Which sharpenter system? lanky or Smith's
-
My only experience with Lansky is their Turnbox, and it's fantastic. I use it along with my Spyderco Sharpmaker for really good PE blades.
The only smiths experience I have is the pocket diamond stone and the dual sided diamond stone. It works ok for rough stuff and reprofiling, but I use crocksticks for fine sharpening.
-
I had a Lansky , and it's great Grandpa , the loray - gave up on them , too fiddly . Went Spyderco Sharpmaker . Smith's stuff is lower end , if you want good diamond stuff ( stuff that wont shed their grit rapidly ) , go DMT .
Another option few think of , get an inexpensive , but good quality paring knife ie: Victorinox and leard freehand sharpening .
Chris
-
Between those two, Lansky for sure. Lansky is the original, the Smith's is the budget copy.
However...
I have the Lansky with diamond hones, (which last longer and retain their flatness better) and I prefer the Spyderco Sharpmaker to that. The theory of the Lansky is perfect: there is a jig to maintain the angles. In practice, it is less than perfect, as it doesn't clamp well to blades with a full flat grind. (ex. most multi-tool blades) It works better on bigger knives with a saber grind.
-
Also:
http://www.exduct.com/Special-Limited-Products/SP931D-Precision-Sharpener.htmlsame idea, cheap, should be decent coming from Exduct, diamond stones, I do not know if anybody tried it.
-
@dks said:
Also:
http://www.exduct.com/Special-Limited-Products/SP931D-Precision-Sharpener.htmlsame idea, cheap, should be decent coming from Exduct, diamond stones, I do not know if anybody tried it.
The hones themselves are awesome. Not sure of the exact grit but they made quick work of reprofiling blades however it's downfall is the rail system, made of plastic and would flex too much under use.
The Rods are attached directly via a thread on the back of the hones so they tend to get loose and they don't sit straight. Good for the price but not good in the long run.
-
Also:
http://www.exduct.com/Special-Limited-Products/SP931D-Precision-Sharpener.htmlsame idea, cheap, should be decent coming from Exduct, diamond stones, I do not know if anybody tried it.
The hones themselves are awesome. Not sure of the exact grit but they made quick work of reprofiling blades however it's downfall is the rail system, made of plastic and would flex too much under use.
The Rods are attached directly via a thread on the back of the hones so they tend to get loose and they don't sit straight. Good for the price but not good in the long run.
From the last q&a on that page:
**
360grit,480grit, 600grit,800grit ** -
(Just putting this out there to confuse things)

This one looked good to me but I don't know anyone who has one
-
I have the Smith's- don't buy. :)
-
i am hooked to this thread. a German academic who knows pretty much all better products and studied the sharpening of knives (he also owns a Swisstool Spirit X!!) is
Am glad that i know some German language.. ::)
He uses lots of Lansky and Spyderco sharpening products. -
Also:
http://www.exduct.com/Special-Limited-Products/SP931D-Precision-Sharpener.htmlsame idea, cheap, should be decent coming from Exduct, diamond stones, I do not know if anybody tried it.
The hones themselves are awesome. Not sure of the exact grit but they made quick work of reprofiling blades however it's downfall is the rail system, made of plastic and would flex too much under use.
The Rods are attached directly via a thread on the back of the hones so they tend to get loose and they don't sit straight. Good for the price but not good in the long run.
From the last q&a on that page:
**
360grit,480grit, 600grit,800grit **Very good coments and options..Thanks,
This exduct system looks good, good price and its diamond stone, but fisrt time I hear about it, there is a good option to try but for know I believe I will go for the Lansky. -
oops, there is much more to sharpening (it's an art, it's science!) than simply buying a fool-proof Smith's, Lansky's or portable knife sharpener. without knowing what you're doing and why, you would could do more harm than good to the edge.
today in the afternoon i found a steel rod in a kitchen drawer and did some simple tests with it on old pocket knives and kitchen knives, and a Ganzo MT. The manufacturing quality of the Ganzo factory edge is a disaster and there was no way to get a perfect 50/50 edge along the blade. i managed to sharpen the knives with free-hand steeling (in a similar uneducated manner as most teenagers on youtube demonstrate their sharpening skills), so i am good. However, i dont really dare to touch up a Swiss made factory edge (which is very sharp already) of the Spirit without knowing anything about it. The above German link is quite helpful; it even points to literature (books on sharpening knives) and has lots of serious videos.A great series of serious videos on sharpening by a real pro is:
http://www.youtube.com/user/MrEZCooking/videosI guess that the subject of sharpening was already discussed at length on this forum and for sure on the many many knife forums on the WWW (i am not going there). Am just saying that restoring the super sharp Spirit edge is a challenge and not as simple as buying a 50$ Lansky kit and following generic instructions from the product manual.
Once one knows the fundamentals, has acquired the practical skills and got all sharpening tools (e.g. in a semi-professional set/kit), one could easily sharpen anything in the household: scythes, scissors, kitchen cutlery, lawn mower, pocket knifes, serrated blades, the special tools of a SAK and SwissTool, etc.
The most general sharpener seems to be the handheld rod and one would want/need different types and coarseness (steel, ceramic, diamond).Gosh.. restoring the Spirit factory edge (i.e. a precision 50/50 grind) with such quality tools could easily cost more than the cost of a new Spirit!
i think i will get just 1 fine "DMT Diafold Serrated Knife Sharpener"-type of rod or the Smith's PP1. Personally i have only very few blades to maintain (Spirit, Minichamp, old pocket knife).. so getting a Lansky or even the Spyderco system is outta line. Maybe i dont even need to resharpen these few blades. Wishful thinking.
Reminds me of flashlights and the topic of rechargeable batteries and their chargers, a wide topic and some users dedicate much much energy and money in it.
Is the Smith's PP1 more or less sufficient for MT's like the Swisstool or does it barely restore the Vic factory edge?
-
The 20 degree setting on the lansky works fine on the Victorinox knives. As long as you take your time and regularly check the edge as you sharpen it's reasonably easy.
Victorinox 111mm Lansky sharpening angle
I got 3 used Victorinox 111mm locking knives, 2 rucksack and a cowboy (pictures later). Their blades could do with some sharpening, so, from anybody using th...
Multitool.Org Forum (forum.multitool.org)
-
If Ganzo is the manufacturer of many rebranded MT's which are sold worldwide, then Taidea might be the manufacturer of sharpening systems which are sold worldwide, possibly rebranded as Lansky or Smith's. For this assertion to verify or check upon, please go to:
http://www.taidea.com/download-3.html ("No. 50", Operation: Down)In the downloaded 2012 PDF catalog browse thru the pages and you'll recognize quite a few products which are sold by Lansky and Smith's (and similar products are seen in Gerber's, Buck's and Schrade's catalog .. so it is rather unclear who the real originator of a particular product model is). Maybe these are knockoff's, maybe not.** If nobody can prove me wrong, i will from here on assume that Taidea is the OEM of some of the products in Lansky's and Smith's sales program.**

