Multitool.org Forum
+-

Hello Lurker! Remove this ad and much more by logging in.


In Stock Steel pivots 3 / 2.5 mm for Custom SAK by decustomforge

decustomforge · 25 · 4845
« previous next »
Pages: 1   Go Down

ru Offline decustomforge

  • Jr. Member
  • **
    • Posts: 99
  • PROGRESSIVE TIME & HIGH-END TOOLS
In Stock Steel pivots 3 / 2.5 mm for Custom SAK by decustomforge
on: November 12, 2019, 03:26:51 PM
Material: Heat treated stainless steel Aisi 321

Diameter: 2.5 mm
Barrel Lenght: 8.8 mm (For 2 layers model)
Thread: Metric m2
Diameter: 3 mm
Barrel Lenght: 8.8 mm (For 2 layers model)
Thread: Metric m2

Diameter: 2.5 mm
Barrel Lenght: 11.8 mm (For 3 layers model, for some 3 layers model pivots need to be cut slightly -0.8 mm)
Thread: Metric m2 (thread on both sides to a depth of 5 mm)
Diameter: 3 mm
Barrel Lenght: 11.8 mm (For 3 layers model, for some 3 layers model pivots need to be cut slightly -0.8 mm.)
Thread: Metric m2 (thread on both sides to a depth of 5 mm)

These pivot barrels are made for standard axial sizes of 3 and 2.5 mm,
so as not to drill holes in the tools you want to use, in rare exceptions, you only need to widen the hole in the liners +0.05 mm.

That's why this pivot barrels are the most precise for the custom SAK industry.

All pivot barrels have been heat treated to an optimum spring temper to insure the best wear and strength properties.

For more information contact me in PM or Email.
« Last Edit: November 14, 2019, 06:48:06 PM by SteveC »

se Offline kottskrapa

  • *
  • No Life Club
  • ******
    • Posts: 3,826
Re: In Stock Steel pivots 3 / 2.5 mm for Custom SAK by decustomforge
Reply #1 on: November 12, 2019, 04:06:54 PM
Thanks for the info

[It's not failure if you learn something from it]

Merit Badges Participate in a challenge by carrying  a Combo Edged knife or Multitool and post a photo of it  for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread and post a photo daily of any SAK 74mm or smaller ( you can switch it up daily ) for thirty (30) consecutive days. Start a new thread with a photo of custom or non standard SAK scales in your collection Only for the 14th year Anniversary Challenge. Post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Start a new thread and post a photo of the keychain for thirty (30) consecutive days. Start a new thread with a photo showing the Swiss Army Knife   Toothpick being used in an unusual way. Start a thread with a photo of a repair you made with duct tape Start a new thread and post a photo of the modified sak (scale swap not included) for thirty (30) consecutive days. Start a new thread with a photo of a modded knife or multitool with your EDC Join the brave and happy few, who choose a different path. Enter on the boulevard of broken dreams. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Must start a thread with a photo of your birth year SAK Start a new thread and post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Must start a thread with a photo of your stayglow SAK Start a new thread with photos of your chainsaws Start a new thread and post a photo of the minimal sak (2 layers or fewer) for thirty (30) consecutive days. Start a new thread and post a photo of a flashlight as part of your EDC

pt Offline FInixNOver

  • Hero Member
  • *****
    • Posts: 825
Re: In Stock Steel pivots 3 / 2.5 mm for Custom SAK by decustomforge
Reply #2 on: November 12, 2019, 04:56:32 PM
PM sent!

