Anything to do with motorcycles, scooter, etc...
-
@TazzieRob said:
Forget the mainland, come to Tassie! No offence, Pete, I'd love to get up through the Snowies some day
Absolutely Tassie Rules!!!
Let me know when, I'll meet you in the Snowies.
Pete
-
Out for a ride today and came across what I thought was a great photo-op

-
Cool pic GJ what is that grey building

-
Interesting looking garage we have the
same here quite a few garages have gone

-
I haven't been out for a few days. Might have to do a burger run this week.....
-
@calcifur83 said:
So, As requested by @Nix. Here is a picture of my motorcycle, in all its glory.A 2004 MV Agusta Brutale 750s. Obviously, being an MV and Italian I have enjoyed nothing but worry free motoring for the last 3-4 years!!

Sadly it is now in bits as the side stand snapped during transport in a trailer
So she is all layed up getting a fixed and some upgrades.When transporting a motorcycle it should be upright on its own suspension, and tied down securely - but dont over compress the suspension with ratchet straps. The front wheel should be secured in a chock to prevent it from flopping to the side (if front ratchet straps are attached to the frame) or to prevent the wheel from sliding left or right (I’ve seen this on a wet steel trailer).
A motorcycle should never be transported on either the side or center stands, the suspension must be active to prevent stand or frame damage.
Charles.
-
@ChopperCharles said:
When transporting a motorcycle it should be upright on its own suspension, and tied down securely - but dont over compress the suspension with ratchet straps. The front wheel should be secured in a chock to prevent it from flopping to the side (if front ratchet straps are attached to the frame) or to prevent the wheel from sliding left or right (I’ve seen this on a wet steel trailer).A motorcycle should never be transported on either the side or center stands, the suspension must be active to prevent stand or frame damage.
Charles.
Good point, CC.
I always use ratchet straps to compress the suspension, but only partly. That way the bike is stable, but has a bit of bounce to absorb the shocks of the road. I once got rescued by a flatbed and just had to grit my teeth as the driver compressed the suspension to within an inch of it's life.....

-
Good points

-

Best I've seen this done in an impromptu way is to place the front wheel right into the corner of a van just behind the cab and to then secure the bike with two or better three straps to the floor anchor points along its length. No stands.
Just make sure the bike is secure both forward and aft (accel. and braking).Better still is a bespoke trailer, but still securing the bike fore and aft.
-
All good points. Lesson learned. Still on the plus side it gave a good opportunity to install some tasty CF parts!!

-
So, this is a multitool forum, and a motorcycle thread. Seems like the perfect place to put this. I just received my MotoPressor 53231 Puncture Repair multi tool. I scoured the net for a good price and couldnt' find one, so I paid $47 for it. And of course, today when I look for a link for you all I find it on sale for $29.99 here: https://www.easternperformance.com/mid-usa-motopressor-53231-puncture-repair-portable-multi-tool-motorcycle-auto.html
D'oh!!
Here's info on the tool: https://www.giantloopmoto.com/product/motopressor-puncture-repair-tool/
Here's a third party doing a video review:
- YouTube
Auf YouTube findest du die angesagtesten Videos und Tracks. Außerdem kannst du eigene Inhalte hochladen und mit Freunden oder gleich der ganzen Welt teilen.
(www.youtube.com)
And so I have it in my hands now. It's a neat compact tool, and it's sturdy enough to do a tire repair job like shown in the videos. But, it's not a high quality tool. It's not a $50 tool at ALL. It's perhaps a $30 tool. That's a livable price.
But lets look at it a bit more, shall we?
The plier tips don't meet perfectly. They're VERY easy to deflect/twist by hand, but only in one direction. The other direction doesn't twist except with great amounts of force. (The overlapping wire cutters keep the jaws from twisting in one direction)
The reamer and eyelet tool seem reasonably well made, and they have their own liner locks.
The removable knife section is an odd choice. I don't see it as being necessary to be removable, nor do I see it necessary to have a holder for a razor blade, when a knife blade would make this more useful as a tool in general. But, as I always have a folder on me, I can't say it's a bad choice -- no overlap of tools. And it does mean no blade maintenance is necessary.From the videos and from my own handling, I can say this tool will do the intended job. Having a big beefy handle makes it much, MUCH easier to use than those tiny little plastic screwdriver type reamers and eye tools.
Overall, I give this tool a B-. It will do the job, but it's too expensive for what it is.
And what is it, exactly? Where did this design come from? What is it based on?
Well, that's easy. It's based on a Blizetech/NewPow plier knife. The chassis is the same, the pliers are the same (though the tips are finished differently), and even the scales are completely swappable.
That means, for the mod-inclined, it would be possible to add tools from the Blizetech or NewPow to this tool. OR add the reamer and eyelet tool to the blizetech/newpow knife. Or any combinaton of. I could add the OHO blade with the phillips driver, keep the pliers and tire tools, and also keep the detachable razorblade holder. But to do that I'd need a longer pivot, and I'm not sure about the Blizetech, but the newpow blade doesn't hold an edge for smurf.
I'm thinking of snagging a Blizetech, which has a phillips driver instead of a square shank, and swapping in the phillips and the flat driver/bottle opener tool into this tire tool. The liners on the tire tool don't have the slots necessary to hold the backspring for the tools in the blizetech, but the liners look like they'll swap over between tools. With some careful washer placement and swapping around the liners, I can put the phillips driver and the flat driver in the plier side handle, leaving out the largely useless can opener (It's a really, really bad can opener). I can then leave the razorblade tool alone,as it would require more modification than just a liner swap to work I think.
Really, this tool needs a phillips and flat head driver. I've often had a screw in my tire and it was easier to use a screwdriver to turn it out than to grab it with pliers.
Now... this is a bit rambling now, but I do think this tool is cool. It takes up little space and contains all the tools that are absolutely necessary for a tire repair. So that's something. It's not robust or particularly good... but then, most tire tools aren't either. They're for emergency use. This packs up smaller than most tools I've bought in the past. Previously I'd only get the T-handle tools because the tiny screwdriver ones were too hard to use. The large handle on this multitool negates that, and it definitely folds up smaller than having a T-handle reamer and T-handle eyelet tool in my motorcycle bag. Plus a razor blade and pliers. It's definitely smaller, and I think it's a worthy tool to put in your emergency tire kit. But... I also wouldn't pay more than $30 for it.
Charles.




-
Looks an interesting tool. Shame on those plier tips not meeting up however.
-
Interesting idea.

I usually carry either far too few tools with me or far too many.

-
Indeed... but almost always a multitool of some sort. Might consider one, although tyre mishaps are rare around here (roads cleaned with Teutonic efficiency, mostly).
In related news, remember this bike?
It hadn't moved over the vacation so I went ahead and pulled the trigger yesterday afternoon. I should be able to pick it up coming Friday

PS: I've been told the headlamp looks positively massive in this pic. I assure all viewers that this is mainly due to the widish-angle lens on my phone camera.
-
@Dutch_Tooler said:
Indeed... but almost always a multitool of some sort. Might consider one, although tyre mishaps are rare around here (roads cleaned with Teutonic efficiency, mostly).In related news, remember this bike?
It hadn't moved over the vacation so I went ahead and pulled the trigger yesterday afternoon. I should be able to pick it up coming Friday

PS: I've been told the headlamp looks positively massive in this pic. I assure all viewers that this is mainly due to the widish-angle lens on my phone camera.
congrats -
Congratulations on your new bike D_T

-
Looking good Dutch_Tooler.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
