<?xml version="1.0" encoding="UTF-8"?><rss xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:content="http://purl.org/rss/1.0/modules/content/" xmlns:atom="http://www.w3.org/2005/Atom" version="2.0"><channel><title><![CDATA[Ultrasonic Cleaners]]></title><description><![CDATA[<p dir="auto">Ultrasonic Cleaners</p>
<p dir="auto">When I was in the market for a UC a number of years ago I put out a<br />
post looking for info and received a number of replies. Alan<br />
Tischler has had extensive experience in using these critters and<br />
the majority of the information comes from him. At the end of PART<br />
II of the message I will discuss what I purchased as well as SOS for<br />
the different models. SOS = source of supply.</p>
<p dir="auto">(Not for use with volatile solvents.)</p>
<p dir="auto">There are 2 completely different tools that are often referred to<br />
as "ultrasonic cleaners" (UC's). The best way to differentiate<br />
between the is to look at the price tag. If the list price is around<br />
$50 or below, this is NOT in the category that most actually would<br />
call a true UC. These are most often sold in places like jewelry<br />
stores and can get away with calling them UC's because they vibrate<br />
water, but the ultrasonic waves they produce have very little power<br />
to them. Yes, the will make the water dirty if you stick in a metal<br />
watch band that hasn't been cleaned in a few years in with the<br />
detergent. But you could get the same cleaning effect with a hand<br />
held vibrator (The shape is the user's choice) and holding it<br />
against any container with a detergent solution in it. A Real UC is<br />
very powerful unit. It sends very high-pitched and very powerful<br />
waves through the container, which is usually stainless steel. These<br />
high powered and high pitched (i.e. ultrasonic) actually cause<br />
microscopic bubbles to be formed in the solution and it's these high<br />
energy microscopic bubbles are what causes the desired cleaning<br />
effect. When a detergent is added it will be transferred with the<br />
high energy microscopic bubbles to hasten the cleaning process.<br />
There are several ways to separate the real and the impostors. First<br />
is price. For fountain pen / multitools / etc work we really only need<br />
the smallest units made and these will list from about $100 to $150.<br />
These will generally pull 40 to 50 watts of power and will produce ultrasound waves in<br />
the vicinity of 60,000 cycles per second. While you may not be able<br />
to hear 60 KHz itself, you will certainly be able to hear the effect<br />
of the microscopic bubbles in the tank. Much of the energy that the<br />
waves give off, like almost any source of energy will be lost in the<br />
form of heat. In a 40 watt unit that has a one cup capacity,<br />
starting around room temperature, the water or detergent solution in<br />
the unit will increase roughly 1 degree F per minute. THIS IS VERY<br />
IMPORTANT TO CONSTANTLY AWARE OF! The unit I got 7 years ago<br />
is made by Koh-I-Noor. This is an excellent unit for small items and<br />
if you know of another source for it, I can highly recommend it. Another unit they<br />
have made by Alvin, is one that I've seen in action at the now<br />
replaced Michael's in San Francisco. The employees there held it in<br />
high praise. According to the Reprint catalog, it lists for $148 and<br />
sells in the catalog for $99. It comes with a thermostat, a lid and<br />
an insert made for cleaning the nibs and feeds of almost any<br />
fountain pen, by holding them vertically. This is the perfect way<br />
every week or so to remove inks that are starting to concentrate in<br />
the feed and nib. A UC is certainly not a mandatory piece of<br />
equipment. Although for my money, it would rank very near the top.<br />
If money is very tight, you might not want to spend your money on<br />
one, even on an excellent unit costing only $99. I would, however,<br />
put it's usefulness way ahead of a lathe as was seriously suggested<br />
as a more useful tool in a discussion on the pen-pencils newsgroup<br />
long ago. This is a tool that I would not only recommend for anyone<br />
interested in pen work, but for virtually every repair person, or a<br />
just a very useful household tool. Like any tool must be used<br />
correctly. I has incredible usefulness in our hobby, but used<br />
incorrectly can do significant harm. The most important source of<br />
harm has to do with the heat buildup mentioned above. A timer,<br />
either one that cuts the power, or one that is on your person is<br />
very important. If starting with tap water, the time that it takes<br />
the bath temperature above about 125 degrees F should always be the<br />