Sent from my Redmi Note 5

Merit Badges Start a new thread and post a photo daily of any SAK 74mm or smaller ( you can switch it up daily ) for thirty (30) consecutive days. Start a new thread and post a photo of a fixed blade for thirty (30) consecutive days. Start a new thread with a photo of a modded knife or multitool with your EDC Start a new thread with a photo of your custom ALOX with scissors Start a new thread and post a photo of a flashlight as part of your EDC

ru Offline decustomforge

  • Jr. Member
  • **
    • Posts: 99
  • PROGRESSIVE TIME & HIGH-END TOOLS
Re: In Stock Steel pivots 3 / 2.5 mm for Custom SAK by decustomforge
Reply #3 on: November 12, 2019, 05:04:31 PM
Quote from: kottskrapa on November 12, 2019, 04:06:54 PM
Thanks for the info

[It's not failure if you learn something from it]

If you have any questions, write me, thank you

us Offline zrxoa1

  • *
  • No Life Club
  • ******
    • Posts: 4,533
Re: In Stock Steel pivots 3 / 2.5 mm for Custom SAK by decustomforge
Reply #4 on: November 12, 2019, 05:48:14 PM
Hey there!!!  I bought from you. Just waiting on screws to arrive now.

Thumbs up to what seems to be a great product!!




Sent from my iPhone using Tapatalk
Merit Badges Participate  in Challenge thread and post a photo of a SAK Soldier for thirty (30) consecutive days. Start a new thread and post a photo of the 110 knife for thirty (30) consecutive days. Participate in a Challenge thread and post a photo of a Spyderco knife for thirty (30) consecutive days. Participate  in a Challenge thread and post a photo of a LM Pocket Survival Tool for thirty (30) consecutive days. Start a new thread and post a photo of the LM Crunch  Multitool for fifteen (15) consecutive days. Start a new thread and post a photo of the discontinued sak/mt for thirty (30) consecutive days. Start a new thread with photos of at least 5 different 111mm models in your collection Must start a thread with a photo of your birth year SAK Start a new thread with a photo of custom or non standard SAK scales in your collection Start a new thread with photos of camping, including those showing preferred camping equipment Start a new thread with photos of your Buck knives in use Start a new thread with photos of your Mora knives in use Start a new thread and post a photo of the 111mm sak for thirty (30) consecutive days. Must buy an item through the MTo Store Start a thread with photos of at least 1 MTO branded tool in your collection Start a new thread with a photo of your custom ALOX with scissors Start a new thread and post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Join the brave and happy few, who choose a different path. Enter on the boulevard of broken dreams. Must start a thread showing a photo of at least five BO tools Start a new thread and post a photo of the minimal sak (2 layers or fewer) for thirty (30) consecutive days.

ru Offline decustomforge

  • Jr. Member
  • **
    • Posts: 99
  • PROGRESSIVE TIME & HIGH-END TOOLS
Re: In Stock Steel pivots 3 / 2.5 mm for Custom SAK by decustomforge
Reply #5 on: November 12, 2019, 06:10:00 PM
Quote from: zrxoa1 on November 12, 2019, 05:48:14 PM
Hey there!!!  I bought from you. Just waiting on screws to arrive now.

Thumbs up to what seems to be a great product!!




Sent from my iPhone using Tapatalk

Hi! glad to see your message here, I long not has gone on this forum :)

gb Offline BePrepared

  • Sr. Member
  • ****
    • Posts: 418
Re: In Stock Steel pivots 3 / 2.5 mm for Custom SAK by decustomforge
Reply #6 on: November 12, 2019, 10:29:55 PM
I bought some a few weeks ago.  Then I picked up some M2x4mm and M2x5mm countersunk torx T6 screws in stainless steel from a UK based source, but there seemed to be plenty other sources who could supply the screws.  They fit!  :-)
« Last Edit: November 12, 2019, 10:41:19 PM by BePrepared »
Merit Badges Start a new thread with a photo of a modded knife or multitool with your EDC Start a new thread with photos of your hobo knives in use

ru Offline decustomforge

  • Jr. Member
  • **
    • Posts: 99
  • PROGRESSIVE TIME & HIGH-END TOOLS
Re: In Stock Steel pivots 3 / 2.5 mm for Custom SAK by decustomforge
Reply #7 on: November 13, 2019, 04:17:17 AM
Quote from: BePrepared on November 12, 2019, 10:29:55 PM
I bought some a few weeks ago.  Then I picked up some M2x4mm and M2x5mm countersunk torx T6 screws in stainless steel from a UK based source, but there seemed to be plenty other sources who could supply the screws.  They fit!  :-)

