Multitool.org Forum
+-

Hello Lurker! Remove this ad and much more by logging in.


Electro Etching?

Whoey · 4 · 1276
« previous next »
Pages: 1   Go Down

fr Offline Whoey

  • Administrator
  • *
  • Zombie Apprentice
  • *
    • Posts: 13,122
  • I am geek, hear me code
Electro Etching?
on: October 28, 2013, 08:45:01 PM
An enterprising member of the Australian Blade Forum came up with this fancy thing (as featured on Hack a day):

http://hackaday.com/2013/10/27/electrochemical-etching-with-a-microcontroller/

rather cool imho, and I'd be tempted to get one myself... obviously its usefulness would run out once I'd tagged all my tools since I'm not a fabricator, but it would be a rather neat thing to have! I'm sure some of you would have even better uses for it...
The difficult we do immediately, the impossible takes a little longer.
Merit Badges Must start a thread with a photo of at least five (5) of your watches

hr Offline enki_ck

  • Global Moderator
  • *
  • Absolute Zombie Club
  • *
    • Posts: 20,935
  • I may get older but I refuse to grow up.
Re: Electro Etching?
Reply #1 on: October 28, 2013, 10:43:51 PM
Looks very interesting but $450 for the assembled device is a bit ;) out of my price range. :D $180 only gets you parts that you need to assemble/solder yourself. It was interesting to watch though. :cheers:
Merit Badges Must start a thread with a photo of at least five (5) of your watches Must update or add a page on SAKWiki Start a thread with photos of at least 5 different Juice models in your collection Start a new thread with a photo of a modded knife or multitool with your EDC Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Start a new thread and post a photo of a flashlight as part of your EDC Must buy something on EDCSource Must update or add a page on the Multitool.org Multitool Encyclopedia Must put something in order and provide link to the post. Start a new thread with a photo of custom or non standard SAK scales in your collection

fr Offline Whoey

  • Administrator
  • *
  • Zombie Apprentice
  • *
    • Posts: 13,122
  • I am geek, hear me code
Re: Electro Etching?
Reply #2 on: October 28, 2013, 10:58:05 PM
From what I read in the build thread it's 160$aud for the unassembled kit which is soldered, you just have to mount the board yourself... Check the Australian blade forum link

Sent from my Nexus 7 using Tapatalk 4
The difficult we do immediately, the impossible takes a little longer.
Merit Badges Must start a thread with a photo of at least five (5) of your watches

hr Offline enki_ck

  • Global Moderator
  • *
  • Absolute Zombie Club
  • *
    • Posts: 20,935
  • I may get older but I refuse to grow up.
Re: Electro Etching?
Reply #3 on: October 28, 2013, 11:10:52 PM
Yes I did, but I only read to the first price quote,  Post #14.  :doh: He reduced the price later and added the soldering.
Merit Badges Must start a thread with a photo of at least five (5) of your watches Must update or add a page on SAKWiki Start a thread with photos of at least 5 different Juice models in your collection Start a new thread with a photo of a modded knife or multitool with your EDC Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Start a new thread and post a photo of a flashlight as part of your EDC Must buy something on EDCSource Must update or add a page on the Multitool.org Multitool Encyclopedia Must put something in order and provide link to the post. Start a new thread with a photo of custom or non standard SAK scales in your collection

Pages: 1   Go Up
 

Donations
Operational Funds

Help us keep the Unworkable working!
Donate with PayPal!
May Goal: $300.00
Due Date: May 31
Total Receipts: $86.45
PayPal Fees: $5.07
Net Balance: $81.38
Below Goal: $218.62
Site Currency: USD
27% 
May Donations

Community Links
Multitool.org
Multitool Gallery
Multitool Encyclopedia
SAKWiki
Swiss Army Knights

Powered by EzPortal