Multitool.org Forum
 
Welcome, Guest. Please login or register.
Did you miss your activation email?

Login with username, password and session length
+-

Hello Lurker! Remove this ad and much more by logging in.


The parts exchangeability thread 5067

Absolutely No Life Club Posts: 5,518
Re: The parts exchangeability thread
« Reply #60 on: May 13, 2021, 01:10:19 PM »
The OP of that video commented it is a rebar plier head so that should probably for :tu:

Sent fra min M2002J9G via Tapatalk

Jr. Member Posts: 77
Re: The parts exchangeability thread
« Reply #61 on: May 16, 2021, 09:06:21 PM »
Howdy folks, Figured I'd add some more of my own measurements to this thread for anyone looking to mod

All Measurements are the thickness of the tool and are in millimeters measured by the pivot. These measurements are taken by a Vernier caliper so they may not be totally accurate but they are close.

Leatherman Kick/Fuse/Blast Tools:

Kick Head: 7.2
Knife: 1.8
Small flat driver: 2.6
Lanyard hole: .85
Blast file: 1.8

Note on at least the Kick washers, they are #8 washers if you need to buy some extras.

PST Tools

Head: 7.15
Can opener: 2.35
Philips At pivot: 2.45
Philips at widest point: 4.75
Small Driver: 2.35
File: 1.9
Knife: 2.4
Awl: 2.4
Medium Driver: 2.4
Large Driver: 2.4

Hope this helped someone!
Absolutely No Life Club Posts: 6,207
Re: The parts exchangeability thread
« Reply #62 on: June 07, 2021, 04:31:17 AM »
Way to many to list!! Gerber in lm, lm in gerber, sak in all the above plus some. The interchangeability is solely dependent on how hard you try :tu: and I have tired so many. 

If I remember correctly, wait, what was I saying?
Newbie Posts: 39
Re: The parts exchangeability thread
« Reply #63 on: July 03, 2021, 08:58:16 PM »
Long shot, but has anybody compared the Xiaomi Nextool to any of the leatherman tools out there? They post a picture of the tool cuts, and it looks like they might be near the wave or surge, just can't tell how close.
Nextool.jpg
* Nextool.jpg (Filesize: 35.19 KB)
Absolutely No Life Club Posts: 8,617
Re: The parts exchangeability thread
« Reply #64 on: August 19, 2021, 11:50:05 AM »
Could someone please tell me the thickness (at the pivot) of the ST300's saw? I'm going to guess it's around 2.4mm...

No Life Club Posts: 2,302
Re: The parts exchangeability thread
« Reply #65 on: August 20, 2021, 01:29:44 PM »
Could someone please tell me the thickness (at the pivot) of the ST300's saw? I'm going to guess it's around 2.4mm...

My caliper say its 1.9mm-ish
Absolutely No Life Club Posts: 8,617
Re: The parts exchangeability thread
« Reply #66 on: August 20, 2021, 01:48:33 PM »
Thanks Sam.  :cheers:
Since asking I realised that what I had in mind will not work, but the measurement might be useful for someone.

Global Moderator He Who Has The Most Nuts, Wins! Posts: 58,893
Re: The parts exchangeability thread
« Reply #67 on: August 21, 2021, 01:50:47 PM »
I don't see why it won't fit, where did you hear that ?
Absolutely No Life Club Posts: 8,617
Re: The parts exchangeability thread
« Reply #68 on: August 21, 2021, 02:20:13 PM »
I don't see why it won't fit, where did you hear that ?
Won't fit where?

No Life Club Posts: 2,302
Re: The parts exchangeability thread
« Reply #69 on: August 21, 2021, 07:40:57 PM »
Won't fit where?

Won't fit where it won't fit?
Jr. Member Posts: 56
Re: The parts exchangeability thread
« Reply #70 on: August 30, 2021, 04:56:53 AM »
I bought a few used tools recently and the bolts were stripped out. I drilled them out so I could access the tools for other builds. Does anyone have a source for replacement hardware? I would like to ultimately put these tools back together, I went to my local Ace Hardware this weekend and nothing was a direct fit. My Gerber tools appear to have a 3/16" inside diameter but they did not have anything that would work. Any help would be appreciated!
Absolutely No Life Club Posts: 5,518
Re: The parts exchangeability thread
« Reply #71 on: August 30, 2021, 07:39:22 AM »
I bought a few used tools recently and the bolts were stripped out. I drilled them out so I could access the tools for other builds. Does anyone have a source for replacement hardware? I would like to ultimately put these tools back together, I went to my local Ace Hardware this weekend and nothing was a direct fit. My Gerber tools appear to have a 3/16" inside diameter but they did not have anything that would work. Any help would be appreciated!
https://usaknifemaker.com/shop-categories/handle-hardware.html

Maybe something there will work :tu:

Sent fra min M2002J9G via Tapatalk

Jr. Member Posts: 56
Re: The parts exchangeability thread
« Reply #72 on: September 02, 2021, 04:01:48 PM »
Bingo!  I found a couple of options there...thanks.  Can't believe I didn't think of searching a site like this!  :cheers:
Absolutely No Life Club Posts: 5,518
Re: The parts exchangeability thread
« Reply #73 on: September 02, 2021, 05:48:19 PM »
Great! :tu:

Sent fra min M2002J9G via Tapatalk

Newbie Posts: 5
Re: The parts exchangeability thread
« Reply #74 on: September 17, 2021, 10:16:17 AM »
finding my way around this

is there any document or post containing some specifications about part sizes, thicknesses etc?
Newbie Posts: 15 Hey ho, lets go!
Re: The parts exchangeability thread
« Reply #75 on: September 18, 2021, 09:52:17 PM »
Hello all!

Does anybody know if the hook can be easily exchanged with the bottle opener/mini Phillips from a MiniChamp?

Thanks!

 

Donations

Operational Funds

Help us keep the Unworkable working!
Donate with PayPal!
May Goal: $300.00
Due Date: May 31
Total Receipts: $156.88
PayPal Fees: $10.05
Net Balance: $146.83
Below Goal: $153.17
Site Currency: USD
49% 
May Donations

Community Links


Powered by EzPortal
SMF 2.0.18 | SMF © 2020, Simple Machines
Page created in 0.056 seconds with 64 queries.
© 2018 Defender Web & Tool