Yes, in fact, the screws are very easy to find. Did you manage to make your own custom mod? :)

gb Offline BePrepared

  • Sr. Member
  • ****
    • Posts: 418
Re: In Stock Steel pivots 3 / 2.5 mm for Custom SAK by decustomforge
Reply #8 on: November 13, 2019, 06:38:21 AM
I ave not made a mod based on the Pioneer range.  I'm still thinking abou tthe tool set I want. 

I'll post pics when I do :)
Merit Badges Start a new thread with a photo of a modded knife or multitool with your EDC Start a new thread with photos of your hobo knives in use

ru Offline decustomforge

  • Jr. Member
  • **
    • Posts: 99
  • PROGRESSIVE TIME & HIGH-END TOOLS
Re: In Stock Steel pivots 3 / 2.5 mm for Custom SAK by decustomforge
Reply #9 on: November 13, 2019, 07:31:10 AM
Quote from: BePrepared on November 13, 2019, 06:38:21 AM
I ave not made a mod based on the Pioneer range.  I'm still thinking abou tthe tool set I want. 

I'll post pics when I do :)

In any case it is interesting, keep in the know 👍🏻

Offline bliss58

  • Newbie
  • *
    • Posts: 9
Re: In Stock Steel pivots 3 / 2.5 mm for Custom SAK by decustomforge
Reply #10 on: November 14, 2019, 06:40:17 AM
I bought 2 of the 2.5mm pivots for my compact deluxe tinker mod, works really well, fit was perfect! Saved me the trouble of figuring out how to cut the brass rods and peen rods for the whole mod.

ru Offline decustomforge

  • Jr. Member
  • **
    • Posts: 99
  • PROGRESSIVE TIME & HIGH-END TOOLS
Re: In Stock Steel pivots 3 / 2.5 mm for Custom SAK by decustomforge
Reply #11 on: November 14, 2019, 01:39:35 PM
Quote from: bliss58 on November 14, 2019, 06:40:17 AM
I bought 2 of the 2.5mm pivots for my compact deluxe tinker mod, works really well, fit was perfect! Saved me the trouble of figuring out how to cut the brass rods and peen rods for the whole mod.

glad to hear from you this, thanks for the feedback!

us Offline SteveC

  • Global Moderator
  • Just Bananas
  • *
    • Posts: 70,807
Re: In Stock Steel pivots 3 / 2.5 mm for Custom SAK by decustomforge
Reply #12 on: November 14, 2019, 05:10:03 PM
Sorry to have to pull your advertisement text, but it is in violation of our forum policies on advertising. :salute:
As this is a privately owned and members funded forum we can't allow you to sell your goods here for free.
We have members here paying for the privilege to advertise and sell items they make and allowing you to do so for free wouldn't be fair to them.

If you would like to continue please sign up for a Fabricator account.

We have also pulled your website from your signature and title of this thread

If you have any more questions or would like to arrange other options for advertising, please  contact Grant Lamontagne, the site owner via email.
Nice to have you with us and you can enjoy the forum and take part in the discussions, but don't advertise anymore until you've made arrangements to do so with the forum owner or upgraded to a Fabricator account.

