Seeking Rebar modding advice.
-
I removed the blade from my
LM Crunch for the same reason
With the knife law in the UK
-
No one else have any thoughts / opinions on the matter, that they want to share?

Sent from my iPhone using Tapatalk
Don't feel bad about the blade and go with the bit extender and 3d bits.


@Wspeed said:
I removed the blade from my
LM Crunch for the same reason
With the knife law in the UK
Yeah, I can imagine the Laws in the UK are very similar to Ireland. So I'm sure you can relate...and without looking into it, I'm sure that most EU countries follow a similar pattern?
But basically here they narrow down to "any knife carried in any public place" = Possible jail time and up to a 1000 pounds (not 5000 euro as a wrote earlier), UNLESS! ...you can provide a "good reason" for carrying it at that time. E.g. if you are a carpenter carrying a utility knife.
Knife law is defined in the firearm and offensive weapons act of 1990. PART III OFFENSIVE WEAPONS PART III Offensive Weapons Possession of knives and other articles.
9.—(1) Subject to subsections (2) and (3), where a person has with him in any public place any knife or any other article which has a blade or which is sharply pointed, he shall be guilty of an offence.
(2) It shall be a defence for a person charged with an offence under subsection (1) to prove that he had good reason or lawful authority for having the article with him in a public place.
(3) Without prejudice to the generality of subsection (2), it shall be a defence for a person charged with an offence under subsection (1) to prove that he had the article with him for use at work or for a recreational purpose.
(4) Where a person, without lawful authority or reasonable excuse (the onus of proving which shall lie on him), has with him in any public place - (a) Any flick-knife, or (b) Any other article whatsoever made or adapted for use for causing injury to or incapacitating a person, He shall be guilty of an offence.
(5) Where a person has with him in any public place any article intended by him unlawfully to cause injury to, incapacitate or intimidate any person either in a particular eventuality or otherwise, he shall be guilty of an offence.
(6) In a prosecution for an offence under subsection (5), it shall not be necessary for the prosecution to allege or prove that the intent to cause injury, incapacitate or intimidate was intent to cause injury to, incapacitate or intimidate a particular person; and if, having regard to all the circumstances (including the type of the article alleged to have been intended to cause injury, incapacitate or intimidate, the time of the day or night, and the place), the court (or the jury as the case may be) thinks it reasonable to do so, it may regard possession of the article as sufficient evidence of intent in the absence of any adequate explanation by the accused.
(7) (a) A person guilty of an offence under subsection (1) shall be liable on summary conviction to a fine not exceeding £1,000 or to imprisonment for a term not exceeding twelve months or to both.
(b) A person guilty of an offence under subsection (4) or (5) shall be liable— (i) On summary conviction, to a fine not exceeding £1,000 or to imprisonment for a term not exceeding twelve months or to both, or (ii) On conviction on indictment, to a fine or to imprisonment for a term not exceeding five years or to both.
(8) In this section “public place” includes any highway and any other premises or place to which at the material time the public have or are permitted to have access, whether on payment or otherwise, and includes any club premises and any train, vessel or vehicle used for the carriage of persons for reward.
(9) In this section “flick-knife” means a knife— (a) Which has a blade which opens when hand pressure is applied to a button, spring, lever or other device in or attached to the handle, or (b) Which has a blade which is released from the handle or sheath by the force of gravity or the application of centrifugal force and when released is locked in an open position by means of a button, spring, lever or other device.
Source: http://www.irishstatutebook.ie/1990/en/act/pub/0012/sec0009.html#zza12y1990s9
So yeah, the knives had to go in one way or the other. I haven't removed the Awl, because technically its not a "knife or any other article which has a blade or which is sharply pointed".
I have never been stopped or searched by the police here knock on wood, but I don't want to risk anything either.
-
@Don Pablo said:
You guys seem rather enthusiastic about Loki’s wrenches. :D
I was until mine stripped out completely. Engineer pliers for me.
Which one stripped out, if it was an early 4 way one and the PST size loki will likely send you a replacement. I have one and I guess the PST size was slightly oversized which would cause it to slip. loki sent me a replacement.
It was the first set.
-
My adapter for Rebar, i recommend that you go for 3d adapter cause it gives more compatibility. Dont mind blade if its not really necessary for you or you carry something else what has blade.


Only Tools Matters
-
I wish Ireland was like the UK at least.... because in the UK, you can legally carry under 3” non-locking knives like SAKs without needing a reason. :D
Of course, it’s still a bad idea to take your SAK to the pub. ;) so there are limits. -
@Antti Lammi said:
My adapter for Rebar, i recommend that you go for 3d adapter cause it gives more compatibility. Dont mind blade if its not really necessary for you or you carry something else what has blade.

