MT.O Challenge Coin
-
(I've spoken to Grant about this idea and he likes it, so consider this the official MT.O challenge coin project thread)
As some of you will be aware, both EDCforums and USN have had challenge coins made for their members, with positive results, capturing something of the essence of these forums in a highly collectable object.
The creation of a multitool.org challenge coin has been discussed a number of times over the years but never got further than that, probably due to the large minimum order and expensive die costs needed being too prohibitive.
However with the help of 3D printing a few prototypes can be made, relatively cheaply, to show off the design and drum up interest before a large expense is committed to, helping such a project gain some momentum.Now all EDCforums have to do to make something fit in with their whole 'every day carry' ethos is to make it fit in their pocket but we are a multitool forum and that means functions.
Our coin must do something other than look pretty, so this is what i came up with:
Ignore the MT.O pattern for now as it's just a place holder.
The tool has:
A 1/4" hex bit driver,
A knurled and scalloped outer edge to improve grip,
A 0.127" (3.23mm) spoke wrench,
A 0.130" (3.30mm) spoke wrench,
A 0.136" (3.45mm) spoke wrench,
The coins dimensions are 40mm in diameter and 3mm thick.And now for the challenge bit......
What other functions could be added to such a coin?
What designs would you like to see on each face?If your interested in such a coin then please get involved with your ideas and creativity.
You forum needs you!PS. Raukodur's multitool innovation forum idea would be the perfect place for this thread to stop it getting lost in all the other general discussions.
-
Maybe you could add screwdriver tips between the spoke wrenches? Might make it less comfortable though but it'd add some more uses?
-
Screwdrivers and Metric sized hex or wrench type things please :D
-
I think it should be kept as simple as possible, so a hex in the middle and rounded edges (like the ones on top/no spoke wrenches) all the way around. Nothing more.. :)
-
-
@AHB said:
I think it should be kept as simple as possible, so a hex in the middle and rounded edges (like the ones on top/no spoke wrenches) all the way around. Nothing more.. :)This, but make the edge like the pocket screwdriver so it can be used on different sizes of screws.

Maybe lower the 1/4 hole, place a double sided leatherman flat/phillips bit in the middle and the full name on top.


-
This does depend on whether we want to go for simple design, or cram as much as we can into it.
And if you go with the latter option, it depends if you want to be a jack of all trades or a master of one, i.e. do you want it to have lots of different functions but with limited functionality, or just have one function, but do it very well.
Personally, I dislike redundancy, so I already have keyring size equipment with screwdrivers and wrenches, etc. What I would really like, is something very different and imaginative. And you know what? A good alternative to that is to have a very aesthetically pleasing design and motif, and forget about functions, given that we already have most all of the functions we would end up putting on this.
-
Put a magnet on one end, or magnetize it. Set it upon a floating item and have a functional compass.
Then if the coin had a hole through it, it could serve as a part retrieval item. Dangle from a string and the magnetic end could fetch the item.
If you wanted to go even classier, put a small tritium vial on that magnetic/north end. Or a glow in the dark marker?If you set the center as a normal hex bit driver, taper it on one side. That way when used as a hex driver the hex bit will have a shoulder to to help keep it pressed on the screw. Too many hex holes are not tapered and you have to fight to keep the bit in the holder.
One tool I would like to see on one end, if you are going that route, is a valve core remover/tightener.
Another thing could add is a mini-bit driver to hold an eye-glass bit from Leatherman.

Guess it depends how unique you want the coin stand out from the crowd. :D
-
So thinking about this a bit one, one possible idea:
Instead of a 'coin' what if it was more like a 'ring' and so could functional like a keyring, with either a solid or hollow centre.
I have tried to make a sketch of both designs. The blue area would be where the logo(s) could go.
I do like the idea of some sort of glow in the dark marker.
<a href="http://postimage.org/image/g3lxux5tl/" target="_blank" rel="noopener noreferrer"><img src="http://s12.postimage.org/g3lxux5tl/MTO_ring_idea_1a_page_1.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
-
First hunch I was thinking keyring-coin as well, to attach all your goodies to.
Whatever, I love to have a MTO challenge coin

-
I think it should be kept as simple as possible, so a hex in the middle and rounded edges (like the ones on top/no spoke wrenches) all the way around. Nothing more.. :)
This, but make the edge like the pocket screwdriver so it can be used on different sizes of screws.