This has been your second warning about this,  you won't get a third.
Merit Badges Start a new thread and post a photo of the Leatherman MiniTool for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread and post a photo of the 110 knife for thirty (30) consecutive days. Start a new thread with a photo of a blood blister and Mr Pinchy (Gerber Multiplier) Participate and contribute in Challenge thread and post a photo of a different blade each day for thirty (30) consecutive days. Participate  in Challenge thread and post a photo of a Buck 112 Ranger for thirty (30) consecutive days. Participate  in a Challenge thread and post a photo of a LM Pocket Survival Tool for thirty (30) consecutive days. Start a new thread and post a photo of the LM Crunch  Multitool for fifteen (15) consecutive days. Participate in a challenge by carrying  a GEC knife and post a photo of it  for thirty (30) consecutive days. Start a new thread and post a photo of the leatherman (supertool, core, hacks) for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for fifteen (15) consecutive days. Complete a 30 day challenge for carrying a different Multi tool each day of the week based on one of the daily carry threads Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread and post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Start a new thread and post a photo of a traditional folder for thirty (30) consecutive days. Start a new thread and post a photo of the discontinued sak/mt for thirty (30) consecutive days. Must start a thread showing a photo of at least eight BO tools Start a new thread and post a picture of fire making kit or fire with a multitool Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Start a new thread with a photo of a modded knife or multitool with your EDC Participate in a challenge by carrying  a Leatherman Pulse or ST200 and post a photo of it  for thirty (30) consecutive days.

ru Offline decustomforge

  • Jr. Member
  • **
    • Posts: 99
  • PROGRESSIVE TIME & HIGH-END TOOLS
Re: In Stock Steel pivots 3 / 2.5 mm for Custom SAK by decustomforge
Reply #13 on: November 14, 2019, 06:44:53 PM
Quote from: SteveC on November 14, 2019, 05:10:03 PM
Sorry to have to pull your advertisement text, but it is in violation of our forum policies on advertising. :salute:
As this is a privately owned and members funded forum we can't allow you to sell your goods here for free.
We have members here paying for the privilege to advertise and sell items they make and allowing you to do so for free wouldn't be fair to them.

If you would like to continue please sign up for a Fabricator account.

We have also pulled your website from your signature and title of this thread

If you have any more questions or would like to arrange other options for advertising, please  contact Grant Lamontagne, the site owner via email.
Nice to have you with us and you can enjoy the forum and take part in the discussions, but don't advertise anymore until you've made arrangements to do so with the forum owner or upgraded to a Fabricator account.

This has been your second warning about this,  you won't get a third.

I was corrected :)

ru Offline decustomforge

  • Jr. Member
  • **
    • Posts: 99
  • PROGRESSIVE TIME & HIGH-END TOOLS
Re: In Stock Steel pivots 3 / 2.5 mm for Custom SAK by decustomforge
Reply #14 on: November 14, 2019, 06:53:56 PM
All steel pivots 2.5 / 3 mm available on the Etsy store: http://etsy.com/shop/decustomforge
8PJ8u3KqjgU.jpg
* 8PJ8u3KqjgU.jpg (Filesize: 211.4 KB)
tMNkglBDpMk.jpg
* tMNkglBDpMk.jpg (Filesize: 224.24 KB)
il_794xN.2030372112_jy8u.jpg
* il_794xN.2030372112_jy8u.jpg (Filesize: 100.87 KB)
il_794xN.2077981651_p4fo.jpg
* il_794xN.2077981651_p4fo.jpg (Filesize: 88.75 KB)
« Last Edit: November 14, 2019, 07:10:14 PM by decustomforge »

00 Offline Mechanickal

  • *
  • Zombie Apprentice
  • ********
    • Posts: 14,688
Re: In Stock Steel pivots 3 / 2.5 mm for Custom SAK by decustomforge
Reply #15 on: November 14, 2019, 08:03:10 PM
I don't think that will be any better :dwts:
Merit Badges Take part in the christmas pool or a rak type giveaway. Those wanting to say thank you for a rak may also nominate for the santa. Start a new thread and post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Start a thread with photos of at least twelve different colored ALOX models in your collection Start a new thread and post a photo of the 110 knife for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Must start a thread with a photo of your stayglow SAK Start a new thread with a photo showing the Hook in use Post your pocket dump photos then challenge two more members who must post their pocket dump photos within 24hrs for you to get the badge. Start a new thread with photos of your Buck knives in use Must put something in order and provide link to the post. Start a new thread with a photo of your custom ALOX with scissors Must buy an item through the MTo Store Start a thread with photos of at least 1 MTO branded tool in your collection Start a new thread with photos of your chainsaws Start a new thread with photos of your titanium gear with a multitool or sak Test,please ignore Must start a thread with a photo of your birth year SAK Start a thread with a photo of a repair you made with duct tape Start a new thread with a photo of custom or non standard SAK scales in your collection Must start a thread with a photo of at least five (5) of your watches

