Multitool.org Forum
+-

Hello Lurker! Remove this ad and much more by logging in.


Adding an Awl (Reamer) to a Wave and a Blast

Corso · 20 · 2721
« previous next »
Pages: 1   Go Down

us Offline Corso

  • Full Member
  • ***
    • Posts: 135
Adding an Awl (Reamer) to a Wave and a Blast
on: August 10, 2018, 12:04:03 AM
I have found using the micro-driver tool awkward to manipulate when they are attached to our multitools, so I decided to delete them from the Wave and Blast tools and add an awl from the Rebar into each instead.

The Blast mod proved to be very simple.  First I used 2 Juice S2s to remove the pivot from the Blast.  I only backed out the pivot as much as needed to remove the saw, washers and micro-driver, then installed the awl and replaced the washers and saw.  I re-tightened the pivot until it felt right.  The tools lock just like normal, no clearance or closing issues with the plier head. 



Even the nail nicks are staggered like it was meant to be that way.






The Wave was a little more involved as I wanted to put the awl on the outside of the tool stack and have the flat driver in the middle to use as more of a pry bar.  The issue is that the flat driver is too long in the middle as it interferes with the little plier rest tab.

To remedy this I removed the flat driver and micro-driver and then taped them together so I could eyeball how much I would need to shorten the flat driver.  I used a Sharpie to mark the end of the flat driver to be removed.



Once shortened, I squared up the edges of the flat driver and reassembled the stack in the order I wanted and then tested the fit.  The flat driver now comes to within a hair’s breadth of the plier rest tab without actually touching it.  It also sits about 1mm proud of the tab.  The pliers still close fully with no further mods needed to the flat driver.






I plan to use the micro-driver “off tool” with a lanyard through the pivot hole.  Much easier for me to use that way.  Here is the other MT I used to persuade the pivots to budge.  Hope this was helpful!

« Last Edit: August 10, 2018, 12:06:55 AM by Corso »

gb Offline Wspeed

  • *
  • Just Bananas
  • *************
    • Posts: 76,225
Re: Adding an Awl (Reamer) to a Wave and a Blast
Reply #1 on: August 10, 2018, 12:11:05 AM
Nice mod Corso :like: :like: :tu:
fail to prepare prepare to fail
Merit Badges Must put something in order and provide link to the post. Join the brave and happy few, who choose a different path. Enter on the boulevard of broken dreams. Start a new thread with a photo of a modded knife or multitool with your EDC Must post a step by step pictorial of a knife or multitool modification (scale swap not included) For those who posted like a boss. Only for the 14th year Anniversary Challenge. Post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. You have one of your pictures in the 2020 calendar or in top three of the calendar poll in any month of the given year. Start a new thread and post a photo of the LM Crunch  Multitool for thirty (30) consecutive days. Start a new thread and post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Start a new thread and post a photo of a traditional folder for thirty (30) consecutive days. Start a new thread and post a photo of the leatherman (supertool, core, hacks) for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread with a photo showing the Swiss Army Knife   Toothpick being used in an unusual way. You have one of your pictures in the 2019 calendar or in top three of the calendar poll in any month of the given year. Participate in a challenge thread and post a photo of a SAK Cybertool (any variant), Swisschamp, Champion or Toolchest for thirty (30) consecutive days. Start a new thread demonstrating paracord knot tying Start a new thread with photos of your Buck knives in use Must start a thread with a photo of your camo SAK  Post a pic for Halloween of your pumpkin (or turnip or gourd or whatever you traditionally carve for Halloween!) being carved by any SAK, multitool, pocket or woods knife you may own!  Only available once a year Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread including a photo of shooting at least two (2) different airguns and at least one (1) photo of target (airguns)

nz Offline zoidberg

  • Point Of No Return
  • **********
    • Posts: 37,929
Re: Adding an Awl (Reamer) to a Wave and a Blast
Reply #2 on: August 10, 2018, 12:12:04 AM
Nicely done.   :tu:

us Offline Corso

  • Full Member
  • ***
    • Posts: 135
Re: Adding an Awl (Reamer) to a Wave and a Blast
Reply #3 on: August 10, 2018, 12:23:07 AM
Thank you!

