Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Wenger universal wrench replacing Magnifier

Scheduled Pinned Locked Moved The Mod Squad
26 Posts 1 Posters 6.3k Views
  1. Home
  2. The Mod Squad
  3. Wenger universal wrench replacing Magnifier
Wenger universal wrench replacing Magnifier
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • HankSolon Offline
    HankSolon
    Posts: 588
    HankSolon Offline
    HankSolon
    wrote on last edited by
    #12 Quote Reply

      @TurkTeen said:
      I have always wanted to have the inline phillips, mag glass and the LED on a same SAK...this might be the solution!

      Just pair the wrench with the phillips; and the LED with the mag...

      This is a very possible setup. My extended swisschamp has a LED paired with a mag. An additional layer with phillips and wrench is reasonable. But don't underestimate the width of these 4 tools. Will result in a fat knife. ;)

      1 Reply Last reply
      • Syph007 Offline
        Syph007
        Global Moderators
        Posts: 9,842
        Syph007 Offline
        Syph007
        Global Moderators
        wrote on last edited by
        #13 Quote Reply

          I hope the wrench part wont be discontinued with Vic absorbing the wenger lineup. If it is, I think that might be the next custom part I make up with the next waterjet run.

          PM me or email sakmodder [at] gmail . com if you are looking for custom SAK work.

          Modding thread : Here
          Website : WWW.SAKModder.com
          Facebook : SAKModder
          Instagram : robertjlessard
          Youtube : www.youtube.com/robertjlessard

          1 Reply Last reply
          • HankSolon Offline
            HankSolon
            Posts: 588
            HankSolon Offline
            HankSolon
            wrote on last edited by HankSolon
            #14 Quote Reply

              @Syph007 said:
              I hope the wrench part wont be discontinued with Vic absorbing the wenger lineup. If it is, I think that might be the next custom part I make up with the next waterjet run.

              Will hope so too. A custom wrench... hmm sounds good, maybe you can adjust it a bit, so that a standard phillips/mag spring will fit too.

              But again... there should be a test run made in Germany, too. Too tired to find a good reason, but there is one. :-D

              1 Reply Last reply
              • ironraven Offline
                ironraven
                Posts: 3,071
                ironraven Offline
                ironraven
                wrote on last edited by
                #15 Quote Reply

                  That would be an excellent layer to add to a Compact. Excellent work!

                  "Even if it is only the handful of people I meet on the street, or in my home, I can still protect them with this one sword" Kenshin Himura

                  Necessity is the mother of invention. If you're not ready, it's "a mother". If you are, it's "mom".

                  "I love democracy" Sheev Palpatine, upon his election to Chancellor.

                  1 Reply Last reply
                  • Sr.Multiherramienta Offline
                    Sr.Multiherramienta
                    Posts: 76
                    Sr.Multiherramienta Offline
                    Sr.Multiherramienta
                    wrote on last edited by
                    #16 Quote Reply

                      Really interesting. Is nearly the perfect Champ.

                      http://multi-herramientas.blogspot.com/
                      The site in spanish about multitools, swiss army knives and other gadgets.

                      1 Reply Last reply
                      • Quartz Offline
                        Quartz
                        Posts: 240
                        Quartz Offline
                        Quartz
                        wrote on last edited by
                        #17 Quote Reply

                          Question:

                          I have a wrench I pulled out of my Wenger because I thought it was useless. It's not wide enough to fit over any of the real heavy duty bolts or couplers I encounter, and the stuff small enough to fit can be better serviced by pliers. Why do people like this tool? What am I missing?

                          1 Reply Last reply
                          • Raukodur Offline
                            Raukodur
                            Posts: 1,614
                            Raukodur Offline
                            Raukodur
                            wrote on last edited by
                            #18 Quote Reply

                              @Quartz said:
                              Question:

                              I have a wrench I pulled out of my Wenger because I thought it was useless. It's not wide enough to fit over any of the real heavy duty bolts or couplers I encounter, and the stuff small enough to fit can be better serviced by pliers. Why do people like this tool? What am I missing?

                              I am thinking the exact same question.

                              1 Reply Last reply
                              • Syph007 Offline
                                Syph007
                                Global Moderators
                                Posts: 9,842
                                Syph007 Offline
                                Syph007
                                Global Moderators
                                wrote on last edited by
                                #19 Quote Reply

                                  @Raukodur said:

                                  @Quartz said:

                                  Question:

                                  I have a wrench I pulled out of my Wenger because I thought it was useless. It's not wide enough to fit over any of the real heavy duty bolts or couplers I encounter, and the stuff small enough to fit can be better serviced by pliers. Why do people like this tool? What am I missing?

                                  I am thinking the exact same question.

                                  Works on lots of little bolts Ive come accorss. There are many different versions of it, some have more fine steps to work on more bolts. The biggest perk its its metal and can fit accross from a phillips and not have that awful plastic magnifier. ANYTHING is better than that piece of plastic in a nice SAK.

                                  PM me or email sakmodder [at] gmail . com if you are looking for custom SAK work.