absolute maximum. For most jobs, the limit should be under 100<br />
degrees F. For Pyroxylin plastics this is about the hottest that the<br />
plastic will be safe. Much hotter than this, the plastic can undergo<br />
totally unexpected changes, the most damaging is plastic shrinking.<br />
Also, hot temperatures can cause the plastic to melt and disfigure.<br />
This can all be prevented by length of time exposed or tossing some<br />
ice chips as suggested by Fultz. There are a few false claims that<br />
have given a bad name to UC's by some (who don't use them). Some<br />
have claimed that it can lift-off inlaid pen nibs as in many Sheaffer<br />
pens. After this was suggested as a problem in the heated discussion<br />
of the past on the pen-pencils newsgroup, one repair person,<br />
described putting a section of a PFM section in a powerful cleaner<br />
for a full 18 hours (I take it that this was one that have full heat<br />
control.) His comment that the only change was that it came out<br />
immaculate. I personally called Sheaffer and spoke with one of the<br />
staff in technical service as to how old PFMs, Imperials, Targas and<br />
now Lagacys are treated to get out dried ink, as this is one problem<br />
that all these inlaid nibs have in common-it's hard to get the last<br />
traces of ink out of them. I was told quite simply they use UC's. To<br />
date I know of only one general case that is likely to be harmed by<br />
an UC. On the other hand, the things that can be accomplished with a<br />
UC are nothing short of amazing. When restoring any sac-filled pen,<br />
removing the section from the pen and cleaning in a 1:1 solution of<br />
Formula 409 to water for 5-10 minutes will render the whole<br />
section/feed/nib as clean as knocking the parts out and cleaning<br />
each by hand separately. The majority of the time even a totally<br />
clogged section will be completely cleaned in 15 to 20 minutes. One<br />
of the things that I've found that only a UC can do is remove<br />
staining in a plastic pen due to dried ink.   At other times it may be useful<br />
to use a milder solution or one that will leave no trace after evaporation,<br />
like ammonia. While I wouldn't recommend filling the whole bath with<br />
clear household ammonia--this is fine if your work area is outside.<br />
On can very easily treat a piece in ammonia by placing the parts in<br />
a vial of ammonia/water solution and placing the vial directly in<br />
the bath. The uses are really only limited to your imagination.</p>
<p dir="auto">ultrasonic cleaner - PART II</p>
<p dir="auto">I learned a valuable lesson today as I went to read the post I wrote<br />
on which types of stains and discolorations can be removed with an<br />
ultrasonic cleaner versus types that can't. I found the post to be<br />
essentially unintelligible! It could easily be the worst written<br />
post I have posted yet. At least I hope so. For this I feel<br />
embarrassed and I apologize to many of you who have appreciated most<br />
of my efforts in the past and tried to follow this particular piece.<br />
I assure you that this does not represent that I have lost it<br />
altogether. I made the horrible error of trying to write something<br />
while I was in fact falling asleep at the keyboard. It was a<br />
question that I was eager to address, but I now realize that there<br />
is no question that is so important to address that it can't wait<br />
until morning. In a much more concise way, I think I can condense<br />
what I was trying to say into a single lucid paragraph. Vintage<br />
plastic pens, almost all of which are made from Pyroxylin, are<br />
relatively porous materials. In these plastics, discoloration falls<br />
into 2 categories. One type is when the stain or discoloration IS<br />
NOT chemically bound to the plastic. These, which are most commonly<br />
due to inks, can be removed in principle with the aid of an<br />
ultrasonic cleaner. The other type of discoloration is when stain IS<br />
chemically bound to the plastic. This can occur under a number of<br />
conditions including heat, light, and exposure to reactive agents<br />
such as fumes from rubber sacs and some types of inks. This type of<br />
stain or discoloration cannot be removed from the plastic<br />
essentially because the discoloration has become an integral part of<br />
the plastic itself. Unfortunately, this type of discoloration occurs<br />
frequently in many colors and patterns that are highly desirable,<br />
such as jade, pearl, onyx and lapis among others. Even pure<br />
colorless Pyroxylin becomes ambered, an irreversible reaction that<br />
is induced by exposure to light, heat and chemical reactants. ALAN</p>
<hr />