00 Offline Dutch_Tooler

  • *
  • No Life Club
  • ******
    • Posts: 4,434
Re: Adding an Awl (Reamer) to a Wave and a Blast
Reply #4 on: August 10, 2018, 11:37:23 AM
Nice mods Corso :like:

Can I encourage you to do a summary in the Showcase sticky thread? Look up the first post for the format please. That would be awesome. Thanks :tu:
Cheers!
Dutch_Tooler

Location: Southern Germany, most of the time
Merit Badges Participate  in a Challenge thread and post a photo of a LM Pocket Survival Tool for thirty (30) consecutive days. Start a new thread with photos of your chainsaws Start a new thread and post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Start a new thread and post a photo of the leatherman (supertool, core, hacks) for thirty (30) consecutive days. Participate in a challenge thread and post a photo of a SAK Cybertool (any variant), Swisschamp, Champion or Toolchest for thirty (30) consecutive days.  Post a pic for Halloween of your pumpkin (or turnip or gourd or whatever you traditionally carve for Halloween!) being carved by any SAK, multitool, pocket or woods knife you may own!  Only available once a year Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Must start a thread showing a photo of at least three BO tools Start a new thread with photos of your zip ties in use Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Must post a step by step pictorial of a knife or MT Mod, done by you that includes changing the main chassis of the tool in a significant way. By machining, welding or cutting original design to accept new tool loads. Requests will be reviewed.  Start a new thread and post a photo of the Vic Pioneer X for thirty (30) consecutive days. Start a new thread with a photo showing the Hook in use Start a new thread with a photo of your custom ALOX with scissors Start a thread with photos of at least 1 MTO branded tool in your collection Test,please ignore Start a new thread with a photo of a modded knife or multitool with your EDC Start a new thread and post a photo of a flashlight as part of your EDC Must post a step by step pictorial of a knife or multitool modification (scale swap not included)

us Offline SteveC

  • Global Moderator
  • Just Bananas
  • *
    • Posts: 72,596
Re: Adding an Awl (Reamer) to a Wave and a Blast
Reply #5 on: August 10, 2018, 01:38:07 PM
Nicely done !  :like: :tu:
Merit Badges Start a new thread and post a photo of the Leatherman MiniTool for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread and post a photo of the 110 knife for thirty (30) consecutive days. Start a new thread with a photo of a blood blister and Mr Pinchy (Gerber Multiplier) Participate and contribute in Challenge thread and post a photo of a different blade each day for thirty (30) consecutive days. Participate  in Challenge thread and post a photo of a Buck 112 Ranger for thirty (30) consecutive days. Participate  in a Challenge thread and post a photo of a LM Pocket Survival Tool for thirty (30) consecutive days. Start a new thread and post a photo of the LM Crunch  Multitool for fifteen (15) consecutive days. Participate in a challenge by carrying  a GEC knife and post a photo of it  for thirty (30) consecutive days. Start a new thread and post a photo of the leatherman (supertool, core, hacks) for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for fifteen (15) consecutive days. Complete a 30 day challenge for carrying a different Multi tool each day of the week based on one of the daily carry threads Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread and post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Start a new thread and post a photo of a traditional folder for thirty (30) consecutive days. Start a new thread and post a photo of the discontinued sak/mt for thirty (30) consecutive days. Must start a thread showing a photo of at least eight BO tools Start a new thread and post a picture of fire making kit or fire with a multitool Start a new thread with a photo of a modded knife or multitool with your EDC Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Participate in a challenge by carrying  a Leatherman Pulse or ST200 and post a photo of it  for thirty (30) consecutive days.

us Offline Aloha

  • Global Moderator
  • *
  • Point Of No Return
  • *
    • Posts: 31,235
Re: Adding an Awl (Reamer) to a Wave and a Blast
Reply #6 on: August 10, 2018, 02:46:42 PM
Looks good.  More importantly they works better for you  :tu:
Esse Quam Videri
Merit Badges Start a new thread and post a photo of the pen for thirty (30) consecutive days. Start a new thread and post a photo of a traditional folder for thirty (30) consecutive days. Take part in the christmas pool or a rak type giveaway. Those wanting to say thank you for a rak may also nominate for the santa. Must start a thread showing a photo of at least eight BO tools Start a new thread showing photos of your outdoor cooking Must have a review written in the proper format and posted on the Main Site Start a new thread and post a picture of fire making kit or fire with a multitool Start a new thread and post a photo of a flashlight as part of your EDC Start a new thread with photos of camping, including those showing preferred camping equipment Start a new thread with photos of a Japanese made PST in your collection Start a thread with a photo of at least ten OPT's in your collection Start a thread with photos of at least 5 different Juice models in your collection

us Offline Corso

  • Full Member
  • ***
    • Posts: 135
Re: Adding an Awl (Reamer) to a Wave and a Blast
Reply #7 on: August 10, 2018, 04:08:27 PM
Quote from: Dutch_Tooler on August 10, 2018, 11:37:23 AM
Nice mods Corso :like:

Can I encourage you to do a summary in the Showcase sticky thread? Look up the first post for the format please. That would be awesome. Thanks :tu:

Done, thanks!

