Mini Ratchet Chatter
-
@JAfromMn said:
I'm looking forward to seeing what you did up JNnieportyThe Older the Odder the better.
I found some good ones. A titanium-cobalt set from military EOD duties (fixing the robots), a very expensive set of slugging wrenches (which are actually ratchets), and a full set (minus one piece) that I used to repair Abrams tanks. And yes, they're all mini ratchets, made for use in confined spaces. Sadly, Photobucket is giving me a hard time. I'm attempting to load them via ImageShack.
-
I'm looking forward to seeing what you did up JNnieporty
The Older the Odder the better.
I found some good ones. A titanium-cobalt set from military EOD duties (fixing the robots), a very expensive set of slugging wrenches (which are actually ratchets), and a full set (minus one piece) that I used to repair Abrams tanks. And yes, they're all mini ratchets, made for use in confined spaces. Sadly, Photobucket is giving me a hard time. I'm attempting to load them via ImageShack.
I hopoe imageshack workd for you. Sounds like you got some cool ratchets to show.
-
Just found this thread. Some cool little tools here.
Mine is reversible. 60 Chompers!
I love this thing.


Wera 9001 ratchet
I have a idea for my keychain but I haven't put it together yet. Since I have the 1/4" socket drive I plan on carrying a busted 3/8" swivel on my keys with a 1/4" female 3/8" male socket adapter installed.
-
Sweet ratchet lowindo60 tooth

-
Not sure how to edit but I was wrong the p/n is 8001 A
-
Topeak Ratchet Rocket Lite.
In the case. AA battery for size comparison...

The back has a Velcro attachment, and will fit a belt up to 1-1/2" wide...

What you get...

Size...

The strong magnet in the butt is held in with a brass collar...

The finger wheel and reversing lever. The bits can't fall through the back...

Using the finger wheel...

2-1/2" hex bit extension and 2" square socket adapter. These aren't absolutely necessary, but are a welcome addition...

Now I can use 1/4" sockets...

My set-up. There's a bobby pin clipped to the yellow fabric; it acts as a small clamp to remove any stubborn bits. There's a tiny bit of clanking with the extension and adapter, but it's negligible. A Torx T-8 bit is already in the butt of the ratchet...

-
Pittsburgh Tool (Harbor Freight's brand) mini ratchet. $4 and comes with four bits...

A switch rocks back-and-forth to change directions...

This is a Great Neck tool that I got from that Amazonian place for $10, including nine bits and a bit holder...

It's actually a really nice kit for the money, and gives the Topeak Ratchet Rocket some competition. They're the same length...

The finger wheel is identical in size, shape, material, and markings as the Topeak...

However, the wheel is mounted flush with the head of the ratchet, making turning it a bit bothersome...

The hard rubber sleeve actually pulls off if you use enough force, making the tool even more compact. It goes back on as well...

-
This is the set-up I use for the Great Neck, although it will work with any mini ratchet. It's the same size as the Topeak Ratchet Rocket Lite, but twice as thick. It will still fit in a shirt pocket.
Dollar store camera case...


The contents...

Laid out. Nine 1/4" square drive sockets, a bit set that I chose plus a 1/4"-hex-to-1/4"-square adapter, the ratchet itself, and a 2-1/2" hex extension...

Standard 1/4" hex bit...

Hex bit plus extension...

With the adapter, I can use 1/4" square bits, including sockets...

It's my own pocket-sized socket set...

Ready to have your mind blown? The extension, plus the adapter, plus a socket!

-
There's some very nice looking sets of tools in here

-
It look's like I'm not the only one a little nut's over there mini ratchet.
Nice tool's everyone.

-
I looked for a good pocket ratchet a few years ago, and eventually picked up the Chapman one which I think is great. By freak chance I ended up with a Victorinox one shortly after which for me has the edge ergonomically.
They are both really useful little tools though, and I keep one in the basic kit. Usually something along these lines:

-
Chrissy, that o-ring on the LM adapter is for not letting it fall through the chapman or something?
-
Nice set of tools nuphora.
I carry just about the same tool's every day.

If you use the chapman and the pocketwrench 2 on the extender you can make a t handel that work's great
@nuphoria said:
I looked for a good pocket ratchet a few years ago, and eventually picked up the Chapman one which I think is great. By freak chance I ended up with a Victorinox one shortly after which for me has the edge ergonomically.They are both really useful little tools though, and I keep one in the basic kit. Usually something along these lines:

-
The o-ring helps when it's likely to fall the ratchet etc... just found it useful a couple of times so it stayed :)
-
Bumping my old topic
anything new in the mini ratchet world
-
Just ordered a Chapman CM-13 Midget Ratchet thanks to this thread. I've been thinking about which pocket ratchet to buy and all the love for that one here helped make my decision.
-
Now I know what to search for on eBay, looking for one also.

-
@henryhcyap said:
Now I know what to search for on eBay, looking for one also.

I got mine from chapmans site.
-
Now I know what to search for on eBay, looking for one also.

I got mine from chapmans site.
Thanks, will check them out.

-
Make sure you get the bits too. ;)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

