Multitool.org Forum
+-

Hello Lurker! Remove this ad and much more by logging in.


Quarter inch drive for SAKs!

kirk13 · 7 · 1838
« previous next »
Pages: 1   Go Down

00 Offline kirk13

  • Admin Team
  • *
  • *
  • Zombie Apprentice
  • *
    • Posts: 15,281
Quarter inch drive for SAKs!
on: August 24, 2011, 09:05:04 PM
I've always been fustrated by how few SAKs have Philips drivers.Its very rare at work to come across flat headed screws.I've seen other members who've done mods to fit 1/4 inch driver socket to the flat driver/caplifters on thier SAKs,but this is my lazy man variation!

Mix up enough 2 part epoxy putty to fill the driver side of the socket,and well fill it!Close to hand you should have a SAK with the driver/caplifter lubricated with vasaline(putty has difficulty gripping on to the vasaline :D),insert the caplifter firmly and quickly(this is sounding so BAD),and gently withdraw.

This should give a tight fit(once the putty is dry of course).And then you can use philips,hex and torx bits to your hearts content!

Pix will follow!
There is no beginning,or ending,and for this we are thankful,cos now is hard enough to understand!
Merit Badges Start a thread with photos of at least five different colored ALOX models in your collection Start a new thread and post a photo of the discontinued sak/mt for thirty (30) consecutive days. Start a new thread with a photo of a modded knife or multitool with your EDC Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Start a new thread with a photo of custom or non standard SAK scales in your collection Start a new thread with photos of a Japanese made PST in your collection

00 Offline kirk13

  • Admin Team
  • *
  • *
  • Zombie Apprentice
  • *
    • Posts: 15,281
Re: Quarter inch drive for SAKs!
Reply #1 on: September 01, 2011, 05:17:31 PM
Better late than never,heres the pix:




Normal socket with one set up for Wenger cap lifter(maked with W),and for Vic(marked with the V :think:)

And fitted


There is no beginning,or ending,and for this we are thankful,cos now is hard enough to understand!
Merit Badges Start a thread with photos of at least five different colored ALOX models in your collection Start a new thread and post a photo of the discontinued sak/mt for thirty (30) consecutive days. Start a new thread with a photo of a modded knife or multitool with your EDC Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Start a new thread with a photo of custom or non standard SAK scales in your collection Start a new thread with photos of a Japanese made PST in your collection

gb Offline Screwtape

  • Hero Member
  • *****
    • Posts: 987
  • I am the Toast King!!
Re: Quarter inch drive for SAKs!
Reply #2 on: September 01, 2011, 06:48:37 PM
Nice idea, I thoroughly agree that it would be nice to see more SAK with cross head drivers, particularly the slimmer ones or perhaps an alox model.
"Hello! I am the Toast King and I rule over the Moon!"

us Offline bushidomosquito

  • Hero Member
  • *****
    • Posts: 660
Re: Quarter inch drive for SAKs!
Reply #3 on: September 08, 2011, 10:09:34 PM
Well that's nifty as hell.  :tu:

Now figure out how to store it under the scale next to the toothpick and you'll be good to go!  :D
Sent from my Glock 23 using Doubletaptalk

ca Offline Metropolicity

  • *
  • No Life Club
  • ******
    • Posts: 3,797
  • Hack Virtuoso
Re: Quarter inch drive for SAKs!
Reply #4 on: September 08, 2011, 11:23:35 PM
Quote from: bushidomosquito on September 08, 2011, 10:09:34 PM
Well that's nifty as hell.  :tu:

Now figure out how to store it under the scale next to the toothpick and you'll be good to go!  :D

Let me know how you are folding time and space...I could use it for the tiny house we live in :)
Why stop now?

Visit the whole Skinth family here: http://www.skinthsolutions.com

Keep up with The Skinths on Facebook: http://www.facebook.com/SkinthSolutions

Shapeways - Metro's Q-branch:
http://www.shapeways.com/shops/metro-qbranch

PayPal: metrogradegoods [at} gmail. com

us Offline bushidomosquito

  • Hero Member
  • *****
    • Posts: 660
Re: Quarter inch drive for SAKs!
Reply #5 on: September 08, 2011, 11:51:33 PM
The new Victorinox Tardis! Maybe I could squeeze a sonic screwdriver in there too.
Sent from my Glock 23 using Doubletaptalk

00 Offline kirk13

  • Admin Team
  • *
  • *
  • Zombie Apprentice
  • *
    • Posts: 15,281
Re: Quarter inch drive for SAKs!
Reply #6 on: September 09, 2011, 01:18:28 AM
Quote from: bushidomosquito on September 08, 2011, 11:51:33 PM
The new Victorinox Tardis! Maybe I could squeeze a sonic screwdriver in there too.

Dont joke!I have a lady freind whose edc is a Sonic Screwdriver(takes 1/4 inch bits) and a Vic Manager I gave her
There is no beginning,or ending,and for this we are thankful,cos now is hard enough to understand!
Merit Badges Start a thread with photos of at least five different colored ALOX models in your collection Start a new thread and post a photo of the discontinued sak/mt for thirty (30) consecutive days. Start a new thread with a photo of a modded knife or multitool with your EDC Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Start a new thread with a photo of custom or non standard SAK scales in your collection Start a new thread with photos of a Japanese made PST in your collection

Pages: 1   Go Up
 

Donations
Operational Funds

Help us keep the Unworkable working!
Donate with PayPal!
June Goal: $300.00
Due Date: Jun 30
Total Receipts: $81.95
PayPal Fees: $4.26
Net Balance: $77.69
Below Goal: $222.31
Site Currency: USD
26% 
June Donations

Community Links
Multitool.org
Multitool Gallery
Multitool Encyclopedia
SAKWiki
Swiss Army Knights

Powered by EzPortal