00 Offline Dutch_Tooler

  • *
  • No Life Club
  • ******
    • Posts: 4,434
Re: Adding an Awl (Reamer) to a Wave and a Blast
Reply #8 on: August 10, 2018, 04:30:15 PM
 :cheers: great, thanks :tu:
Cheers!
Dutch_Tooler

Location: Southern Germany, most of the time
Merit Badges Participate  in a Challenge thread and post a photo of a LM Pocket Survival Tool for thirty (30) consecutive days. Start a new thread with photos of your chainsaws Start a new thread and post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Start a new thread and post a photo of the leatherman (supertool, core, hacks) for thirty (30) consecutive days. Participate in a challenge thread and post a photo of a SAK Cybertool (any variant), Swisschamp, Champion or Toolchest for thirty (30) consecutive days.  Post a pic for Halloween of your pumpkin (or turnip or gourd or whatever you traditionally carve for Halloween!) being carved by any SAK, multitool, pocket or woods knife you may own!  Only available once a year Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Must start a thread showing a photo of at least three BO tools Start a new thread with photos of your zip ties in use Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Must post a step by step pictorial of a knife or MT Mod, done by you that includes changing the main chassis of the tool in a significant way. By machining, welding or cutting original design to accept new tool loads. Requests will be reviewed.  Start a new thread and post a photo of the Vic Pioneer X for thirty (30) consecutive days. Start a new thread with a photo showing the Hook in use Start a new thread with a photo of your custom ALOX with scissors Start a thread with photos of at least 1 MTO branded tool in your collection Test,please ignore Start a new thread with a photo of a modded knife or multitool with your EDC Start a new thread and post a photo of a flashlight as part of your EDC Must post a step by step pictorial of a knife or multitool modification (scale swap not included)

au Offline ReamerPunch

  • Thread Killer 2017
  • Global Moderator
  • *
  • Zombie Apprentice
  • *
    • Posts: 11,993
  • Born to multitask.
Re: Adding an Awl (Reamer) to a Wave and a Blast
Reply #9 on: August 10, 2018, 04:43:56 PM
Great solution to the problem!  :like:
I just removed the flathead from my Charge and put the awl in its place. I'd rather have both and lose the micro driver.
Merit Badges Participate in a Challenge thread and post a photo of a tool made in a specific country for thirty (30) consecutive days. Participate in the Challenge thread and post a photo of a Flashlight for thirty (30) consecutive days. Participate in a Challenge, carry a fire-starting item and post a picture daily  (in use if possible) for 30 days. Lighters, matches, ferro rods, fire pistons, Signal, candles, sparkers, tinder, stoves, bowdrill sets. Carry an orange item and post a picture of it everyday for 30 days.  Carry tools with single functions only. No multi-tools, no multi-layer Swiss Army Knives, no combo one-piece tools and post a photo for thirty (30) consecutive days. Participate in a Challenge thread and post a photo of a SAK-alike, aka multi-layered, knife-based pocket tools for thirty (30) consecutive days. Participate in a Challenge thread and post a photo of  a Bladeless Multitool for 30 days For each of the 30 days, or for as many as you are able to, post a picture of: Progress- Meals- Activities- Gear and participate in the thread and encourage each other. Participate and contribute in Challenge thread and post a photo of either an Axe, MT/Folding knife or Fixed blade (picked at the beginning of challenge) for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Participate in a Challenge thread and post a photo of a Roxon tool for thirty (30) consecutive days. Participate in a Challenge thread, carry at least one black edc item, and post a photo every day for 30 consecutive days. Participate in a Challenge thread, carry at least one red edc item, and post a photo every day for 30 consecutive days. Participate in a Challenge thread, carry at least one green edc item, and post a photo every day for 30 consecutive days. Participate in a Challenge thread, carry a SAK, duct tape, and paperclip, and post a photo every day for 30 consecutive days. Participate in a Challenge thread, carry a ratcheting tool, and post a photo every day for 30 consecutive days. Create and post MTO-oriented and tool-based memes in the main meme thread. ? Participate in a Challenge thread, carry a modular tool, and post a photo every day for 30 consecutive days. Find him!

us Offline Corso

  • Full Member
  • ***
    • Posts: 135
Re: Adding an Awl (Reamer) to a Wave and a Blast
Reply #10 on: August 10, 2018, 05:17:12 PM
Quote from: ReamerPunch on August 10, 2018, 04:43:56 PM
Great solution to the problem!  :like:
I just removed the flathead from my Charge and put the awl in its place. I'd rather have both and lose the micro driver.