Only Tools Matters
Yeah, I agree.
The 3D bit adaptor is the more feasible / reasonable option
And no, I don't need it to have a knife in it. The times I need a Knife, Serrated Blade or a Saw in it, I have a Stanley utility knife that I use, when I need a knife, which does the job perfectly for me.
I work in the wine business, so all I really need a knife for is to open boxes. :)
@Don Pablo said:
I wish Ireland was like the UK at least.... because in the UK, you can legally carry under 3” non-locking knives like SAKs without needing a reason. :D
Of course, it’s still a bad idea to take your SAK to the pub. ;) so there are limits.Agree 100%
But lets be honest; it's pretty much a daily occasion in cities like Dublin and Limerick, that someone gets jumped or attacked, so I would say that there is a good reason for the law being written the way that it is here in Ireland.
-
@Don Pablo said:
I wish Ireland was like the UK at least.... because in the UK, you can legally carry under 3” non-locking knives like SAKs without needing a reason. :D
Of course, it’s still a bad idea to take your SAK to the pub. ;) so there are limits.Agree 100%
But lets be honest; it's pretty much a daily occasion in cities like Dublin and Limerick, that someone gets jumped or attacked, so I would say that there is a good reason for the law being written the way that it is here in Ireland.
I tend to think that London and etc have the same problem.

-
@Don Pablo said:
@Don Pablo said:
I wish Ireland was like the UK at least.... because in the UK, you can legally carry under 3” non-locking knives like SAKs without needing a reason. :D
Of course, it’s still a bad idea to take your SAK to the pub. ;) so there are limits.Agree 100%
But lets be honest; it's pretty much a daily occasion in cities like Dublin and Limerick, that someone gets jumped or attacked, so I would say that there is a good reason for the law being written the way that it is here in Ireland.
I tend to think that London and etc have the same problem.

True
Sent from my iPhone using Tapatalk
-
Update:
After looking at the bit driver adaptor thingy in person, I wasn't feeling it at all, for me it was first of all too expensive for just a tiny bit which I have a gut feeling I will lose too easily, and ever since I started looking at getting my Rebar, I have been wanting to make it more personal to me, i.e also why I removed the knives and saw the way I did, because I was going to remove them anyway, and it was cheaper to buy the regular rebar than the knifmeless model......
....yeah, okay...blah..blah..blah..blah..yadda...yadda..yadda....long story short; I decided to go the "loki route", and ordered the 2D large bit driver and small bit driver parts and a set of Lokis wrenches too.
Plus I already have a homemade 2D to 3D bit adaptor which I have been using with my Charge.
I'll update the thread once I receive the parts and wrenches from Loki....and then it's modding time! ...so have the popcorn ready! ;)
-
While I am waiting for my parts and wrenches to arrive from Loki.
I keep looking at Annti’s review / comparison of the ST300 and Rebar, which got me thinking a bit.
Do you guys think the Phillips driver from the ST300, will fit in a Rebar? ...or is it too long(insert “that’s what she said” joke)?
Sent from my iPhone using Tapatalk
-
It would require a lot of modding around the pivot area. ST300 tools are compatible with Surge.
What's wrong with the Rebar's own phillips? -
@Syncop8r said:
It would require a lot of modding around the pivot area. ST300 tools are compatible with Surge.
What's wrong with the Rebar's own phillips?Ah I see...
...oh nothing wrong with it, it’s actually one of the tools I use most. For the same reason, I wanted to see if it is “upgraderable”, so to speak, with a bit of extra reach.
Sent from my iPhone using Tapatalk
-
Alright laddies!
After a long wait the stuff from Loki finally arrived, and here’s what I mcgyvered together!

So I wanted to keep all the full sized screwdrivers bit still have the small and large bit driver.
And here’s why..

I already have this homemade redneck fabulous 3D bit driver that I made ages ago for my Charge TTI, so I wanted to be able to use both 2D and 3D bits.


And that is especially when Torx and Hex are becoming more and more common, especially on European cars and different electronics

And it all fits nicely into my charges sheath as well!
And most importantly; no knives means it is legal to carry in public!
Sent from my iPhone using Tapatalk
-
Even works with my small sockets...

There’s these long bits too...

And I can even go down this route as well if needs be...

I hope it this forms a better picture of what I had envisioned and what I was hoping to achieve with this “build” / mod
Sent from my iPhone using Tapatalk
-
Looks good MMR

-
Thank you sir!

Sent from my iPhone using Tapatalk
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
(partially) ;)