us Offline SteveC

  • Global Moderator
  • Just Bananas
  • *
    • Posts: 70,807
Re: In Stock Steel pivots 3 / 2.5 mm for Custom SAK by decustomforge
Reply #16 on: November 14, 2019, 08:19:21 PM
Quote from: Mechanickal on November 14, 2019, 08:03:10 PM
I don't think that will be any better :dwts:

decustomforge has become a fabricator subscriber so all is good  :tu:
Merit Badges Start a new thread and post a photo of the Leatherman MiniTool for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread and post a photo of the 110 knife for thirty (30) consecutive days. Start a new thread with a photo of a blood blister and Mr Pinchy (Gerber Multiplier) Participate and contribute in Challenge thread and post a photo of a different blade each day for thirty (30) consecutive days. Participate  in Challenge thread and post a photo of a Buck 112 Ranger for thirty (30) consecutive days. Participate  in a Challenge thread and post a photo of a LM Pocket Survival Tool for thirty (30) consecutive days. Start a new thread and post a photo of the LM Crunch  Multitool for fifteen (15) consecutive days. Participate in a challenge by carrying  a GEC knife and post a photo of it  for thirty (30) consecutive days. Start a new thread and post a photo of the leatherman (supertool, core, hacks) for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for fifteen (15) consecutive days. Complete a 30 day challenge for carrying a different Multi tool each day of the week based on one of the daily carry threads Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread and post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Start a new thread and post a photo of a traditional folder for thirty (30) consecutive days. Start a new thread and post a photo of the discontinued sak/mt for thirty (30) consecutive days. Must start a thread showing a photo of at least eight BO tools Start a new thread and post a picture of fire making kit or fire with a multitool Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Start a new thread with a photo of a modded knife or multitool with your EDC Participate in a challenge by carrying  a Leatherman Pulse or ST200 and post a photo of it  for thirty (30) consecutive days.

00 Offline Mechanickal

  • *
  • Zombie Apprentice
  • ********
    • Posts: 14,688
Re: In Stock Steel pivots 3 / 2.5 mm for Custom SAK by decustomforge
Reply #17 on: November 14, 2019, 08:28:32 PM
Quote from: SteveC on November 14, 2019, 08:19:21 PM
decustomforge has become a fabricator subscriber so all is good  :tu:


Awesome!
Merit Badges Take part in the christmas pool or a rak type giveaway. Those wanting to say thank you for a rak may also nominate for the santa. Start a new thread and post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Start a thread with photos of at least twelve different colored ALOX models in your collection Start a new thread and post a photo of the 110 knife for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Must start a thread with a photo of your stayglow SAK Start a new thread with a photo showing the Hook in use Post your pocket dump photos then challenge two more members who must post their pocket dump photos within 24hrs for you to get the badge. Start a new thread with photos of your Buck knives in use Must put something in order and provide link to the post. Start a new thread with a photo of your custom ALOX with scissors Must buy an item through the MTo Store Start a thread with photos of at least 1 MTO branded tool in your collection Start a new thread with photos of your chainsaws Start a new thread with photos of your titanium gear with a multitool or sak Test,please ignore Must start a thread with a photo of your birth year SAK Start a thread with a photo of a repair you made with duct tape Start a new thread with a photo of custom or non standard SAK scales in your collection Must start a thread with a photo of at least five (5) of your watches