Maybe lower the 1/4 hole, place a double sided leatherman flat/phillips bit in the middle and the full name on top.

I really like this idea enki_ck
I do not ride bikes so a spoke wrench does not attract me.
If it is a wrench I like Nuphoria's idea with metric or standard slots. -
I think it should be kept as simple as possible, so a hex in the middle and rounded edges (like the ones on top/no spoke wrenches) all the way around. Nothing more.. :)
This, but make the edge like the pocket screwdriver so it can be used on different sizes of screws.

Maybe lower the 1/4 hole, place a double sided leatherman flat/phillips bit in the middle and the full name on top.

I really like this idea enki_ck
I do not ride bikes so a spoke wrench does not attract me.
If it is a wrench I like Nuphoria's idea with metric or standard slots.+1, I like the coin driver too.
-
I think it should be kept as simple as possible, so a hex in the middle and rounded edges (like the ones on top/no spoke wrenches) all the way around. Nothing more.. :)
This, but make the edge like the pocket screwdriver so it can be used on different sizes of screws.

Maybe lower the 1/4 hole, place a double sided leatherman flat/phillips bit in the middle and the full name on top.

I really like this idea enki_ck
I do not ride bikes so a spoke wrench does not attract me.
If it is a wrench I like Nuphoria's idea with metric or standard slots.+1, I like the coin driver too.
+1 From me also for the coin drive, simple and useful. ;)
-
[quote author=AHB link=topic=43150.msg693174#msg693174 date=1361102735]
I think it should be kept as simple as possible, so a hex in the middle and rounded edges (like the ones on top/no spoke wrenches) all the way around. Nothing more.. :)This, but make the edge like the pocket screwdriver so it can be used on different sizes of screws.

Maybe lower the 1/4 hole, place a double sided leatherman flat/phillips bit in the middle and the full name on top.

I really like this idea enki_ck
I do not ride bikes so a spoke wrench does not attract me.
If it is a wrench I like Nuphoria's idea with metric or standard slots.+1, I like the coin driver too.
+1 From me also for the coin drive, simple and useful. ;)
[/quote]That would also make it easier to carry on a spring clip on a keyring

-
im perfectly happy with the spoke wrench design! where can i buy one :D
-
May I ask, what is the coin drive for? Does it have any function over a normal screwdriver I am not aware of?
-
The coin screwdriver could have a copyright infringement issue too. Would not want anything negative to come from that.
-
I have in my pocket is always a lot of multi tool. I do not need a coin tool. But if the coin measurement. I thought design. (all the while not exact) coin has five dimensions. 1 - stick the coin base point, and watch the gap size.
2 - piece tapered in cross section, and if it vsavit in the slot 2 on a scale to know the width of the slit
3-find sheet thickness of 0.5 mm, 4 mm.
4 - number of holes the size. The back of the dial. If you insert a pencil into the center and roll edge of the coin, on a scale to find distance.
<a href="http://www.radikal.ru" target="_blank" rel="noopener noreferrer"><img src="http://s002.radikal.ru/i200/1302/be/5b27e2d07747.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
<a href="http://www.radikal.ru" target="_blank" rel="noopener noreferrer"><img src="http://s40.radikal.ru/i088/1302/1a/7b5215881231.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a> -
I think this discussion is more about ideas for a MT.O Onepiece tool than making an actual Challenge Coin.

I love the idea of real Challenge Coin, but a traditional Coin has no practical uses but is a constant reminder of how things are done at MT.O.
-
I like the idea of magnetizing it and having just one hole through the center. Maybe something glow in the dark, that would be cool. Really cool idea guys!
Sent from my own private Idaho
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

