Multitool.org Forum
Trade Forums => Tools Needed => Topic started by: JustinCase on October 04, 2018, 09:56:14 PM
-
Hi guys!
Any chance of someone having a spare PST pivot with screw? I was taking apart my good old '95 PST for a clean up job and both, (pivot & screw) rolled down behind the work bench which, by the way, it's too heavy to move :poh:....Please let me know, I will buy it from you.
Thanks in advance! :salute:
(https://imageshack.com/a/img923/5639/4Mkx7a.jpg)
-
I have a few knurled posts and screws here but I don't know if any came from a PST.
Have you got a caliper? That might help narrow it down some.
Alternatively I could measure the ones I have here but that will have to wait till I get home.
-
I have a few knurled posts and screws here but I don't know if any came from a PST.
Have you got a caliper? That might help narrow it down some.
Alternatively I could measure the ones I have here but that will have to wait till I get home.
I did a quick check with my calipers and the measurements are approximately 12.19mm high x 4.89mm thick. The screw is about 7.63mm long. Well, at least you will have an idea.
(https://imageshack.com/a/img924/4317/n7NmcT.jpg)
-
I've got one you could have, but unfortunately I'm at the other end of the country at the moment. I could ask Mrs Fuzzy to send it?
-
I've got one you could have, but unfortunately I'm at the other end of the country at the moment. I could ask Mrs Fuzzy to send it?
Appreciate it, but don't want to make it inconvenient for anyone. Probably someone from the US will come along.
Thank you :tu:
-
I have a few knurled posts and screws here but I don't know if any came from a PST.
Have you got a caliper? That might help narrow it down some.
Alternatively I could measure the ones I have here but that will have to wait till I get home.
I did a quick check with my calipers and the measurements are approximately 12.19mm high x 4.89mm thick. The screw is about 7.63mm long. Well, at least you will have an idea.
(https://imageshack.com/a/img924/4317/n7NmcT.jpg)
I've got one here that should work.
Like Fuzz though I'm in another country...
If nobody states side shows up then holler and I'll send it over.
-
I have a few knurled posts and screws here but I don't know if any came from a PST.
Have you got a caliper? That might help narrow it down some.
Alternatively I could measure the ones I have here but that will have to wait till I get home.
I did a quick check with my calipers and the measurements are approximately 12.19mm high x 4.89mm thick. The screw is about 7.63mm long. Well, at least you will have an idea.
(https://imageshack.com/a/img924/4317/n7NmcT.jpg)
I've got one here that should work.
Like Fuzz though I'm in another country...
If nobody states side shows up then holler and I'll send it over.
Thank you zoidberg. How much is postage?
-
Let me look I'm pretty sure I've got some.
Edit:
Yep I've got one. Unless you already got sorted PM me your address :tu:
-
Great! PM sent.
-
Thanks very much Steve. I owe you one buddy :cheers:....and the same goes for Fuzz and zoid, thank you guys for the offer :salute:
-
Nice one Steve. :salute: You're quite welcome JC! :cheers:
-
Sorry Justin, life got busy and I am only just getting back to this now.
Thanks Steve for the save. :cheers:
-
Hey Steve,
It's here, arrived today. Now good old PST is back in action!... :woohoo:
Mods, please close. Thank you! :salute:
-
Glad to help :cheers: