black oxide or not
-
Others may correct me, but I think it's more to make the tool less shiny (ie more covert). A military function. I don't think it is an anticorrosion coating per se.
-
it helps some, not a lot. It's probably more of a cosmetic thing, (for the ninjas) and
doesn't help with the visibility (if dropped on the ground) and it wears pretty easy, but that's
character and not a bad thing.don't expect super protection and to me it's not worth the extra cost but if you like it,
go for it ;) -
It has helped me fight off Ninjas numerous times.
-
The only one that I currently own made my hands black in no time.
They say to wipe and clean the BO MTs down before handling...sage advice that.
-
I think the BO is actually controlled corrosion. Someone else might be able to give more details, but I've never seena rusty BO tool...scratched and worn BO, yes...but no rust :D
-
Some evidence suggests it may actually assist in causing corrosion*. But what it does is make the surface rust very hard to see, thus keeping anyone from being the wiser. :)
*May be dependent on specific type of oxidizing, underlying steel and my own suspect memory.
-
I like the way BO looks, but it's messy as heck. I haven't had any BO multitools, but I've had a crescent wrench and a set of nail sets. Looked neat, but the black oxide coating was greasy and got all over my hands. I had to rub each down with some paper towels several times before the coating ceased to be a problem.
-
I've only had one coffee this morning, and it was weak and tasteless, so take this with a certain level of indulgence.
THE BEST DAMNED PREVENTION FOR RUST AND CORROSION IS BASIC BLOODY MAINTENANCE.
All my of my tools swim in salt, and none of them rust*, regardless of material, because I clean and oil them!
*Not actually true, the ones with rust-proof coatings and paint rust, because the rust gets underneath. Way to Go!
-
@Nomad said:
I've only had one coffee this morning, and it was weak and tasteless, so take this with a certain level of indulgence.THE BEST DAMNED PREVENTION FOR RUST AND CORROSION IS BASIC BLOODY MAINTENANCE.
All my of my tools swim in salt, and none of them rust*, regardless of material, because I clean and oil them!
*Not actually true, the ones with rust-proof coatings and paint rust, because the rust gets underneath. Way to Go!
It's time to add me to that sig line of yours.
I'm with Nomad.
-
@Nomad said:
I've only had one coffee this morning, and it was weak and tasteless, so take this with a certain level of indulgence.THE BEST DAMNED PREVENTION FOR RUST AND CORROSION IS BASIC BLOODY MAINTENANCE.
All my of my tools swim in salt, and none of them rust*, regardless of material, because I clean and oil them!
*Not actually true, the ones with rust-proof coatings and paint rust, because the rust gets underneath. Way to Go!
Speaking of that I am about due to clean and oil mine...suggestions on the BO finish what to use and what not to?
I have been using WD40 to clean and then an oil that is used on food processing equipment to lube.
-
Hi,
Black oxide is rust (ferric or ferrous oxide) dyed black. If any of you bought a new BO tool, you'll notice black stuff on your hands. That is the die. Big thing, in the mind of the military, is to prevent reflections and easy targets.
By the way, gun blueing is also dyed rust.
Cheers - Joe
-
i like BO multitools, Victorinox first, black oxide when is used , on swisstool, makes a great effect. and it's resistent too.Bye.
-
don't care what BO is for but it just look so darn good!
-
They just look cool. What more do you need to know?

:D
-
i have 1 BO MT and 1 regular finished MT. i don't care about the finish one way or the other. i got the BO b/c it was a good price for that MT regardless of finish. i did not care for the finish on the tools themselves so i took it down a notch with some 1000 grit sandpaper and i like it better. if i could get that same MT at the price i paid in plain finish i would be all over it too.
-
I am on a BO kick at the moment.
-
I found this on wikipedia about black oxide.
My guess is the Leatherman coating is the "cold black oxide" coating and hence is a copper selenium compound.
-
@Mr. Whippy said:
I found this on wikipedia about black oxide.My guess is the Leatherman coating is the "cold black oxide" coating and hence is a copper selenium compound.
I think they go back and forth. Some of my tools have a coating that appears easy to remove (similar to the description of "cold") and some is much more resistant, similar to a DLC coating. I'd bet if they use the hot method they don't do it in house, anyone have a source for hot oxidizing near Portland? :D
-
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

