PST concern

RaptorMan · **on:** February 19, 2009, 05:47:18 PM

Has anyone seen this type of condition on their PST or any other Leatherman. It appears that the center (i am not sure what to call it) has about a .5mm gap and it can be rotated with my fingers.

Below is a pic of what I am talking about.

Leatherman123 · **Reply #1 on:** February 19, 2009, 05:56:10 PM

I haven't, the pivot came loose!

Mr. Whippy · **Reply #2 on:** February 19, 2009, 06:05:53 PM

It happened to my PST. That prompted one of the returns for repair. Leatherman covered it.

RaptorMan · **Reply #3 on:** February 19, 2009, 07:59:11 PM

Thanks I will have to get it ready with the other two to go out.

DaveK · **Reply #4 on:** February 19, 2009, 10:27:15 PM

Nope I'm glad to say that all mine have been fine.

Leatherman123 · **Reply #5 on:** February 19, 2009, 10:29:02 PM

I have a few tools that need to be send back as well.. I hate sending them back because they take SO damn long to be returned! My SLV took a month!

RaptorMan · **Reply #6 on:** February 20, 2009, 03:07:18 AM

I am not sure when this one will go back I have a pST and the SuperTool to send back first

Leatherman123 · **Reply #7 on:** February 20, 2009, 03:08:54 AM

I have a Supertool to send back as well.. $:-\$

RaptorMan · **Reply #8 on:** February 20, 2009, 03:11:57 AM

The knife blade is broke on mine.

Dunc · **Reply #9 on:** February 20, 2009, 07:48:55 PM

I had that happen to my very first PST . There was loads of play in the plier jaws and if you rotated the pivot pin with your fingers it tightened up

Until you used it again

Bugged the hell out of me so I sold it and got a Gerber

Things went from bad to worse until I discovered Vic's

Dunc

Poncho65 · **Reply #10 on:** February 21, 2009, 05:54:46 AM

Well if you send it in I hope they can fix it instead of replace it

DaveK · **Reply #11 on:** February 21, 2009, 12:03:01 PM

I have a Gerber that has exactly this problem, but one half of the pivot has cit-outs in it so it can be tightened again (if I can find a tool to fit it). Looks like the PST pivot isn't intended to be tightened by us "end users" though.

Leatherman123 · **Reply #12 on:** February 25, 2009, 11:15:57 PM

RM, send it in ASAP! LM warranty is only 5 days behind ATM!

They are usually behind by two weeks!

I sent in my BO Charge XTi and Original SuperTool yesterday so they should be there tomorrow.. I will let 'yall know when I get them back!

RaptorMan · **Reply #13 on:** February 26, 2009, 02:37:03 AM

I hope to get the sideclip and maybe send that in with the supertool and PST I have. So the return is on hold for now.

Benner · **Reply #14 on:** February 26, 2009, 09:53:04 PM

Quote from: Leatherman123 on February 25, 2009, 11:15:57 PM

RM, send it in ASAP! LM warranty is only 5 days behind ATM! They are usually behind by two weeks! I sent in my BO Charge XTi and Original SuperTool yesterday so they should be there tomorrow.. I will let 'yall know when I get them back!

Dude, what do you do to your tools? That must be the 50th tool you've returned to them in the past year.

Mike, Lord of the Spammers! · **Reply #15 on:** February 26, 2009, 10:18:18 PM

No wonder they've changed there returns policy, and it's all Nikko's fault

Benner · **Reply #16 on:** February 26, 2009, 10:19:09 PM

Maybe that policy just applied to Nikko?

Mike, Lord of the Spammers! · **Reply #17 on:** February 26, 2009, 10:20:35 PM

Quote from: Benner on February 26, 2009, 10:19:09 PM

Maybe that policy just applied to Nikko?

I do hope so

Leatherman123 · **Reply #18 on:** February 26, 2009, 10:23:27 PM

Quote

Dude, what do you do to your tools? That must be the 50th tool you've returned to them in the past year. Tongue

I haven't used LM's warranty for a long time.. I used Victorinox's warranty several times with damn SwissTools.. I can't stand plier head play!

NeitherExtreme · **Reply #19 on:** February 27, 2009, 12:37:15 AM

That happened to the pivot in my beater KF4, I think it was because of some twisting I did with them. It really only affects the wire cutters. It doesn't bother me too much, it's just part of the tool. And like Dunc said, if you need it tight, you can just spin it around until it tightens up.

Leatherman123 · **Reply #20 on:** February 27, 2009, 12:47:33 AM

My tools have reached the factory, and they are entering tools from the 23rd.. I should have the tool in 2.5-3 weeks time!

Hello Lurker! Remove this ad and much more by logging in.

PST concern

Donations

Community Links