<p dir="auto">There is at least one factor alone that could explain the<br />
difference. That would be the efficiency of the wave generator. As<br />
even 40 watts for an appliance that is only used minutes at a time<br />
is almost negligible, there isn't much incentive to design and<br />
produce an efficient unit. For a company like Bronson, who<br />
essentially makes nothing but UC's up to tanks that hold many tens<br />
of gallons, there is an incentive for more efficient design. In<br />
short they may just have the engineering in place to make an<br />
efficient unit without having to invest much effort in it. Another<br />
factor would be in the difference in the frequency of the waves<br />
generated. In principle, 60 KHz would be preferable than 40 KHz and<br />
this would take more power to generate. But once again, efficiency<br />
is a big question mark. A good analogy is to compare a 60 watt light<br />
bulb to a 40 watt bulb. If we define that the watts pertain only to<br />
incandescent bulbs than the 60 watt bulb produces more light at the<br />
filament. But this begs two questions. One is how far away from the<br />
incandescent bulb you are. If you are 10 feet from the 40 watt bulb<br />
and 50 feet from the 60 watt bulb, which is going to look brighter?<br />
This speaks to how efficiently the energy generated is directed into<br />
the system. The other question is what happens when the bulbs are<br />
not constrained to be incandescent? This is what I was primarily<br />
referring to above. Obviously a 40 watt fluorescent bulb will<br />
generate far more light at the source than a 60 watt incandescent<br />
bulb. This is the kind of thing I was referring to when speaking of<br />
the efficiency of the generator used. I can't say for certain that<br />
your small Bronson unit will be better or worse than the units I<br />
found. All I can say is that I know from experience that Bronson<br />
makes quality UC's in general. It would be good to come up with some<br />
standard by which we could compare the units directly. Perhaps the<br />
time needed to remove the stain made by a particular ink on a given<br />
surface. I suspect you will be happy with the Bronson UC, unless<br />
there has been some big changes in the company since I bought my<br />
last unit from them 10 years ago. This was their smallest<br />
thermostated unit at the time. I believe it had a half-gallon tank<br />
and sold for over $500. ALAN</p>
<hr />
<p dir="auto">Before I had a Bronson ( Branson is the correct<br />
name of the UC (note ALAN refers to it as a BRONSON) )UC in every<br />
lab I worked in. They are indeed the largest manufacturers of UC's<br />
that I am aware of. In fact, when I first decided to by one for my<br />
pen work, I contacted the regional Bronson dealer. At the time, at<br />
least according to him, they didn't have one in the $100 to $200<br />
price range as the smallest model was significantly larger. I would<br />
think that if they now have one in this size and price range it<br />
would be an excellent alternative to the ones I mentioned. I would<br />
also recommend posting this information on the Zoss list, if you<br />
haven't already, and you may certainly cite my recommendation of<br />
Bronson.</p>
<hr />
<p dir="auto">Several years ago I posted a question on the net asking for sources for a<br />
good, powerful and reasonably-priced Ultrasonic Cleaner (UC). I<br />
received a few suggestions that were worth following up. The<br />
suggestion that I got from Marc Brown I believe was THE answer. He<br />
told me about a small, powerful unit made by Koh-I-Noor,<br />
specifically for cleaning Rapidograph technical pens that use<br />
pigmented ink. I ended up buying the unit from the source he<br />
suggested, the Re-Print Corp. for $112 (list is $135). This unit has<br />
a round stainless steel tank that measures approx. 3 5/8" in<br />
diameter and 2" high - very small size. I am used to laboratory<br />
units 5 - 10 times more costly. This unit, for it's size is every bit as powerful.<br />
My first test was a Parker fountain pen that seemed to be clogged<br />
with India ink. Placed in the unit, the crud started shooting out<br />
both ends immediately. The section was completely clear in minutes.<br />
A good way to check the power of a UC is to put in cold tap water.<br />
The power of the Ultrasonic waves should heat the water to warm in<br />
about 10 minutes. This unit passed this test with flying colors.<br />
Even though the unit is shallow, It is possible to clean long<br />
objects by placing them in a along with the cleaning solution in a<br />
plastic container and placing this container in the tank, which<br />
would then contain tap water only. This is actually a very efficient<br />
