Multitool.org Forum
+-

Hello Lurker! Remove this ad and much more by logging in.


Crunch bit attachment hole

Matty Cohen · 6 · 1088
« previous next »
Pages: 1   Go Down

Offline Matty Cohen

  • Newbie
  • *
    • Posts: 9
Crunch bit attachment hole
on: July 08, 2017, 12:35:47 AM
Any way for LEATHERMAN to put on the bit attachment hole on the crunch to other models. I have a PULSE which I cant divorce even though I have a WAVE and ES4. I would pay Leatherman to send it back and retro fit it with the hole. Not a fan of the wave attachments.
Also Crunch folks ,are you able to do fine needle nose work with the Crunch end like grab a thin wire and wrap it ?
Thanks

us Offline Poncho65

  • Global Moderator
  • *
  • Just Bananas
  • *
    • Posts: 88,456
Re: Crunch bit attachment hole
Reply #1 on: July 08, 2017, 03:35:58 AM
Welcome to :MTO: :cheers:

I don't think LM will cut the hole but you might try the mod forum and see if a modder could do this :tu:
Merit Badges Find him! Post your pocket dump photos then challenge two more members who must post their pocket dump photos within 24hrs for you to get the badge. Must update or add a page on the Multitool.org Multitool Encyclopedia Participate in a Challenge thread, carry a ratcheting tool, and post a photo every day for 30 consecutive days. Participate in a Challenge thread, carry a Leatherman Bond, and post a photo every day for 30 consecutive days. Carry an orange item and post a picture of it everyday for 30 days. Start a thread with a photo of at least ten OPT's in your collection Participate in a challenge by carrying  a Leatherman Pulse or ST200 and post a photo of it  for thirty (30) consecutive days. Start a new thread and post a photo of the Leatherman MiniTool for thirty (30) consecutive days. In this challenge,  carry one(1) Pliers-based or Non-pliers multitool that we always have prejudice against, hate or even fear and post a picture everyday for 30 days Using EDC items randomly selected with a poker hand, post a photo of your EDC or a component of the EDC that got used during the course of the day for 4 weeks (or 30 consecutive days) In the spirit of the Batman utility belt. A 30 day challenge were you have to have at least 2 things clipped to your belt (preferably more). Start a thread and post a picture of your clipped gear each day for 30 days. Participate  in a Challenge thread and post a photo of a Leatherman Skeletool for thirty (30) consecutive days. Only for the 14th year Anniversary Challenge. Post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. You have one of your pictures in the 2020 calendar or in top three of the calendar poll in any month of the given year. Participate  in a Challenge thread and post a photo of a LM Pocket Survival Tool for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread and post a photo of the LM Crunch  Multitool for fifteen (15) consecutive days. Start a new thread and post a photo of the keychain for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. You have one of your pictures in the 2017 calendar or in top three of the calendar poll in any month of the given year.

nz Offline zoidberg

  • Point Of No Return
  • **********
    • Posts: 37,929
Re: Crunch bit attachment hole
Reply #2 on: July 08, 2017, 04:23:21 AM
Welcome to the boards mate.   :cheers:   Bit driver would have to be DIY. Also fine tasks are no problem for the Crunch.

us Offline The Copilot

  • Jr. Member
  • **
    • Posts: 86
Re: Crunch bit attachment hole
Reply #3 on: July 09, 2017, 08:36:16 PM
If you fully remove the adjustment screw on the Crunch you will find a 1/2" hex hole that fits the Leatherman bit extender and bits.  Pretty handy!

us Offline The Copilot

  • Jr. Member
  • **
    • Posts: 86
Re: Crunch bit attachment hole
Reply #4 on: July 09, 2017, 11:53:41 PM
Oops....didn't read carefully enough.  The OP was asking about adding a bit hole on models other than the Crunch.  My bad!

Offline Matty Cohen

  • Newbie
  • *
    • Posts: 9
Re: Crunch bit attachment hole
Reply #5 on: July 31, 2017, 03:26:57 AM
Yes reto fit a Pulse with the bit connector blade from Wave or even better cut the same hole the Crunch has to put a bit in the screw bolt. Thanks

Pages: 1   Go Up
 

Donations
Operational Funds

Help us keep the Unworkable working!
Donate with PayPal!
April Goal: $300.00
Due Date: Apr 30
Total Receipts: $115.65
PayPal Fees: $7.03
Net Balance: $108.62
Below Goal: $191.38
Site Currency: USD
36% 
April Donations

Community Links
Multitool.org
Multitool Gallery
Multitool Encyclopedia
SAKWiki
Swiss Army Knights

Powered by EzPortal