Multitool.org Forum
+-

Hello Lurker! Remove this ad and much more by logging in.


SOG parts in a LM

nj2656 · 5 · 1546
« previous next »
Pages: 1   Go Down

us Offline nj2656

  • Full Member
  • ***
    • Posts: 145
SOG parts in a LM
on: October 01, 2012, 05:49:19 AM
Are SOG parts compatible with LMMT's? Retired my PST II from my duty belt. I have an older Wave that I don't carry. Looking at the V cutter to change out with the standard blade. I carry a large folder so it's not really needed.

us Offline rdub934

  • No Life Club
  • ******
    • Posts: 1,991
  • Without POL, pilots are pedestrians
Re: SOG parts in a LM
Reply #1 on: October 04, 2012, 05:22:05 AM
I am curious about this myself. I would like to put the SOG awl into my Wave.
"I wanna introduce you to a very personal friend of mine. This is an M41A pulse rifle. Ten millimeter with over-and-under thirty millimeter pump action grenade launcher." - Cpl Hicks
Merit Badges Start a new thread including a photo of shooting at least two (2) different firearms and at least one (1) photo of target (firearms) Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Start a new thread with a photo showing the axe in use Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread showing photos of at least 3 different sporks in use Start a new thread demonstrating paracord knot tying Must start a thread showing a photo of at least three BO tools Start a new thread and post a photo of a flashlight as part of your EDC Must start new thread with photos of multitools (Magazine/Catalogue type photos)

gb Offline nuphoria

  • Ambidangerous Mistress of Mod
  • Admin Team
  • *
  • Zombie Apprentice
  • *
    • Posts: 15,038
  • I'm not all bad, I'm just drawn that way.
Re: SOG parts in a LM
Reply #2 on: October 04, 2012, 02:07:58 PM
I've seen it done here, but I think it involved a little grinding to reshape the tools.
A dyslexic man walks in to a bra...

All my music for free: http://soundcloud.com/chrissyvandyke

gb Offline AimlessWanderer

  • *
  • Zombie Apprentice
  • ********
    • Posts: 17,518
  • I'm not a pessimist, I'm an experienced optimist!
Re: SOG parts in a LM
Reply #3 on: October 04, 2012, 03:33:28 PM
I tried looking at a SOG saw in a PST II and that was a no-go, however I was successful in putting the PST II's scissors and file in a SOG PPP. Once you start looking at the more modern tools, you're OK with such as the Kick but the locking notch needs widening on each SOG implement to get it to lock on a Blast or Wave. Pivot and tang are otherwise OK


The cantankerous but occasionally useful member, formally known as 50ft-trad

us Offline nj2656

  • Full Member
  • ***
    • Posts: 145
Re: SOG parts in a LM
Reply #4 on: October 04, 2012, 04:17:02 PM
Locking notch is not a problem. I was just wondering if the pivots were compatible.

Pages: 1   Go Up
 

Donations
Operational Funds

Help us keep the Unworkable working!
Donate with PayPal!
May Goal: $300.00
Due Date: May 31
Total Receipts: $86.45
PayPal Fees: $5.07
Net Balance: $81.38
Below Goal: $218.62
Site Currency: USD
27% 
May Donations

Community Links
Multitool.org
Multitool Gallery
Multitool Encyclopedia
SAKWiki
Swiss Army Knights

Powered by EzPortal