If you examine the very professional looking website of Taidea, then it becomes clear that this is a serious big company specialized in manufacturing (or providing) a large variety of nice-looking sharpening tools and i would readily assume that they are, like Ganzo, an original manufacturer or designer of the products which are then rebranded by others, incl. Exduct!
In any case i ordered this here (the shipping costs include tracking number):
http://www.exduct.com/Taidea-Sharpeners/T0931D-Precision-Sharpener.htmlOn the product photos it looks like well-built stuff and Dinodirect, which was one of my favorite flashlight sellers last winter, charges up to 165.99US$, how crazy is that? For our info, on the WWW there was already some talking and even a passaround (which i should have read before placing the order lol; i will read the thread tomorrow).
Once i receive the product and have tested it, i will report back here and let everybody know what i think about this product. Actually i was about to order the Smith's CCD4 3-in-1 sharpening system off ebay but the total would have been the same (~31US$). If the Taidea (rebranded Exduct) system really works well and is of high built quality, then no doubt it beats the Smith's CCD4 at the same price!
-
@dks said:
The 20 degree setting on the lansky works fine on the Victorinox knives. As long as you take your time and regularly check the edge as you sharpen it's reasonably easy.
Victorinox 111mm Lansky sharpening angle
I got 3 used Victorinox 111mm locking knives, 2 rucksack and a cowboy (pictures later). Their blades could do with some sharpening, so, from anybody using th...
Multitool.Org Forum (forum.multitool.org)
Wise words, no matter what system you are using or what blade you are using it on.
-
The 20 degree setting on the lansky works fine on the Victorinox knives. As long as you take your time and regularly check the edge as you sharpen it's reasonably easy.
Victorinox 111mm Lansky sharpening angle
I got 3 used Victorinox 111mm locking knives, 2 rucksack and a cowboy (pictures later). Their blades could do with some sharpening, so, from anybody using th...
Multitool.Org Forum (forum.multitool.org)
Wise words, no matter what system you are using or what blade you are using it on.
Good to know, I have a few Victorinox I would like to re-sharpining for first time.
-
The best tip I have had is to run a marker pen/sharpy over the edge of the blade
This will help you to see where you are removing metal
A good light and magnifier also helps

-
@sparky415 said:
The best tip I have had is to run a marker pen/sharpy over the edge of the blade
This will help you to see where you are removing metal
A good light and magnifier also helps

Good tip also...
Thanks
-
So what exactly is supposed to be happening with the black marked line if i am filing in the perfect angle, i.e. the angle of the factory edge? A line (on the factory edge) may have the width of 2.0mm (milimeters).
If i do one stroke on a precision sharpener (e.g. Lansky system), should the whole 2mm width be affected and get scratched away by the filing movement, or just the very tip (maybe 0.1mm) of the 2mm wide marking?
-
Sorry, I will try to explain
If this is the cross section of a blunt blade and you are sharpening to the exact angle, you will remove the marker and metal (yellow) across all the edge
If you look at the blade from the top (as its in the clamp) you will see a black line where the metal is not touched by the stonedid that make any sense?

-
After it will look like this

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
