Yet another SOSAKer
-
You know, i don't often take group shots of my SAKs. I'm kinda afraid to count them all because then I might think that I have enough ;)
Here are a couple of my mods:

Hey....
....why does that phillips look funny?(SAK novice here) :-\
That would be the older phillis drive, square sides instead of round.
-
Yep, the phillips has flat interior sides but is rounded on the outside. Very comfortable. The one I used also has a file on the flat side visible in the photo. I don't really have any dates as to when they were produced. Unfortunately, after putting that one together I discovered that the tang is thicker than on modern knives.

It actually works fine, the back tools are just a little tight. I'll eventually take it apart and redue it properly once I decide on a chrome plating service. Files are the only non-stainless implements on SAKs.
. . . I did check here before buying the spirit. Thanks guys!
I might consider buying an updated version of the Gerber.
-
Welcome aboard mate, and cracking mods too

-
Welcome aboard. Glad to see a saw blade on those SAKs.

-
Welcome to the forum buddy. :)
-
Just for you guys, I got together some of the SAK subsets I have for photos.

The first three are Farmers, then a Pioneer Harvester, a Pioneer, a '79 SI, and a lumberjack. I have a few more alox models on the way.

A three blade +B Hunter, a +B Jungjager, a Solo, old and new Pathfinders, a Trooper, and a Mauser, with a Mil-Tec Gak on top. Hmm, I have more 108's then 111's. . . wierd :D The only other 108 I think I would buy is an actual Vic GAK in great condition.

84s! I had another traveller, but it's in the parts bin now >:D
-
Fantastic sak porn mate

You'll fit in just fine around here :)
-
Welcome to the forum. Great SAK pictures

-
@Käfer said:
Just for you guys, I got together some of the SAK subsets I have for photos.
The first three are Farmers, then a Pioneer Harvester, a Pioneer, a '79 SI, and a lumberjack. I have a few more alox models on the way.
Is that third one a scibeer hard anodize model? I wonder if there are any of those left? :)
-
It is. They're great! I haven't seen any for sale for awhile, but I think the plan was to do another run eventually.
-
Welcome to the forums mate,great selection,like your mods,but watch out for the multi tool bug,it contagious around here.
& 
-
i like the 108mm collection, i hope one day i can get one for my own

-
Good to see you over here Kafer. You'll know a few folks here already. :)
-
-
Welcome Kafer.
Nice Alox SAK collection

-
Excuse me, me Lord, but how did ye get the awl to go onto ye modified Lumberjacke? Me thought the awl was a hair too wide?
-
Good to see you over here Kafer. You'll know a few folks here already. :)
And yet he joined anyhow. Go figure.

;) :DBen X - Yes, the stock awl is too thick to fit the saw layer. I used a trick Scibeer told us about on the other forum. You a member there? Basically you mount two awls on a really flat surface and sand them down at the same time. Of course, after all that I neglected to check the width on the tang of the vintage phillips driver :(
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
::)
???