ru Offline decustomforge

  • Jr. Member
  • **
    • Posts: 99
  • PROGRESSIVE TIME & HIGH-END TOOLS
Re: In Stock Steel pivots 3 / 2.5 mm for Custom SAK by decustomforge
Reply #18 on: September 30, 2023, 03:44:06 PM
Friends, below is the list of parts that are available for ordering. Shipping is available to all international countries, there are no restrictions.
For all questions and details you are interested in, please use private messages or e-mail: customforgedirect@gmail.com
Standard silver ALOX 93 mm scales set: front and back
Standard silver ALOX 84 mm scales set: front and back
Titanium DECF Frag Pattern 111 mm scales set: front and back
Titanium DECF Hard Frag Pattern 93 mm scales set: front and back
Titanium DECF Cross Bead (for microcord 2 mm)
Solid Brass DECF Cross Bead (for microcord 2 mm)
Solid Brass Rod Ø2.5 mm x 20 mm
Pivot steel Aisi 321 (thread: metric m2) Ø2.5 mm х 5.7 mm
Pivot steel Aisi 321 (thread: metric m2) Ø3 mm x 5.7 mm
Pivot steel Aisi 321 (thread: metric m2) Ø2.5 mm х 6.5 mm
Pivot steel Aisi 321 (thread: metric m2) Ø2.5 mm х 8.8 mm
Pivot steel Aisi 321 (thread: metric m2) Ø3 mm x 8.8 mm
Pivot steel Aisi 321 (thread: metric m2) Ø2.5 mm x 9.4 mm
Pivot steel Aisi 321 (thread: metric m2) Ø2.5 mm x 11 mm
Pivot steel Aisi 321 (thread: metric m2) Ø2.5 mm x 11.8 mm
Pivot steel Aisi 321 (thread: metric m2) Ø3 mm x 11.8 mm
Pivot steel Aisi 321 (thread: metric m2) Ø2.5 mm x 14.2 mm
Pivot steel Aisi 321 (thread: metric m2) Ø3 mm x 14.2 mm
Pivot steel Aisi 321 (thread: metric m2) Ø2.5 mm x 16 mm
Pivot steel Aisi 321 (thread: metric m2) Ø3 mm x 16 mm
Pivot steel Aisi 321 (thread: metric m2) Ø2.5 mm x 16.9 mm
Pivot steel Aisi 321 (thread: metric m2) Ø2.5 mm x 19 mm
Pivot steel Aisi 321 (thread: metric m2) Ø2.5 mm x 25 mm
Pivot steel Aisi 321 (thread: metric m2) Ø3 mm x 25 mm
Pivot steel Aisi 321 (thread: metric m2) Ø2.5 mm x 29 mm
Pivot steel Aisi 321 (thread: metric m2,5) Ø4 mm x 8.7 mm
Phosphor-Bronze microwashers 0.1 x 2.5 x 5.5 mm
Phosphor-Bronze microwashers 0.1 x 2.5 x 7 mm
Phosphor-Bronze microwashers 0.1 x 3 x 8 mm
Metric countersunk screws TX 6 M 2 x 4 mm
Metric countersunk screws TX 8 M 2,5 x 5 mm

us Offline SteveC

  • Global Moderator
  • Just Bananas
  • *
    • Posts: 70,807
Re: In Stock Steel pivots 3 / 2.5 mm for Custom SAK by decustomforge
Reply #19 on: October 02, 2023, 01:34:48 PM
Good to see you back and able to ship again !    :like: :tu:
Merit Badges Start a new thread and post a photo of the Leatherman MiniTool for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread and post a photo of the 110 knife for thirty (30) consecutive days. Start a new thread with a photo of a blood blister and Mr Pinchy (Gerber Multiplier) Participate and contribute in Challenge thread and post a photo of a different blade each day for thirty (30) consecutive days. Participate  in Challenge thread and post a photo of a Buck 112 Ranger for thirty (30) consecutive days. Participate  in a Challenge thread and post a photo of a LM Pocket Survival Tool for thirty (30) consecutive days. Start a new thread and post a photo of the LM Crunch  Multitool for fifteen (15) consecutive days. Participate in a challenge by carrying  a GEC knife and post a photo of it  for thirty (30) consecutive days. Start a new thread and post a photo of the leatherman (supertool, core, hacks) for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for fifteen (15) consecutive days. Complete a 30 day challenge for carrying a different Multi tool each day of the week based on one of the daily carry threads Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread and post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Start a new thread and post a photo of a traditional folder for thirty (30) consecutive days. Start a new thread and post a photo of the discontinued sak/mt for thirty (30) consecutive days. Must start a thread showing a photo of at least eight BO tools Start a new thread and post a picture of fire making kit or fire with a multitool Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Start a new thread with a photo of a modded knife or multitool with your EDC Participate in a challenge by carrying  a Leatherman Pulse or ST200 and post a photo of it  for thirty (30) consecutive days.

