Multitool.org Forum
+-

Hello Lurker! Remove this ad and much more by logging in.


3D Printed Victorinox Bitdriver Adapters (All Models)

greenskyfall · 5 · 445
« previous next »
Pages: 1   Go Down

Offline greenskyfall

  • Newbie
  • *
    • Posts: 12
3D Printed Victorinox Bitdriver Adapters (All Models)
on: September 27, 2025, 01:46:09 PM
3D printed bitdriver adapters for the 58mm, 91mm, and 93mm Victorinox. Uses 4mm bits for the 58mm combo tool, 1/4in bits for the 91mm caplifter and combo tools, and 1/4in bits for the 93mm caplifter.

Moderator Edit: Advertising posts removed - Please see reply No. 3 in this thread
« Last Edit: September 29, 2025, 09:11:53 AM by Huntsman »

fr Offline rvlulu

  • Full Member
  • ***
    • Posts: 100
Re: 3D Printed Victorinox Bitdriver Adapters (All Models)
Reply #1 on: September 27, 2025, 02:18:33 PM
 :like:

us Offline AzteCypher

  • *
  • No Life Club
  • ******
    • Posts: 2,970
Re: 3D Printed Victorinox Bitdriver Adapters (All Models)
Reply #2 on: September 28, 2025, 06:11:26 AM
 :iagree: :like:
May the best of your past, be the worst of your future.

Merit Badges  Carry tools with single functions only. No multi-tools, no multi-layer Swiss Army Knives, no combo one-piece tools and post a photo for thirty (30) consecutive days. Start a new thread and post a photo of a fixed blade for thirty (30) consecutive days. Start a new thread with photos of at least 12 SAKs of different frame lengths and/or shapes in your collection. Eg 58mm, 74mm, 84mm regular, 84mm slim, 85mm etc Participate in a Challenge thread, carry a keychain tool with pliers, and post a photo every day for 30 consecutive days Take part in the christmas pool or a rak type giveaway. Those wanting to say thank you for a rak may also nominate for the santa. Start a new thread and post a photo of a traditional folder for thirty (30) consecutive days. Participate in a Challenge thread, carry at least one green edc item, and post a photo every day for 30 consecutive days. Participate in a Challenge thread, carry a SAK, duct tape, and paperclip, and post a photo every day for 30 consecutive days. ? Build your own version of an MRE using off-the-shelf components, post a photo of the completed MRE and store at room temperature for 6 days or more. Consume the MRE after the storage period and post pictures and descriptions of the contents. Participate in a challenge by carrying  a Combo Edged knife or Multitool and post a photo of it  for thirty (30) consecutive days. Find him! Participate in a Challenge thread, carry a Buck knife or tool, and post a photo every day for 30 consecutive days. Participate in a Challenge and post a photo of a Utility Knife for thirty (30) consecutive days. Start a new thread and post a photo daily of any SAK 74mm or smaller ( you can switch it up daily ) for thirty (30) consecutive days.  Post a pic for Halloween of your pumpkin (or turnip or gourd or whatever you traditionally carve for Halloween!) being carved by any SAK, multitool, pocket or woods knife you may own!  Only available once a year Participate  in Challenge thread and post a photo of a Delemont SAK for thirty (30) consecutive days. Complete a 30 day challenge for carrying a different Multi tool each day of the week based on one of the daily carry threads Participate in a Challenge and post a photo of a Traditional Scout Knife (No SAK's Allowed) for thirty (30) consecutive days. Start a new thread and post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Participate  in Challenge thread and post a photo of a Alox SAK for thirty (30) consecutive days.

au Offline Huntsman

  • Global Moderator
  • *
  • Absolutely No Life Club
  • *
    • Posts: 5,386
Re: 3D Printed Victorinox Bitdriver Adapters (All Models)
Reply #3 on: September 29, 2025, 09:07:58 AM
These look like great additions to a SAK EDC - Great work !   :tu:

However, apologies, I am going to have to remove your links, as they are in violation of our forum policies on advertising. :salute:

This is a privately owned, and members funded forum, so we don't allow people to advertise here for free.
We have members paying for the privilege to advertise and allowing you to do so for free wouldn't be fair to them.
If you're searching for input and thoughts on projects you'll need to upgrade your account to a Research and Development subscription you can buy here for only $10 for 30 days or $75 a year.
Then you'll be able to post links to your project in our R&D subforum.

Or if you're trying to fund your project, or advertise, check out our Crowd Funding board.
Crowd Sourcing subscription is $15 per month or $110 a year.

Be sure to read Multitool.org Think Tank Rules too.

If you have any more questions, or these adverts are not for you benefit, or you would like arrange options for advertising your tool, or you would like to discuss this, please contact Grant Lamontagne, the site owner via email or PM.

Nice to have you with us and you can enjoy the forum and take part in the discussions, but please don't advertise anymore until you've made arrangements to do so with the forum owner.

:cheers:
Merit Badges Must update or add a page on SAKWiki Start a new thread with photos of a Japanese made PST in your collection Take part in the christmas pool or a rak type giveaway. Those wanting to say thank you for a rak may also nominate for the santa. Must buy an item through the MTo Store Start a thread with photos of at least 1 MTO branded tool in your collection Start a new thread with a photo of your custom ALOX with scissors Post your pocket dump photos then challenge two more members who must post their pocket dump photos within 24hrs for you to get the badge. Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Must start a thread with a photo of your birth year SAK Must start a thread showing a photo of at least three BO tools Start a thread with photos of at least eight different colored ALOX models in your collection Start a new thread and post a photo of a flashlight as part of your EDC Start a thread with a photo of a repair you made with duct tape Must put something in order and provide link to the post. Start a new thread with a photo of custom or non standard SAK scales in your collection

Offline greenskyfall

  • Newbie
  • *
    • Posts: 12
Re: 3D Printed Victorinox Bitdriver Adapters (All Models)
Reply #4 on: September 29, 2025, 01:39:13 PM
Gotcha. Thanks for letting me know.

Pages: 1   Go Up
 

Donations
Operational Funds

Help us keep the Unworkable working!
Donate with PayPal!
January Goal: $300.00
Due Date: Jan 31
Total Receipts: $33.86
PayPal Fees: $2.12
Net Balance: $31.74
Below Goal: $268.26
Site Currency: USD
 11%
January Donations

Community Links
Multitool.org
Multitool Gallery
Multitool Encyclopedia
SAKWiki
Swiss Army Knights

Powered by EzPortal