Got me an MPT
-
Any more thoughts now you have had this a few days?
Hopefully mine will be here soon! :)
-
Well I've used it for a couple of days at work (were still refiting) and overall I'm quite happy with it, the pliers have been great to use, and feel impossibly light compared to my regular work Spirit :), the screwdriver are however waaay to short :(, I've been spoilt by the reach of my Vic tool's ::)
The utility blade I've not really made my mind up about :-, I've used it for scraping ancient sellotape off some shelving I've been working on, but it's a really limited blade design, with not much of a range of uses :(
It is comfortable though, certainly it must be amoungst the best of it's generation in that regard :)
-
The screwdrivers do look short. You could always invest in the bit driver for it. I think it would still fit the MPT.
Do the tools firmly snap open?
-
@Benner said:
The screwdrivers do look short. You could always invest in the bit driver for it. I think it would still fit the MPT.Do the tools firmly snap open?
I'm not really too bothered about getting a bit kit for it, as i only bought it for occational edc, where a locker would be a no - no, I'm much to wedded to my Vic stuff to let any interlopers get any serious edc time :D
No the tool's don't firmly snap out, and there's not a lot of spring pressure to hold them in place, you'll probably find it'll be very similar overall to your PST :)
-
@micky d said:
The screwdrivers do look short. You could always invest in the bit driver for it. I think it would still fit the MPT.
Do the tools firmly snap open?
I'm not really too bothered about getting a bit kit for it, as i only bought it for occational edc, where a locker would be a no - no, I'm much to wedded to my Vic stuff to let any interlopers get any serious edc time :D
No the tool's don't firmly snap out, and there's not a lot of spring pressure to hold them in place, you'll probably find it'll be very similar overall to your PST :)
I thought you would say that. :( The tools on my multiplier sort of flop open and then flop closed. There seems to be very little snap to the hold.
I am hoping to edc mine most of the time. Because of my job, a locker is a big no no so the MPT looks perfect for EDC. Twinned with a SAK of course! :D
-
Well while the snap isn't anywhere as good as a SAK it's not terrible, maybe I'm a bit more lenient toward it, because of the number of slippies I've had?
-
@micky d said:
Well while the snap isn't anywhere as good as a SAK it's not terrible, maybe I'm a bit more lenient toward it, because of the number of slippies I've had?
If it's as good as the PST I'll be happy. :) I just hope it has more than my Multiplier which is a bit pathetic really.
Given that there of the same era...I doubt it, but at least the tool's can't close on your fingers :)
-
The file is among the thickest I've seen on a multi so I'm not sure how well the saw would work, but it is nice having it there.

Also, it looks like your model is lacking the "speedbumps" seen here. Is the opening/closing cycle smooth like a typical butterfly tool?


Which one is the newer production?
My BO and stainless ones look exactly like Spoonrobot's. Simonds file blade, speedbumps on the handles, also nail nick cutouts. My opinion is also that Mike's is an earlier model.
Mike, no doubt this earlier model is far inferior. It will probably fail on you at the worst possible moment. Best bet would be to send it on to me for safe keeping lad.
:D -
Good idea, you'd best PM me your address :D
-
Bob is one generous guy that's for sure! :)
-
Bob is generous to a fault, i'd be stupid not to take him up on his kind offer :D
-
@micky d said:
Bob is generous to a fault, i'd be stupid not to take him up on his kind offer :DAlways thinking of others instead of myself, its a burden I live with every day :D
-
Well it is here! :) I will take a few pictures and share a few thoughts later.
-
Come on where are them pics :D Here's Benner with another super duper BO tool. You'll have more BO tools than most of us put together soon :D
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