Go for it!  It’s a fairly straight forward operation, I used a hacksaw and a dremel to shorten the flat driver (I got lucky and it fit perfect on the first go-round).

gb Offline Wspeed

  • *
  • Just Bananas
  • *************
    • Posts: 76,225
Re: Adding an Awl (Reamer) to a Wave and a Blast
Reply #11 on: August 10, 2018, 05:20:10 PM
You should be able to get the Hacker Badge Corso :pok: :tu:
fail to prepare prepare to fail
Merit Badges Must put something in order and provide link to the post. Join the brave and happy few, who choose a different path. Enter on the boulevard of broken dreams. Start a new thread with a photo of a modded knife or multitool with your EDC Must post a step by step pictorial of a knife or multitool modification (scale swap not included) For those who posted like a boss. Only for the 14th year Anniversary Challenge. Post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. You have one of your pictures in the 2020 calendar or in top three of the calendar poll in any month of the given year. Start a new thread and post a photo of the LM Crunch  Multitool for thirty (30) consecutive days. Start a new thread and post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Start a new thread and post a photo of a traditional folder for thirty (30) consecutive days. Start a new thread and post a photo of the leatherman (supertool, core, hacks) for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread with a photo showing the Swiss Army Knife   Toothpick being used in an unusual way. You have one of your pictures in the 2019 calendar or in top three of the calendar poll in any month of the given year. Participate in a challenge thread and post a photo of a SAK Cybertool (any variant), Swisschamp, Champion or Toolchest for thirty (30) consecutive days. Start a new thread demonstrating paracord knot tying Start a new thread with photos of your Buck knives in use Must start a thread with a photo of your camo SAK  Post a pic for Halloween of your pumpkin (or turnip or gourd or whatever you traditionally carve for Halloween!) being carved by any SAK, multitool, pocket or woods knife you may own!  Only available once a year Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread including a photo of shooting at least two (2) different airguns and at least one (1) photo of target (airguns)

us Offline SteveC

  • Global Moderator
  • Just Bananas
  • *
    • Posts: 72,596
Re: Adding an Awl (Reamer) to a Wave and a Blast
Reply #12 on: August 10, 2018, 08:14:36 PM
Quote from: Wspeed on August 10, 2018, 05:20:10 PM
You should be able to get the Hacker Badge Corso :pok: :tu:

And the user badge too once you,  well use it   :tu:
Merit Badges Start a new thread and post a photo of the Leatherman MiniTool for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread and post a photo of the 110 knife for thirty (30) consecutive days. Start a new thread with a photo of a blood blister and Mr Pinchy (Gerber Multiplier) Participate and contribute in Challenge thread and post a photo of a different blade each day for thirty (30) consecutive days. Participate  in Challenge thread and post a photo of a Buck 112 Ranger for thirty (30) consecutive days. Participate  in a Challenge thread and post a photo of a LM Pocket Survival Tool for thirty (30) consecutive days. Start a new thread and post a photo of the LM Crunch  Multitool for fifteen (15) consecutive days. Participate in a challenge by carrying  a GEC knife and post a photo of it  for thirty (30) consecutive days. Start a new thread and post a photo of the leatherman (supertool, core, hacks) for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for fifteen (15) consecutive days. Complete a 30 day challenge for carrying a different Multi tool each day of the week based on one of the daily carry threads Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread and post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Start a new thread and post a photo of a traditional folder for thirty (30) consecutive days. Start a new thread and post a photo of the discontinued sak/mt for thirty (30) consecutive days. Must start a thread showing a photo of at least eight BO tools Start a new thread and post a picture of fire making kit or fire with a multitool Start a new thread with a photo of a modded knife or multitool with your EDC Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Participate in a challenge by carrying  a Leatherman Pulse or ST200 and post a photo of it  for thirty (30) consecutive days.

