<?xml version="1.0" encoding="UTF-8"?><rss xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:content="http://purl.org/rss/1.0/modules/content/" xmlns:atom="http://www.w3.org/2005/Atom" version="2.0"><channel><title><![CDATA[Torx head swap mod]]></title><description><![CDATA[<p dir="auto">I tried to find info on modding a pioneer with Torx head screws but no luck. I'm sure there must be a thread about how to do it somewhere. I haven't tried a mod yet so this will be my first, is it hard to do?</p>
]]></description><link>https://forum.multitool.org/topic/66139/torx-head-swap-mod</link><generator>RSS for Node</generator><lastBuildDate>Fri, 20 Nov 2026 21:07:02 GMT</lastBuildDate><atom:link href="https://forum.multitool.org/topic/66139.rss" rel="self" type="application/rss+xml"/><pubDate>Sat, 07 May 2016 01:52:03 GMT</pubDate><ttl>60</ttl><item><title><![CDATA[Reply to Torx head swap mod on Mon, 09 May 2016 15:02:47 GMT]]></title><description><![CDATA[<p dir="auto">Rather than drilling out the tools and springs to take 1/8" knife pivots, what about the option of making 3mm and 2.5mm brass pivots by drilling and tapping brass rod?  I've had a bit of a play around with making some and it went pretty well, but I haven't tried assembling a SAK with them yet.</p>
]]></description><link>https://forum.multitool.org/post/1266182</link><guid isPermaLink="true">https://forum.multitool.org/post/1266182</guid><dc:creator><![CDATA[shibafu]]></dc:creator><pubDate>Mon, 09 May 2016 15:02:47 GMT</pubDate></item><item><title><![CDATA[Reply to Torx head swap mod on Sat, 07 May 2016 16:35:32 GMT]]></title><description><![CDATA[<p dir="auto">Word of caution. If you use carbide don't use lubricant of it gets hot. It can cause it crack, unless you have a small steady feed. Run the drill press on high speed (rpm) but drill slow.</p>
]]></description><link>https://forum.multitool.org/post/1265354</link><guid isPermaLink="true">https://forum.multitool.org/post/1265354</guid><dc:creator><![CDATA[tattoosteve99]]></dc:creator><pubDate>Sat, 07 May 2016 16:35:32 GMT</pubDate></item><item><title><![CDATA[Reply to Torx head swap mod on Sat, 07 May 2016 16:30:17 GMT]]></title><description><![CDATA[<blockquote>
<p dir="auto"><a class="plugin-mentions-user plugin-mentions-a" href="/user/hiraethus" aria-label="Profile: hiraethus">@<bdi>hiraethus</bdi></a> <a href="/post/1265133">said</a>:<br />
Good info sLaughterMed. <img src="/assets/uploads/smileys/541.gif" alt=":tu:" title="Thumbs up!" class="forum-smiley emoji" /></p>
<p dir="auto">I'd add a few points:</p>
<p dir="auto">Use carbide drills if you can get them, especially if you've got access to a drill press. They make drilling the springs and tools so much easier that I feel they're totally worth the extra cost. They are brittle though, so be careful when drilling.</p>
<p dir="auto">Instead of reaming after drilling, ** you can use a tightly rolled piece of emery or wet and dry paper held in the chuck of your drill as a hone.**</p>
<p dir="auto">Buy a countersink tool for recessing the address heads into the scales - much neater than using a drill bit. You might find you only need to recess the centre screw heads. You can also use this for deburring the holes in the tools and scales.</p>
<p dir="auto">Good luck. <img src="/assets/uploads/smileys/541.gif" alt=":tu:" title="Thumbs up!" class="forum-smiley emoji" /></p>
</blockquote>
<p dir="auto">Its funny, after all these years that is still the method I use.  Just on the tool pivot holes though to make sure they are smooth as the holes in the springs dont actually rotate.</p>
]]></description><link>https://forum.multitool.org/post/1265350</link><guid isPermaLink="true">https://forum.multitool.org/post/1265350</guid><dc:creator><![CDATA[Syph007]]></dc:creator><pubDate>Sat, 07 May 2016 16:30:17 GMT</pubDate></item><item><title><![CDATA[Reply to Torx head swap mod on Sat, 07 May 2016 15:00:28 GMT]]></title><description><![CDATA[<p dir="auto">The reason I decided to go ahead with this is I do have access to a drill press so I know it will make the job easier. I thought I would be able to buy the right length pivots so that's a issue. I have a cheap recruit for my first try.<br />