way to use any UC as only as much cleaning solution as needed is<br />
used. For cleaning purposes 409 to water, about one to one is about<br />
right for very stubborn jobs, while much more dilute detergent, or<br />
even no detergent at all will suffice for easier jobs. Dilute<br />
ammonia can also be used but it is ill-advised in a room that is not<br />
adequately ventilated.  ALAN</p>
<hr />
<p dir="auto">Rather than posting info on solutions used to clean pen, nibs,<br />
parts, etc. the winner for cleaning solution to use in your UC tank<br />
is a 50/50 mix of water and 409 cleaner. It should be noted that<br />
certain items should not be cleaned in a UC. I am sure there will be<br />
posts covering the specifics as the tread develops.</p>
<hr />
<p dir="auto">Based on all the info presented and reading the tech specs as well<br />
as ALAN's love for Bronson's that is what I purchased off the<br />
Internet. I later sold it and acquired a Koh-I-Nor which has a<br />
smaller capacity but is a far superior machine when it comes to<br />
cleaning small parts. Recently I sold the Koh-I-Nor and purchase a<br />
UC from Harbor Freight for $50 which is a good size for MTs.<br />
Listed below are the sources for UC's .</p>
<p dir="auto"><a href="http://www.micromark.com/ULTRASONIC-CLEANER,8024.html" rel="nofollow ugc">http://www.micromark.com/ULTRASONIC-CLEANER,8024.html</a></p>
<p dir="auto"></p><div class="card col-md-9 col-lg-6 position-relative link-preview p-0">

<div class="card-body">
<h5 class="card-title">
<a class="text-decoration-none" href="http://151.101.1.124/cpi/ctaf/Category.taf?CategoryID=774">
Fastly error: unknown domain 151.101.1.124
</a>
</h5>
<p class="card-text line-clamp-3"></p>
</div>
<a href="http://151.101.1.124/cpi/ctaf/Category.taf?CategoryID=774" class="card-footer text-body-secondary small d-flex gap-2 align-items-center lh-2">



<img src="http://151.101.1.124/favicon.ico" alt="favicon" class="not-responsive overflow-hiddden" style="max-width:21px;max-height:21px" />



<p class="d-inline-block text-truncate mb-0"> <span class="text-secondary">(www.harborfreight.com)</span></p>
</a>
</div><p></p>
<p dir="auto"><a href="http://www.bransonic.com/" rel="nofollow ugc">http://www.bransonic.com/</a></p>
<p dir="auto"><a href="http://www.cleanosonic.com/" rel="nofollow ugc">http://www.cleanosonic.com/</a></p>
<p dir="auto"><a href="http://www.sonicsonline.com/gemoro-ultrasonic-jewelry-cleaner.html" rel="nofollow ugc">http://www.sonicsonline.com/gemoro-ultrasonic-jewelry-cleaner.html</a></p>
<p dir="auto">Use "ultrasonic" in the search engine in each of the above sites to<br />
locate the cleaners. I hope this helps all that are looking for a<br />
ultrasonic cleaner</p>
<p dir="auto">UC FAQ - <a href="http://www.coleparmer.com/techinfo/techinfo.asp?htmlfile=ultrasoniccleaner_faq.htm&amp;ID=792" rel="nofollow ugc">http://www.coleparmer.com/techinfo/techinfo.asp?htmlfile=ultrasoniccleaner_faq.htm&amp;ID=792</a></p>
<p dir="auto">EODtech<br />
12/24/2002 - original review<br />
9/29/2009 - updated</p>
]]></description><link>https://forum.multitool.org/topic/14200/ultrasonic-cleaners</link><generator>RSS for Node</generator><lastBuildDate>Fri, 20 Nov 2026 13:30:14 GMT</lastBuildDate><atom:link href="https://forum.multitool.org/topic/14200.rss" rel="self" type="application/rss+xml"/><pubDate>Tue, 29 Sep 2009 09:59:26 GMT</pubDate><ttl>60</ttl><item><title><![CDATA[Reply to Ultrasonic Cleaners on Tue, 29 Sep 2009 15:52:06 GMT]]></title><description><![CDATA[<p dir="auto">Thanks for this review about UC's. I found it informative. Could you or anyone else that has had luck using these with SAK's or MT's please tell us of your cleaning success or failures?</p>
]]></description><link>https://forum.multitool.org/post/268668</link><guid isPermaLink="true">https://forum.multitool.org/post/268668</guid><dc:creator><![CDATA[stressmaster5000]]></dc:creator><pubDate>Tue, 29 Sep 2009 15:52:06 GMT</pubDate></item><item><title><![CDATA[Reply to Ultrasonic Cleaners on Tue, 29 Sep 2009 10:10:38 GMT]]></title><description><![CDATA[<p dir="auto">I have a cheaper machine with stainless bowl bought at one of the local stores, and I love it. It does everything I need it to. It does wonders cleaning MTs. I for one do not need a higher powered unit. With that said, that was a cracking good read. I learned quite a bit about them. Excellent.  <img src="/assets/uploads/smileys/salute.gif" alt=":salute:" title="salute" class="forum-smiley emoji" /></p>
]]></description><link>https://forum.multitool.org/post/268583</link><guid isPermaLink="true">https://forum.multitool.org/post/268583</guid><dc:creator><![CDATA[Chako]]></dc:creator><pubDate>Tue, 29 Sep 2009 10:10:38 GMT</pubDate></item></channel></rss>