gb Offline Wspeed

  • *
  • Just Bananas
  • *************
    • Posts: 76,225
Re: Adding an Awl (Reamer) to a Wave and a Blast
Reply #13 on: August 10, 2018, 08:18:59 PM
Here are the instructions for requesting the badges  :tu:
https://forum.multitool.org/index.php/topic,59292.0.html
fail to prepare prepare to fail
Merit Badges Must put something in order and provide link to the post. Join the brave and happy few, who choose a different path. Enter on the boulevard of broken dreams. Start a new thread with a photo of a modded knife or multitool with your EDC Must post a step by step pictorial of a knife or multitool modification (scale swap not included) For those who posted like a boss. Only for the 14th year Anniversary Challenge. Post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. You have one of your pictures in the 2020 calendar or in top three of the calendar poll in any month of the given year. Start a new thread and post a photo of the LM Crunch  Multitool for thirty (30) consecutive days. Start a new thread and post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Start a new thread and post a photo of a traditional folder for thirty (30) consecutive days. Start a new thread and post a photo of the leatherman (supertool, core, hacks) for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread with a photo showing the Swiss Army Knife   Toothpick being used in an unusual way. You have one of your pictures in the 2019 calendar or in top three of the calendar poll in any month of the given year. Participate in a challenge thread and post a photo of a SAK Cybertool (any variant), Swisschamp, Champion or Toolchest for thirty (30) consecutive days. Start a new thread demonstrating paracord knot tying Start a new thread with photos of your Buck knives in use Must start a thread with a photo of your camo SAK  Post a pic for Halloween of your pumpkin (or turnip or gourd or whatever you traditionally carve for Halloween!) being carved by any SAK, multitool, pocket or woods knife you may own!  Only available once a year Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread including a photo of shooting at least two (2) different airguns and at least one (1) photo of target (airguns)

us Offline Corso

  • Full Member
  • ***
    • Posts: 135
Re: Adding an Awl (Reamer) to a Wave and a Blast
Reply #14 on: August 10, 2018, 11:06:13 PM
Quote from: SteveC on August 10, 2018, 08:14:36 PM
Quote from: Wspeed on August 10, 2018, 05:20:10 PM
You should be able to get the Hacker Badge Corso :pok: :tu:

And the user badge too once you,  well use it   :tu:

 :tu:  My tools get used https://forum.multitool.org/index.php/topic,12238.msg705619.html#msg705619, I’m just particular about cleaning them!

us Offline Corso

  • Full Member
  • ***
    • Posts: 135
Re: Adding an Awl (Reamer) to a Wave and a Blast
Reply #15 on: August 10, 2018, 11:06:33 PM

gb Offline Wspeed

  • *
  • Just Bananas
  • *************
    • Posts: 76,225
Re: Adding an Awl (Reamer) to a Wave and a Blast
Reply #16 on: August 10, 2018, 11:31:23 PM
You are welcome  :cheers: :like: :like:
fail to prepare prepare to fail
Merit Badges Must put something in order and provide link to the post. Join the brave and happy few, who choose a different path. Enter on the boulevard of broken dreams. Start a new thread with a photo of a modded knife or multitool with your EDC Must post a step by step pictorial of a knife or multitool modification (scale swap not included) For those who posted like a boss. Only for the 14th year Anniversary Challenge. Post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. You have one of your pictures in the 2020 calendar or in top three of the calendar poll in any month of the given year. Start a new thread and post a photo of the LM Crunch  Multitool for thirty (30) consecutive days. Start a new thread and post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Start a new thread and post a photo of a traditional folder for thirty (30) consecutive days. Start a new thread and post a photo of the leatherman (supertool, core, hacks) for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread with a photo showing the Swiss Army Knife   Toothpick being used in an unusual way. You have one of your pictures in the 2019 calendar or in top three of the calendar poll in any month of the given year. Participate in a challenge thread and post a photo of a SAK Cybertool (any variant), Swisschamp, Champion or Toolchest for thirty (30) consecutive days. Start a new thread demonstrating paracord knot tying Start a new thread with photos of your Buck knives in use Must start a thread with a photo of your camo SAK  Post a pic for Halloween of your pumpkin (or turnip or gourd or whatever you traditionally carve for Halloween!) being carved by any SAK, multitool, pocket or woods knife you may own!  Only available once a year Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread including a photo of shooting at least two (2) different airguns and at least one (1) photo of target (airguns)