ru Offline decustomforge

  • Jr. Member
  • **
    • Posts: 99
  • PROGRESSIVE TIME & HIGH-END TOOLS
Re: In Stock Steel pivots 3 / 2.5 mm for Custom SAK by decustomforge
Reply #20 on: October 05, 2023, 11:32:21 PM
Thank you, for your trust and support!  :climber:

us Offline tattoosteve99

  • *
  • Absolutely No Life Club
  • *******
    • Posts: 6,325
Re: In Stock Steel pivots 3 / 2.5 mm for Custom SAK by decustomforge
Reply #21 on: October 09, 2023, 06:51:15 AM
Pm sent
If I remember correctly, wait, what was I saying?
Merit Badges Post your pocket dump photos then challenge two more members who must post their pocket dump photos within 24hrs for you to get the badge. Start a thread with photos of at least five different colored ALOX models in your collection Start a new thread with photos of camping, including those showing preferred camping equipment Start a new thread demonstrating paracord knot tying Start a new thread and post a photo of a flashlight as part of your EDC Start a thread with photos of at least 1 MTO branded tool in your collection Must start a thread with a photo of your EDC watch Must start a thread with a photo of your birth year SAK Must buy something on EDCSource

ru Offline decustomforge

  • Jr. Member
  • **
    • Posts: 99
  • PROGRESSIVE TIME & HIGH-END TOOLS
Re: In Stock Steel pivots 3 / 2.5 mm for Custom SAK by decustomforge
Reply #22 on: October 11, 2023, 12:06:08 PM
Bluing Titanium set Frag pattern scales 93 mm :)

* QuNv5CxcPkE.jpg (Filesize: 229.55 KB)

ru Offline decustomforge

  • Jr. Member
  • **
    • Posts: 99
  • PROGRESSIVE TIME & HIGH-END TOOLS
Re: In Stock Steel pivots 3 / 2.5 mm for Custom SAK by decustomforge
Reply #23 on: October 11, 2023, 12:09:31 PM
Pivot steel Aisi 321 (thread: metric m2) Ø3 mm x 14.2 mm
Pivot steel Aisi 321 (thread: metric m2) Ø3 mm x 16 mm
This steel Aisi 321 pivots sold out at the moment! Sorry.

ru Offline decustomforge

  • Jr. Member
  • **
    • Posts: 99
  • PROGRESSIVE TIME & HIGH-END TOOLS
Re: In Stock Steel pivots 3 / 2.5 mm for Custom SAK by decustomforge
Reply #24 on: July 25, 2024, 05:11:53 PM
Pivot steel Aisi 321 (thread: metric m2) Ø3 mm x 14.2 mm
Pivot steel Aisi 321 (thread: metric m2) Ø3 mm x 16 mm

IN STOCK NOW!
This pivots are fit for the 4-5 row Alox 93 mm series.

Pages: 1   Go Up
 

Donations
Operational Funds

Help us keep the Unworkable working!
Donate with PayPal!
May Goal: $300.00
Due Date: May 31
Total Receipts: $84.35
PayPal Fees: $5.00
Net Balance: $79.35
Below Goal: $220.65
Site Currency: USD
26% 
May Donations

Community Links
Multitool.org
Multitool Gallery
Multitool Encyclopedia
SAKWiki
Swiss Army Knights

Powered by EzPortal