Thanks guys <img src="/assets/uploads/smileys/541.gif" alt=":tu:" title="Thumbs up!" class="forum-smiley emoji" /></p>
]]></description><link>https://forum.multitool.org/post/1265306</link><guid isPermaLink="true">https://forum.multitool.org/post/1265306</guid><dc:creator><![CDATA[parman53]]></dc:creator><pubDate>Sat, 07 May 2016 15:00:28 GMT</pubDate></item><item><title><![CDATA[Reply to Torx head swap mod on Sat, 07 May 2016 13:20:09 GMT]]></title><description><![CDATA[<p dir="auto"><img src="/assets/uploads/smileys/salute.gif" alt=":salute:" title="salute" class="forum-smiley emoji" /></p>
<p dir="auto">A few other things I remembered while I was out this morning:</p>
<p dir="auto">The Dremel tile cutting bit (#562) is carbide and 1/8" diameter. It's perfect for opening out the holes in the tools.</p>
<p dir="auto">I deburr the holes in the springs and tools with a conical ceramic grinding bit in my Dremel - a diamond burr would work too.</p>
<p dir="auto">The countersink tool I use most is a hand held one, rather than one to go in a drill chuck. Works just fine.</p>
]]></description><link>https://forum.multitool.org/post/1265249</link><guid isPermaLink="true">https://forum.multitool.org/post/1265249</guid><dc:creator><![CDATA[hiraethus]]></dc:creator><pubDate>Sat, 07 May 2016 13:20:09 GMT</pubDate></item><item><title><![CDATA[Reply to Torx head swap mod on Sat, 07 May 2016 13:10:59 GMT]]></title><description><![CDATA[<blockquote>
<p dir="auto"><a class="plugin-mentions-user plugin-mentions-a" href="/user/hiraethus" aria-label="Profile: hiraethus">@<bdi>hiraethus</bdi></a> <a href="/post/1265133">said</a>:<br />
Good info sLaughterMed. <img src="/assets/uploads/smileys/541.gif" alt=":tu:" title="Thumbs up!" class="forum-smiley emoji" /></p>
<p dir="auto">I'd add a few points:</p>
<p dir="auto">Use carbide drills if you can get them, especially if you've got access to a drill press. They make drilling the springs and tools so much easier that I feel they're totally worth the extra cost. They are brittle though, so be careful when drilling.</p>
<p dir="auto">Instead of reaming after drilling,  you can use a tightly rolled piece of emery or wet and dry paper held in the chuck of your drill as a hone.</p>
<p dir="auto">Buy a countersink tool for recessing the address heads into the scales - much neater than using a drill bit. You might find you only need to recess the centre screw heads. You can also use this for deburring the holes in the tools and scales.</p>
<p dir="auto">Good luck. <img src="/assets/uploads/smileys/541.gif" alt=":tu:" title="Thumbs up!" class="forum-smiley emoji" /></p>
</blockquote>
<p dir="auto">Thanks. I had been debating posting something like this for a while, as I could find zero info on the subject of drilling hardend stainless steel anywhere. Even the machining forums were useless; they all knew the differences in drill bits, and what works as a lube or coolant, so no one said it explicitly!</p>
<p dir="auto">Good call on the emery paper, and the countersink tool, im going to use that one.</p>
]]></description><link>https://forum.multitool.org/post/1265242</link><guid isPermaLink="true">https://forum.multitool.org/post/1265242</guid><dc:creator><![CDATA[sLaughterMed]]></dc:creator><pubDate>Sat, 07 May 2016 13:10:59 GMT</pubDate></item><item><title><![CDATA[Reply to Torx head swap mod on Sat, 07 May 2016 11:02:20 GMT]]></title><description><![CDATA[<p dir="auto">Worth repeating: work slowly and measure OFTEN. You can always take away another tenth of a millimeter, but once it's gone, it's gone.</p>
