MLCT Crony - Need your input!
-
DOH! ::)
-
We're thinking about making these changes, what do you guys think:
-Removing the magnifying glass and putting the 1/4 inch bit driver where it is
-Removing the wire guage on top and just put bumps in for aesthitics and grip
-In a spiral pattern around the 1/4" bit we'll put hte wire guages
-We're also going to put a spring loaded ball bearing into the bit driver now to keep the bit secured in while using itWhat do you guys think?]
-Dough
-
@DoughDTD said:
We're thinking about making these changes, what do you guys think:
-Removing the magnifying glass and putting the 1/4 inch bit driver where it is
-Removing the wire guage on top and just put bumps in for aesthitics and grip
-In a spiral pattern around the 1/4" bit we'll put hte wire guages
-We're also going to put a spring loaded ball bearing into the bit driver now to keep the bit secured in while using itWhat do you guys think?]
-Dough
Remove glass is a good move and putting a bb 1/4" bit driver is excellent.
Remove wire gauge off the top is another good move - I see no need for the gauge at allPerhaps drilling into the body of the tool from the rear OR making an indent where the wire gauges are now and embedding a scribe tool in the groove or hole in the rear that could be removed and used as needed to make a mark, similar to the toothpick on a SAK.
-
As a machinist I totally am in love with this project.
However, I might make my selfish needs known ... the magnifier is what I have a fetish for ... now that my four plus decades eyes are trying to read the laser etch on a #70 drill or a 4 x 40 NF tap.
However, I'm [old] wise enough to know that my selfish needs are not the mandate of the masses.
It's a shame that my EDC "eyeballs" are not enough. It's hard to make a workable lens EDC without serious cost, scratches, utility, etc.
Still ... a nice lens that can start a fire AND read the fine print might distinguish this tool from all the others.
My .02 USD or .000023 Euro equivalent.
best-
-steve
P.S. I'll buy one or two nomatter what. Nobody understands the details anymore. Or the passion. I do. My fellow mt.org brothers do. Kudos. Cheers.

-
We're thinking about making these changes, what do you guys think:
-Removing the magnifying glass and putting the 1/4 inch bit driver where it is
-Removing the wire guage on top and just put bumps in for aesthitics and grip
-In a spiral pattern around the 1/4" bit we'll put hte wire guages
-We're also going to put a spring loaded ball bearing into the bit driver now to keep the bit secured in while using itWhat do you guys think?]
-Dough
Remove glass is a good move and putting a bb 1/4" bit driver is excellent.
Remove wire gauge off the top is another good move - I see no need for the gauge at allPerhaps drilling into the body of the tool from the rear OR making an indent where the wire gauges are now and embedding a scribe tool in the groove or hole in the rear that could be removed and used as needed to make a mark, similar to the toothpick on a SAK.
+1

-
Ok guys, I wanted to bump this thread up because I need your help on some design ideas. I am going to try and heat treat the blades myself, and a 440c would be too difficult to do at home. A tool steel, however, would not be. This means were going to have a stronger tool, but the possibility of easier rusting. My question to you guys is whether or not this trade off is worth it. I want to try and do the heat treating myself to keep the costs down, and I know I can do tool steel or plain carbon steels effectively, but not the stainless. So please chime in with your input, especially if you know about the qualities of the various grades of steel. Thanks guys
-Dough
-
Tool steel or carbon steel is fine with me. You could put your own patina on it which would make it look cool and help keep the rust down.
-
Just a thought. By removing the magnifying glass would you have enough room to place the 1/4 driver and a recess for a bit. I know the bit wouldn't sit flush but a band could hold it to the tool, the recess would keep the bit from moving around. My problem with just the bit driver is...where do you keep a bit? Just a thought....though I have not thought it through.
-
-
Can tool steel be polished up to a nice shiny finish? I think for a keychain / pocket tool, the appearance needs to be aesthetically pleasing.
-
I like the idea of a tool/carbon steel.
Like Loudliam said, a cool patina would be good. -
I don't think tool steel can be polished, but I think carbon can to a certain degree, but I prefer the patina, as you can make designs in it, and it gives it a more satin look.
-
I'm unfamiliar with the term or idea of "patina" but i will look into it with more detail. it seems this can be achieved on steel by simply applying some gun bluing, which makes it look cool and prevents rusting, so that would be cool. I'd like to get some more people's input regarding the steel before I move forward though, but thanks for your input so far guys.
-Dough
-
If you've seen a old carbon steel knife, there is a layer of oxidation that forms basically making it look brown or silvery in color. This is called a patina, and can be forced or allowed to happen over time. A lot of people who buy carbon steel moras, case xx, or other popular carbon steel knives will soak them in: Sprite, vinegar, hot sauce, lemon juice, basically anything acid and it will force a layer of oxidation. They do this to not have to worry about rust forming.
-
@DoughDTD said:
Ok guys, I wanted to bump this thread up because I need your help on some design ideas. I am going to try and heat treat the blades myself, and a 440c would be too difficult to do at home. A tool steel, however, would not be. This means were going to have a stronger tool, but the possibility of easier rusting. My question to you guys is whether or not this trade off is worth it. I want to try and do the heat treating myself to keep the costs down, and I know I can do tool steel or plain carbon steels effectively, but not the stainless. So please chime in with your input, especially if you know about the qualities of the various grades of steel. Thanks guys-Dough
anyone else?
-Dough
-
Check out crucible's website, they have lots of data on various tool steels, and recommended heat treatment.
I.e. pdf on D2, give comparison of toughness and wear resistance among D2, A2, O1 and a few others: http://www.crucibleservice.com/datash/dsD2v12NEW.pdf?CFID=115604&CFTOKEN=10788854
I like D2 in tool steels, relatively stainless and very wear resistant. Not as tough as many others but I don't think it's important in such a small tool.
-
Yea ive read up alot on the various grades and heat treat methods, and I think I'm leaning in that direction. Thanks for the additional reference though, you can never read too much about something! Great data sheet.
Anyone else have any input with respect to chaning from 440c to a tool steel?
-Dough
-
Fine by me.. for what that's worth :)
Neil
-
@DoughDTD said:
Yea ive read up alot on the various grades and heat treat methods, and I think I'm leaning in that direction. Thanks for the additional reference though, you can never read too much about something! Great data sheet.Anyone else have any input with respect to chaning from 440c to a tool steel?
-Dough
Whatever you choose should have at least some rust resistance. I have a couple of transmission gears which I think is made of some sort of tool steel and they literally would rust if you looked at them wrong, one even rusted under clear coat of paint I put on.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login