Multitool.org Forum
+-

Hello Lurker! Remove this ad and much more by logging in.


Leatherman case questions

cortiz1679 · 37 · 5363
« previous next »
Pages: 1 2   Go Down

Offline cortiz1679

  • Full Member
  • ***
    • Posts: 102
Re: Leatherman case questions
Reply #30 on: September 22, 2007, 03:00:00 AM
What other neat accessories yall holding out on!

ca Offline Grant Lamontagne

  • Head Turd Polisher
  • Administrator
  • *
  • Just Bananas
  • *
    • Posts: 65,944
  • Optimum instrumentum est inter aures
Re: Leatherman case questions
Reply #31 on: September 22, 2007, 03:19:50 AM
Ask him about the removable bit driver awl!  :pok:

Def
Leave the dents as they are- let your belongings show their scars as proudly as you do yours.
Merit Badges Take part in the christmas pool or a rak type giveaway. Those wanting to say thank you for a rak may also nominate for the santa. For those who posted like a boss. Post your pocket dump photos then challenge two more members who must post their pocket dump photos within 24hrs for you to get the badge. Start a new thread with a photo of custom or non standard SAK scales in your collection Start a thread with a photo of a repair you made with duct tape Start a new thread including a photo of shooting at least two (2) different airguns and at least one (1) photo of target (airguns) Start a thread with a photo of at least ten OPT's in your collection Must start a thread with a photo of at least five (5) of your watches Must start a thread showing a photo of at least eight BO tools Start a thread with photos of at least 1 MTO branded tool in your collection Start a new thread showing photos of your outdoor cooking Must have a review written in the proper format and posted on the Main Site Start a new thread with a photo of at least 5 different Charge models in your collection

us Offline J-sews

  • Admin Team
  • *
  • Absolute Zombie Club
  • *
    • Posts: 23,220
Re: Leatherman case questions
Reply #32 on: September 22, 2007, 12:28:03 PM
Hey! Funny you should mention that. I had an opportunity to use that awl bit earlier this week. I was drilling holes in a piece of sheet metal (with a power drill) but the drill bit kept wandering off my start spot. I used the awl to make little dimples for the drill bit to start on.

In order to be certain of having the right tool for every job.........one must first acquire a lot of tools

ca Offline Grant Lamontagne

  • Head Turd Polisher
  • Administrator
  • *
  • Just Bananas
  • *
    • Posts: 65,944
  • Optimum instrumentum est inter aures
Re: Leatherman case questions
Reply #33 on: September 22, 2007, 12:53:05 PM
Yup, that's the one I meant! :P

Def
Leave the dents as they are- let your belongings show their scars as proudly as you do yours.
Merit Badges Take part in the christmas pool or a rak type giveaway. Those wanting to say thank you for a rak may also nominate for the santa. For those who posted like a boss. Post your pocket dump photos then challenge two more members who must post their pocket dump photos within 24hrs for you to get the badge. Start a new thread with a photo of custom or non standard SAK scales in your collection Start a thread with a photo of a repair you made with duct tape Start a new thread including a photo of shooting at least two (2) different airguns and at least one (1) photo of target (airguns) Start a thread with a photo of at least ten OPT's in your collection Must start a thread with a photo of at least five (5) of your watches Must start a thread showing a photo of at least eight BO tools Start a thread with photos of at least 1 MTO branded tool in your collection Start a new thread showing photos of your outdoor cooking Must have a review written in the proper format and posted on the Main Site Start a new thread with a photo of at least 5 different Charge models in your collection

Offline cortiz1679

  • Full Member
  • ***
    • Posts: 102
Re: Leatherman case questions
Reply #34 on: September 23, 2007, 05:36:46 PM
what are the holes for?
can some1 tell me why the bit extender by LM is $12

us Offline J-sews

  • Admin Team
  • *
  • Absolute Zombie Club
  • *
    • Posts: 23,220
Re: Leatherman case questions
Reply #35 on: September 23, 2007, 07:56:43 PM
Quote from: cortiz1679 on September 23, 2007, 05:36:46 PM
what are the holes for?
can some1 tell me why the bit extender by LM is $12

The holes in the bits are leftover from the spade drills I made them from:  http://forum.multitool.org/index.php/topic,1111.0.html

The Leatherman Bit Extender costs $12 because they figured no one would pay $13 for it!  :P

(Seriously, you could get a generic extension at a hardware store and grind it down yourself for less money)
In order to be certain of having the right tool for every job.........one must first acquire a lot of tools

Offline cortiz1679

  • Full Member
  • ***
    • Posts: 102
Re: Leatherman case questions
Reply #36 on: September 23, 2007, 10:58:32 PM
That’s genius! i would of never thought about the spade thing!

Pages: 1 2   Go Up
 

Donations
Operational Funds

Help us keep the Unworkable working!
Donate with PayPal!
April Goal: $300.00
Due Date: Apr 30
Total Receipts: $158.99
PayPal Fees: $9.20
Net Balance: $149.79
Below Goal: $150.21
Site Currency: USD
50% 
April Donations

Community Links
Multitool.org
Multitool Gallery
Multitool Encyclopedia
SAKWiki
Swiss Army Knights

Powered by EzPortal