Multitool.org Forum
+-

Hello Lurker! Remove this ad and much more by logging in.


Replacement blade for original Super Tool

floppy · 5 · 978
« previous next »
Pages: 1   Go Down

au Offline floppy

  • Newbie
  • *
    • Posts: 19
Replacement blade for original Super Tool
on: October 05, 2018, 11:10:00 AM
I’ve inherited a well used original Super Tool and I’d like to refurbish it a bit.

One issue is that the straight edge blade has snapped off. I sent it off to Leatherman who said they said they don’t have the blades anymore to suit it because it’s so old. I declined to have it swapped for a Super Tool 300 because it has sentimental value.

Where can I get a blade to suit it? Are the blades from the ST200 interchangeable?
The last option is to find a cheap second hand super tool and take it off that.

england Offline Kev D

  • Absolutely No Life Club
  • *******
    • Posts: 8,567
Re: Replacement blade for original Super Tool
Reply #1 on: October 05, 2018, 11:42:40 AM
Welcome to the forum

If you message loki-mobile on here he may have one.

You'll need 5 posts before you can send private messages though.
Merit Badges Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread and post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Must buy an item through the MTo Store Start a new thread and post a photo of a flashlight as part of your EDC Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a thread with a photo of a repair you made with duct tape Start a thread with photos of at least 1 MTO branded tool in your collection Must start a thread with a photo of your EDC watch Post your pocket dump photos then challenge two more members who must post their pocket dump photos within 24hrs for you to get the badge. Must put something in order and provide link to the post. Participate in a Challenge thread and post a photo of a Spyderco knife for thirty (30) consecutive days. Start a new thread with photos of camping, including those showing preferred camping equipment Must start a thread with a photo of your stayglow SAK Start a new thread with a photo of your custom ALOX with scissors Start a new thread with photos of your titanium gear with a multitool or sak Start a new thread with photos of your zip ties in use Start a new thread with a photo of a modded knife or multitool with your EDC Start a new thread and post a picture of fire making kit or fire with a multitool Take part in the christmas pool or a rak type giveaway. Those wanting to say thank you for a rak may also nominate for the santa.

au Offline floppy

  • Newbie
  • *
    • Posts: 19
Re: Replacement blade for original Super Tool
Reply #2 on: October 05, 2018, 12:19:08 PM
Thanks Kev D!

au Offline pietervn

  • *
  • No Life Club
  • ******
    • Posts: 1,712
Re: Replacement blade for original Super Tool
Reply #3 on: October 05, 2018, 01:54:04 PM
G'Day mate,

I had a quick look putting the blades next to one another. I am 99% sure that they will swap out.

I have swapped the serrated blades between a SuperTool and a SuperTool 200 and it was a straight forward swap.

Cheers

Pete
Merit Badges Start a new thread with a photo of custom or non standard SAK scales in your collection Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Must start a thread with a photo of your birth year SAK Start a new thread with photos of at least 5 different 111mm models in your collection Must start a thread with a photo of your stayglow SAK Must start a thread showing a photo of at least eight BO tools Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread with photos of your titanium gear with a multitool or sak Must start a thread with a photo of at least five (5) of your watches Start a new thread with a photo of a modded knife or multitool with your EDC Must post a step by step pictorial of a knife or multitool modification (scale swap not included)

au Offline floppy

  • Newbie
  • *
    • Posts: 19
Re: Replacement blade for original Super Tool
Reply #4 on: October 06, 2018, 08:44:40 AM
Thanks for that Pete.

I’ve taken it apart for a nice clean, ready for fitting a new blade.

Pages: 1   Go Up
 

Donations
Operational Funds

Help us keep the Unworkable working!
Donate with PayPal!
April Goal: $300.00
Due Date: Apr 30
Total Receipts: $122.41
PayPal Fees: $6.85
Net Balance: $115.56
Below Goal: $184.44
Site Currency: USD
39% 
April Donations

Community Links
Multitool.org
Multitool Gallery
Multitool Encyclopedia
SAKWiki
Swiss Army Knights

Powered by EzPortal