or the
Freestyle. I only need pliers and a knife for this carry.
-
MEC carries both, check them out next time you are in Vancouver.
Personally I like the sliding head since I use pliers on a MT the most, and my EDC (in bag, not person though) is a MP400.
-
Thanks Jz, that was my plan. :)
-
It is a compact tool, which is nice but the liner lock on the knife is weak imo. Mine bent just a little as I played with it. I didn't push against it hard. I just lightly pushed against it to check the lockup.
-
Yeah I noticed that as well about the liner locks being thin from vid's and pic's.
-
After reading the Gerber Episodes post, I had to get one. I actually found one on Amazon, NIB.
Even after reading lots of reviews (about 50/50) I still ordeded it. My Octane will be here next week. I will let you know what I think.
This is for "light" days around the house. I have a Centre Line for work.
-
After reading the Gerber Episodes post, I had to get one. I actually found one on Amazon, NIB.
Even after reading lots of reviews (about 50/50) I still ordeded it. My Octane will be here next week. I will let you know what I think.
This is for "light" days around the house. I have a Centre Line for work.
That's really the bottom line on the Octane- it is a light duty tool, similar to the Skeletool or Reactor. If you ask it to do heavy work then you are going to have a bad time. It will handle some, but to pound on it every day like it was a heavy duty tool and expect it to keep up is asking too much. It's like buying one of those new little hatchbacks and complaining that it has trouble hauling your horse trailer around.
Def
-
After reading the Gerber Episodes post, I had to get one. I actually found one on Amazon, NIB.
Even after reading lots of reviews (about 50/50) I still ordeded it. My Octane will be here next week. I will let you know what I think.
This is for "light" days around the house. I have a Centre Line for work.
That's really the bottom line on the Octane- it is a light duty tool, similar to the Skeletool or Reactor. If you ask it to do heavy work then you are going to have a bad time. It will handle some, but to pound on it every day like it was a heavy duty tool and expect it to keep up is asking too much. It's like buying one of those new little hatchbacks and complaining that it has trouble hauling your horse trailer around.
Def
Speaking of Skeletool, I have this coming next week.
-
Despite the issues I had with my Octane's screwdrivers (I've got a video on it somewhere) I still really like the Octane. Grants car simile is very apt though, it's not a tank. That said I used it in my Building Maintenance job quite often when I first got it and I don't remember it missing a beat. :)
-
Despite the issues I had with my Octane's screwdrivers (I've got a video on it somewhere) I still really like the Octane. Grants car simile is very apt though, it's not a tank. That said I used it in my Building Maintenance job quite often when I first got it and I don't remember it missing a beat. :)
First hand use, appreciate the info. I will post back when I get mine.
-
After reading the Gerber Episodes post, I had to get one. I actually found one on Amazon, NIB.
Even after reading lots of reviews (about 50/50) I still ordeded it. My Octane will be here next week. I will let you know what I think.
This is for "light" days around the house. I have a Centre Line for work.
That's really the bottom line on the Octane- it is a light duty tool, similar to the Skeletool or Reactor. If you ask it to do heavy work then you are going to have a bad time. It will handle some, but to pound on it every day like it was a heavy duty tool and expect it to keep up is asking too much. It's like buying one of those new little hatchbacks and complaining that it has trouble hauling your horse trailer around.
Def
Speaking of Skeletool, I have this coming next week.
Nice pretty red one!
I didn't go for any of the fancy colored versions myself, although I do have a coyote tan one. I guess I'm a bit of a sucker for military colors. After all, my Jeep is Commando Green and a good percentage of my wardrobe is olive drab or coyote tan. :facepalm:
Def
-
The Octane is still one of my favorites, and gets a lot of carry time still. It's the only tool I've bought two of, well, for myself I mean.
Word of advice: baby the pliers. Hard use will somehow warp them, and cause them to not open/close without binding
-
The Octane is still one of my favorites, and gets a lot of carry time still. It's the only tool I've bought two of, well, for myself I mean.
Word of advice: baby the pliers. Hard use will somehow warp them, and cause them to not open/close without binding
Thanks for the warning. I really like my Octane. It is my light day tool or a second carry on work day; or my Skeletool.
-
Man 9 years later I find out about the octane, want one, and there are none to be found :(
Charles.