Can someone give me the dimensions of the SURGE!!!!!

Anthony · **on:** April 25, 2008, 03:32:30 AM

I'm trading my stainless Spirit* for a Surge, but it has no sheath, so I was wondering if it would fit any of my existing sheaths...but I need to know the dimensions of the Surge while closed.

*Trading away a Spirit? No I'm not crazy; I EDC a black oxide Spirit and the stainless one has been sitting on my desk untouched...why not turn it into a SURGE!!!!!

Leatherman123 · **Reply #1 on:** April 25, 2008, 03:36:36 AM

I like the way you think.. What sheath do you have in mind? I have MANY sheaths and I may have the one your looking it.. One more thing- SURGE!!!!!!!!!

Anthony · **Reply #2 on:** April 25, 2008, 03:54:10 AM

I have a nylon sheath I got from CountyComm a while back I'm hoping will be big enough; if not I'll get an "official" Surge sheath off ebay and EDC this beast for a while once I get it

scibeer · **Reply #3 on:** April 25, 2008, 03:56:51 AM

I think I tweaked my back lifting this up, but here's the measurements

4.5" x 1.5" wide x 13/16" thick. Weighs about 14 pounds.

Anthony · **Reply #4 on:** April 25, 2008, 04:01:17 AM

Quote from: scibeer on April 25, 2008, 03:56:51 AM

I think I tweaked my back lifting this up, but here's the measurements

4.5" x 1.5" wide x 13/16" thick. Weighs about 14 pounds.

haha thanks!

Leatherman123 · **Reply #5 on:** April 25, 2008, 04:35:38 AM

If that sheath will fit your SwissTool than it should fit the SURGE!

Anthony · **Reply #6 on:** April 29, 2008, 12:43:00 AM

I got the Surge!!! today and like it so far; I might EDC it tomorrow (It fits in that CountyComm sheath)

A quick mod releated question; Do I need two Torx bits to remove the bolts, or just one?

Leatherman123 · **Reply #7 on:** April 29, 2008, 12:43:53 AM

You only need one. BTW, is your SURGE BO or SS?

Anthony · **Reply #8 on:** April 29, 2008, 02:35:06 AM

Quote from: Leatherman123 on April 29, 2008, 12:43:53 AM

You only need one. BTW, is your SURGE BO or SS?

Stainless steel, I'd like to eventually get a BO one if I really like EDCing it.

Leatherman123 · **Reply #9 on:** April 29, 2008, 02:37:21 AM

I really think you are going to like the SURGE.

hawkchucker · **Reply #10 on:** April 29, 2008, 02:39:23 AM

Corrugated
Now that you have the toy of the Multitool collectors out there, I think it is time to get the only Multi you will ever need the.

!!MINI!!

so guy its time now to man up and get the real deal. The tool for real men.

Anthony · **Reply #11 on:** April 29, 2008, 02:55:45 AM

Quote from: hawkchucker on April 29, 2008, 02:39:23 AM

Corrugated
Now that you have the toy of the Multitool collectors out there, I think it is time to get the only Multi you will ever need the.

!!MINI!!

so guy its time now to man up and get the real deal. The tool for real men.

ha, I don't think I'll ever go smaller than the Spirit; and even then I'm carrying a Crunch with it!

J-sews · **Reply #12 on:** April 29, 2008, 03:40:31 AM

Quote from: Corrugated on April 29, 2008, 12:43:00 AM

I got the Surge!!! today and like it so far; I might EDC it tomorrow (It fits in that CountyComm sheath)

A quick mod releated question; Do I need two Torx bits to remove the bolts, or just one?

Oops, sorry I missed this question earlier Corrugated; you need TWO torx bits in order to remove the pivots on the plier end, but only ONE torx bit in order to remove the pivots on the opposite end.

Why? Because on the......lets call it "short blade" end.....the pivot pins have a flat on them that prevents them from spinning. You just need to remove the male screw and out comes the pivot pin.

On the "long blade" end the pivot pin is completely round. If you try to remove the male screw the whole damn pin will just spin round and round. (unless you have two torx bits, one on each side) $:-\$

Anthony · **Reply #13 on:** April 29, 2008, 03:49:34 AM

Good to know thanks.

Does anyone know the size of the bits I need? 6 sided security Torx for the Surge...

J-sews · **Reply #14 on:** April 29, 2008, 03:52:29 AM

Mine are marked T10H.......dunno what the H means though.

Anthony · **Reply #15 on:** April 29, 2008, 04:02:42 AM

Hmm, I'll try a "standard" T-10 and see if it lines up with the star shape snugly; if so then I'll search out the security version of the T-10.

hawkchucker · **Reply #16 on:** April 29, 2008, 11:20:01 AM

We really still need to get a bulk buy going on all the security bits for the leathermans. I would love to have a Mr Potatoe head Leatherman. Plus you could get exactly what you want.