Multitool.org Forum
+-

Hello Lurker! Remove this ad and much more by logging in.


Oht precision/tolerances in the pliers

aikon2014 · 4 · 1013
« previous next »
Pages: 1   Go Down

Offline aikon2014

  • Full Member
  • ***
    • Posts: 164
Oht precision/tolerances in the pliers
on: May 16, 2017, 10:41:50 PM
So I bought an oht but I was dissapointed because the plierhead had some side to side play which basically made the wire cutters useless because they weren't close enough to eachother to cut well. Is this common with the oht or just a bad copy? I was going to use it for my flyfishing for pike, but since it can't cut soft thin wire with those cutters as they are now I just put it in the car as an emergency tool.

england Offline Kev D

  • Absolutely No Life Club
  • *******
    • Posts: 8,570
Re: Oht precision/tolerances in the pliers
Reply #1 on: May 16, 2017, 10:44:05 PM
I bought one last week and it doesn't have that problem so I'd say no it shouldn't be
Merit Badges Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread and post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Must buy an item through the MTo Store Start a new thread and post a photo of a flashlight as part of your EDC Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a thread with a photo of a repair you made with duct tape Start a thread with photos of at least 1 MTO branded tool in your collection Must start a thread with a photo of your EDC watch Post your pocket dump photos then challenge two more members who must post their pocket dump photos within 24hrs for you to get the badge. Must put something in order and provide link to the post. Participate in a Challenge thread and post a photo of a Spyderco knife for thirty (30) consecutive days. Start a new thread with photos of camping, including those showing preferred camping equipment Must start a thread with a photo of your stayglow SAK Start a new thread with a photo of your custom ALOX with scissors Start a new thread with photos of your titanium gear with a multitool or sak Start a new thread with photos of your zip ties in use Start a new thread with a photo of a modded knife or multitool with your EDC Start a new thread and post a picture of fire making kit or fire with a multitool Take part in the christmas pool or a rak type giveaway. Those wanting to say thank you for a rak may also nominate for the santa.

us Offline Poncho65

  • Global Moderator
  • *
  • Just Bananas
  • *
    • Posts: 88,459
Re: Oht precision/tolerances in the pliers
Reply #2 on: May 16, 2017, 11:06:15 PM
I agree with Kevin :think: Pretty sure it shouldn't be that way :facepalm:

Oh and welcome to :MTO: :tu:
Merit Badges Find him! Post your pocket dump photos then challenge two more members who must post their pocket dump photos within 24hrs for you to get the badge. Must update or add a page on the Multitool.org Multitool Encyclopedia Participate in a Challenge thread, carry a ratcheting tool, and post a photo every day for 30 consecutive days. Participate in a Challenge thread, carry a Leatherman Bond, and post a photo every day for 30 consecutive days. Carry an orange item and post a picture of it everyday for 30 days. Start a thread with a photo of at least ten OPT's in your collection Participate in a challenge by carrying  a Leatherman Pulse or ST200 and post a photo of it  for thirty (30) consecutive days. Start a new thread and post a photo of the Leatherman MiniTool for thirty (30) consecutive days. In this challenge,  carry one(1) Pliers-based or Non-pliers multitool that we always have prejudice against, hate or even fear and post a picture everyday for 30 days Using EDC items randomly selected with a poker hand, post a photo of your EDC or a component of the EDC that got used during the course of the day for 4 weeks (or 30 consecutive days) In the spirit of the Batman utility belt. A 30 day challenge were you have to have at least 2 things clipped to your belt (preferably more). Start a thread and post a picture of your clipped gear each day for 30 days. Participate  in a Challenge thread and post a photo of a Leatherman Skeletool for thirty (30) consecutive days. Only for the 14th year Anniversary Challenge. Post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. You have one of your pictures in the 2020 calendar or in top three of the calendar poll in any month of the given year. Participate  in a Challenge thread and post a photo of a LM Pocket Survival Tool for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread and post a photo of the LM Crunch  Multitool for fifteen (15) consecutive days. Start a new thread and post a photo of the keychain for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. You have one of your pictures in the 2017 calendar or in top three of the calendar poll in any month of the given year.

Offline aikon2014

  • Full Member
  • ***
    • Posts: 164
Re: Oht precision/tolerances in the pliers
Reply #3 on: May 17, 2017, 04:23:28 PM
Thanks for the info! I contacted the store via email, so I am waiting for a reply!

Pages: 1   Go Up
 

Donations
Operational Funds

Help us keep the Unworkable working!
Donate with PayPal!
May Goal: $300.00
Due Date: May 31
Total Receipts: $86.45
PayPal Fees: $5.07
Net Balance: $81.38
Below Goal: $218.62
Site Currency: USD
27% 
May Donations

Community Links
Multitool.org
Multitool Gallery
Multitool Encyclopedia
SAKWiki
Swiss Army Knights

Powered by EzPortal