                                  Modding thread : Here
                                  Website : WWW.SAKModder.com
                                  Facebook : SAKModder
                                  Instagram : robertjlessard
                                  Youtube : www.youtube.com/robertjlessard

                                  1 Reply Last reply
                                  • Quartz Offline
                                    Quartz
                                    Posts: 240
                                    Quartz Offline
                                    Quartz
                                    wrote on last edited by
                                    #20 Quote Reply

                                      @Syph007 said:
                                      Works on lots of little bolts Ive come accorss.

                                      The "little" is kinda my issue. It's built super thick like it's designed for heavy duty torque, but there's no way nuts small enough to fit in it will need more torque than what the pliers can deliver. To add insult to injury, on most Wenger's the wrench is somewhere in the middle layers and they have those double-thick evo scales, meaning you can't even get it close enough to go around any bolts in the first place.

                                      @Syph007 said:
                                      ANYTHING is better than that piece of plastic in a nice SAK.

                                      Eh, I dunno it's any worse than the corkscrew, which is basically just an eyeglasses-screwdriver-container. I've used the mag on an Explorer once or twice to figure out which sub-pixel pattern an LCD was using, whereas the wrench doesn't seem to be usable at all.

                                      1 Reply Last reply
                                      • HankSolon Offline
                                        HankSolon
                                        Posts: 588
                                        HankSolon Offline
                                        HankSolon
                                        wrote on last edited by
                                        #21 Quote Reply

                                          As I thought. The new mag/phillips backspring allows an easy replacement of the wenger wrench. As seen on the pics below.

                                          The only issue: I had just a new (but not the newest!!) phillips to try. So the spring for my version of the phillips would need some grind job. I assume that the effect on the (good till strong) snap of the wrench will result in a perfect snap, however.

                                          ImageUploadedByTapatalk1373306280.854730.jpg

                                          1 Reply Last reply
                                          • HankSolon Offline
                                            HankSolon
                                            Posts: 588
                                            HankSolon Offline
                                            HankSolon
                                            wrote on last edited by
                                            #22 Quote Reply

                                              missing pics

                                              ImageUploadedByTapatalk1373306323.557129.jpg

                                              ImageUploadedByTapatalk1373306333.646854.jpg

                                              ImageUploadedByTapatalk1373306343.765947.jpg

                                              1 Reply Last reply
                                              • HankSolon Offline
                                                HankSolon
                                                Posts: 588
                                                HankSolon Offline
                                                HankSolon
                                                wrote on last edited by
                                                #23 Quote Reply

                                                  Improved stopper using a broken scissor.

                                                  1 Reply Last reply
                                                  • Fattsgalore Offline
                                                    Fattsgalore
                                                    Posts: 883
                                                    Fattsgalore Offline
                                                    Fattsgalore
                                                    wrote on last edited by
                                                    #24 Quote Reply

                                                      @Nhoj said:
                                                      This mod might become very popular. I have heard lots of people here wanting a universal wrench in a vic. Is that the new or old phillips?

                                                      What he said. I could use that little wrench over the mag or LED.
                                                      To bad I don't have SAKs to experiment with.

                                                      It the wrench and inline phillips the same thickness?

                                                      Bookmarked...

                                                      1 Reply Last reply
                                                      • HankSolon Offline
                                                        HankSolon
                                                        Posts: 588
                                                        HankSolon Offline
                                                        HankSolon
                                                        wrote on last edited by HankSolon
                                                        #25 Quote Reply

                                                          Mag AND wrench won't work (they are on the same side).

                                                          LED AND wrench won't work, too. The old style spring (for phillips/LED - MAG) won't give you enough snap on the wrench. An old scissors spring (without backtool) might help but it would need some modding to get the fit in here (and I'm not sure, if the LED would "snap" in closed position, even if you mod the area around the middle pin).

                                                          That said: scissors, wrench, LED and phillips almost have the same width. So no spacer is needed here.

                                                          I used the new phillips/Mag spring at the mod here, since
                                                          [list type=decimal]

                                                          • the new spring is something, what I can get very cheap

                                                          • the wrench side needs no special modding!!!

                                                          • older phillips are easier to get

                                                          EDIT -> added additional explanations, see the picture below:

                                                          2014-03-27 wrench explanation.jpg

                                                          1 Reply Last reply

                                                          Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                          Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                          With your input, this post could be even better 💗

                                                          Register Login

                                                          • 1
                                                          • 2
                                                          1. Home
                                                          2. The Mod Squad
                                                          3. Wenger universal wrench replacing Magnifier
                                                          Reply
                                                          • Reply as topic
                                                          Log in to reply
                                                          COMMUNITY LINKS
                                                          EDC-TV SAKWiki GearFeed SAKSelector
                                                          Operational Funds

                                                          Help us keep the Unworkable working!

                                                          Make A Donation
                                                          November Goal: $300.00
                                                          Due Date: Nov 30
                                                          Total Receipts: $0.00
                                                          Below Goal: $300.00
                                                          0% funded
                                                          • Login

                                                          • Don't have an account? Register

                                                          • Login or register to search.
                                                          • First post
                                                            Last post
                                                          0