us Offline Obi1shinobee

  • Absolutely No Life Club
  • *******
    • Posts: 6,661
  • Master LM Squirt Ps4 And Lord of Navitools
Re: Adding an Awl (Reamer) to a Wave and a Blast
Reply #17 on: August 11, 2018, 01:00:24 PM
 :cheers: :cheers: :cheers: :cheers: :cheers: :like:
Merit Badges Start a new thread and post a photo of a traditional folder for thirty (30) consecutive days. Start a new thread and post a photo of the keychain for thirty (30) consecutive days. Start a new thread and post a photo of the pen for thirty (30) consecutive days. Start a new thread and post a photo daily of any SAK 74mm or smaller ( you can switch it up daily ) for thirty (30) consecutive days. Start a new thread and post a photo of the modified sak (scale swap not included) for thirty (30) consecutive days. Start a new thread and post a photo of the copper flashlight for thirty (30) consecutive days.  Start a new thread and post a photo of the Vic Pioneer X for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread and post a photo of the 111mm sak for thirty (30) consecutive days. Start a new thread and post a photo of the discontinued sak/mt for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread and post a photo of the leatherman (supertool, core, hacks) for thirty (30) consecutive days. Start a new thread and post a photo of the leatherman (blast, wave or charge) for thirty (30) consecutive days. Participate in a challenge thread and post a photo of a SAK Cybertool (any variant), Swisschamp, Champion or Toolchest for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days.

us Offline SteveC

  • Global Moderator
  • Just Bananas
  • *
    • Posts: 72,596
Re: Adding an Awl (Reamer) to a Wave and a Blast
Reply #18 on: August 11, 2018, 01:50:38 PM
Quote from: Corso on August 10, 2018, 11:06:13 PM
Quote from: SteveC on August 10, 2018, 08:14:36 PM
Quote from: Wspeed on August 10, 2018, 05:20:10 PM
You should be able to get the Hacker Badge Corso :pok: :tu:

And the user badge too once you,  well use it   :tu:

 :tu:  My tools get used https://forum.multitool.org/index.php/topic,12238.msg705619.html#msg705619, I’m just particular about cleaning them!

What a meant was once you use your new modded tool  :tu:
Merit Badges Start a new thread and post a photo of the Leatherman MiniTool for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread and post a photo of the 110 knife for thirty (30) consecutive days. Start a new thread with a photo of a blood blister and Mr Pinchy (Gerber Multiplier) Participate and contribute in Challenge thread and post a photo of a different blade each day for thirty (30) consecutive days. Participate  in Challenge thread and post a photo of a Buck 112 Ranger for thirty (30) consecutive days. Participate  in a Challenge thread and post a photo of a LM Pocket Survival Tool for thirty (30) consecutive days. Start a new thread and post a photo of the LM Crunch  Multitool for fifteen (15) consecutive days. Participate in a challenge by carrying  a GEC knife and post a photo of it  for thirty (30) consecutive days. Start a new thread and post a photo of the leatherman (supertool, core, hacks) for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for fifteen (15) consecutive days. Complete a 30 day challenge for carrying a different Multi tool each day of the week based on one of the daily carry threads Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread and post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Start a new thread and post a photo of a traditional folder for thirty (30) consecutive days. Start a new thread and post a photo of the discontinued sak/mt for thirty (30) consecutive days. Must start a thread showing a photo of at least eight BO tools Start a new thread and post a picture of fire making kit or fire with a multitool Start a new thread with a photo of a modded knife or multitool with your EDC Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Participate in a challenge by carrying  a Leatherman Pulse or ST200 and post a photo of it  for thirty (30) consecutive days.

us Offline Corso

  • Full Member
  • ***
    • Posts: 135
Re: Adding an Awl (Reamer) to a Wave and a Blast
Reply #19 on: August 11, 2018, 03:22:49 PM
Quote from: SteveC on August 11, 2018, 01:50:38 PM
What a meant was once you use your new modded tool  :tu:

 :cheers:

Pages: 1   Go Up
 

Donations
Operational Funds

Help us keep the Unworkable working!
Donate with PayPal!
May Goal: $300.00
Due Date: May 31
Total Receipts: $101.45
PayPal Fees: $5.93
Net Balance: $95.52
Below Goal: $204.48
Site Currency: USD
32% 
May Donations

Community Links
Multitool.org
Multitool Gallery
Multitool Encyclopedia
SAKWiki
Swiss Army Knights

Powered by EzPortal