]]></description><link>https://forum.multitool.org/post/1265203</link><guid isPermaLink="true">https://forum.multitool.org/post/1265203</guid><dc:creator><![CDATA[windson]]></dc:creator><pubDate>Sat, 07 May 2016 11:02:20 GMT</pubDate></item><item><title><![CDATA[Reply to Torx head swap mod on Sat, 07 May 2016 04:57:05 GMT]]></title><description><![CDATA[<p dir="auto">Good info sLaughterMed. <img src="/assets/uploads/smileys/541.gif" alt=":tu:" title="Thumbs up!" class="forum-smiley emoji" /></p>
<p dir="auto">I'd add a few points:</p>
<p dir="auto">Use carbide drills if you can get them, especially if you've got access to a drill press. They make drilling the springs and tools so much easier that I feel they're totally worth the extra cost. They are brittle though, so be careful when drilling.</p>
<p dir="auto">Instead of reaming after drilling,  you can use a tightly rolled piece of emery or wet and dry paper held in the chuck of your drill as a hone.</p>
<p dir="auto">Buy a countersink tool for recessing the address heads into the scales - much neater than using a drill bit. You might find you only need to recess the centre screw heads. You can also use this for deburring the holes in the tools and scales.</p>
<p dir="auto">Good luck. <img src="/assets/uploads/smileys/541.gif" alt=":tu:" title="Thumbs up!" class="forum-smiley emoji" /></p>
]]></description><link>https://forum.multitool.org/post/1265133</link><guid isPermaLink="true">https://forum.multitool.org/post/1265133</guid><dc:creator><![CDATA[hiraethus]]></dc:creator><pubDate>Sat, 07 May 2016 04:57:05 GMT</pubDate></item><item><title><![CDATA[Reply to Torx head swap mod on Sat, 07 May 2016 03:07:21 GMT]]></title><description><![CDATA[<p dir="auto">I'm going to start this off by saying that this is absolutely doable at home, but it is a very long and tedious process. It is not for the faint at heart, and if you have never tried this before, I strongly suggest you get a beater Spartan or similarly cheap SAK, and practice first (better to go through a couple dollars worth of SAK and drill bits on something you dont care about, than to ruin a knife you actually like). There's a reason Syph's creations are so expensive.</p>
<p dir="auto">Ideally you would have a drill press for this but it can be done with a hand drill if you are very careful, and use HSS bits.</p>
<p dir="auto">Materials:</p>
<ol>
<li>
<p dir="auto">Drill Press (A hand drill can work, but will make this a much more daunting project)</p>
</li>
<li>
<p dir="auto">1/8" Cobalt or HSS spade drill bits (HSS if using a hand drill) - get multiples in case you break any, or they get dull and you can't resharpen them. If you go HSS I can recommend these from personal experience (im cheap, but they work): <a href="http://www.amazon.com/Magnum-Super-Premium-Drill-Pack/dp/B0055WM99I?ie=UTF8&amp;keywords=CTD%20Magnum%20Super%20Premium%201%2F8%20Drill%20Bit%20(2%20Pack)&amp;qid=1462589162&amp;ref_=sr_1_2&amp;sr=8-2" rel="nofollow ugc">http://www.amazon.com/Magnum-Super-Premium-Drill-Pack/dp/B0055WM99I?ie=UTF8&amp;keywords=CTD Magnum Super Premium 1%2F8 Drill Bit (2 Pack)&amp;qid=1462589162&amp;ref_=sr_1_2&amp;sr=8-2</a></p>
</li>
<li>
<p dir="auto">lubricant (in order of preference -and decreasing cost- cutting fluid, Wd-40, cooking oil)</p>
</li>
<li>
<p dir="auto">coolant (if using cutting fluid, this is also a coolant. water works otherwise)</p>
</li>
<li>
<p dir="auto">Reamer or rotary tool with a jewler's burr</p>
</li>
<li>
<p dir="auto">1/8" knife pivots (such as these: <a href="http://www.amazon.com/Magnum-Super-Premium-Drill-Pack/dp/B0055WM99I?ie=UTF8&amp;keywords=CTD%20Magnum%20Super%20Premium%201%2F8%20Drill%20Bit%20(2%20Pack)&amp;qid=1462589162&amp;ref_=sr_1_2&amp;sr=8-2" rel="nofollow ugc">http://www.amazon.com/Magnum-Super-Premium-Drill-Pack/dp/B0055WM99I?ie=UTF8&amp;keywords=CTD Magnum Super Premium 1%2F8 Drill Bit (2 Pack)&amp;qid=1462589162&amp;ref_=sr_1_2&amp;sr=8-2</a>)</p>
</li>
<li>
<p dir="auto">metal file/metal saw</p>
</li>
<li>
<p dir="auto">Loc-tite</p>
</li>
</ol>
<p dir="auto">Directions:</p>
<ol>
<li>
<p dir="auto">Disassemble the SAK. Drill out the rivets, pop off scales. Pull out pins, now you have SAK legos.</p>
</li>
<li>
<p dir="auto">Drill out the springs and tools (save the scales for later). You will want to stop often to cool the work piece with water, to prevent work hardening (which will make drilling out the pivots near impossible). You will want to use enough pressure to see progress being made, ideally you will see a strip of metal being drilled out, but as long as you can tell progress is being made, and the work piece is cooled often, you will be fine. Lubricating the work piece throughout the process will help keep your bit sharp and cutting effectively. Ideally you would use a cutting fluid, but if you don't plan on machining regularly, WD-40 or even olive oil will work as well.</p>
</li>
<li>
<p dir="auto">now that your holes are drilled, you need to clean up and slightly enlarge the holes. Use a reamer in a drill press (easier) or a jeweler's burr in a rotary tool. Ream (or use the burr to cut) out the hole to the correct width (you may still need coolant and lubricant for this). If using a jeweler's burr, make sure to clean up the edges of the hole as well as enlarging the hole. Stop and check the sizing often.</p>
</li>
<li>
<p dir="auto">Now for the scales. using your 1/8" drill bit, drill part way into the backside of the scales. You want to create a place for the pivots to anchor themselves into the scales.</p>
</li>
<li>
<p dir="auto">Test assemble your SAK. You will more than likely need to cut the pivots down to fit in the knife.</p>
</li>
<li>
<p dir="auto">Cut and file the pivots to length. Remember, you want them to be wide enough to stay anchored in your scales, with the pivot fully nested in either scale.</p>
</li>
<li>
<p dir="auto">(optional, only if you did not drill too far into the scale in step 4) Countersink your torx screws. Using a drill bit the size of the torx screw heads, drill slightly into the presentation side of the scale, just enough for the screw to nest into it.</p>
</li>
<li>
<p dir="auto">Test assemble. If all the tools snap correctly, and nothing is too loose, you can disassemble one last time, and use Loc-tite (or other thread locker) to keep the screws from working themselves loose.</p>
</li>
</ol>
<p dir="auto">The first page of Syph007's adventures into Alox (the link BADSAK posted) gives a good visual tutorial for this process.</p>
]]></description><link>https://forum.multitool.org/post/1265114</link><guid isPermaLink="true">https://forum.multitool.org/post/1265114</guid><dc:creator><![CDATA[sLaughterMed]]></dc:creator><pubDate>Sat, 07 May 2016 03:07:21 GMT</pubDate></item><item><title><![CDATA[Reply to Torx head swap mod on Sat, 07 May 2016 03:01:12 GMT]]></title><description><![CDATA[<blockquote>
<p dir="auto"><a class="plugin-mentions-user plugin-mentions-a" href="/user/badsak" aria-label="Profile: BADSAK">@<bdi>BADSAK</bdi></a> <a href="/post/1265111">said</a>:<br />
I think you will find what you are looking for here:</p>
<p dir="auto">/topic/34772</p>
</blockquote>
<p dir="auto">That was quick, <strong>THANK YOU</strong> <img src="/assets/uploads/smileys/salute.gif" alt=":salute:" title="salute" class="forum-smiley emoji" /></p>
]]></description><link>https://forum.multitool.org/post/1265113</link><guid isPermaLink="true">https://forum.multitool.org/post/1265113</guid><dc:creator><![CDATA[parman53]]></dc:creator><pubDate>Sat, 07 May 2016 03:01:12 GMT</pubDate></item><item><title><![CDATA[Reply to Torx head swap mod on Sat, 07 May 2016 02:39:22 GMT]]></title><description><![CDATA[<p dir="auto">I think you will find what you are looking for here:</p>
<p dir="auto">/topic/34772</p>
]]></description><link>https://forum.multitool.org/post/1265111</link><guid isPermaLink="true">https://forum.multitool.org/post/1265111</guid><dc:creator><![CDATA[BADSAK]]></dc:creator><pubDate>Sat, 07 May 2016 02:39:22 GMT</pubDate></item></channel></rss>