Multitool.org Forum
+-

Hello Lurker! Remove this ad and much more by logging in.


Wave manufacturing date

Antonio_s2 · 25 · 9698
« previous next »
Pages: 1   Go Down

us Offline Antonio_s2

  • Newbie
  • *
    • Posts: 17
Wave manufacturing date
on: July 24, 2017, 04:46:31 AM
Just got my second learherman tool, the wave. And I went to look at when it was Made and it says 917. That can't be right unless that's not the manufacturing date. Is there a manufacturing date stamped somewhere else?

« Last Edit: July 24, 2017, 04:53:28 AM by Antonio_s2 »
"It's not what you take when you leave this world behind you, it's what you leave behind you when you go" - Randy Travis

us Offline aluminated

  • *
  • Sr. Member
  • ****
    • Posts: 286
Re: Wave manufacturing date
Reply #1 on: July 24, 2017, 05:06:36 AM
New Wave date stamps are on the inside of the handle on the side, not on the bottom.
I.e. stamped on the vertical, not on the horizontal.
« Last Edit: July 24, 2017, 05:08:17 AM by aluminated »
Merit Badges Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Must start a thread showing a photo of at least three BO tools

us Offline Antonio_s2

  • Newbie
  • *
    • Posts: 17
Re: Wave manufacturing date
Reply #2 on: July 24, 2017, 05:12:51 AM
Quote from: aluminated on July 24, 2017, 05:06:36 AM
New Wave date stamps are on the inside of the handle on the side, not on the bottom.
I.e. stamped on the vertical, not on the horizontal.


Yep that's where I was looking. It says 41 in little letters and 917 after. I also just noticed it says 817 on the other handle
"It's not what you take when you leave this world behind you, it's what you leave behind you when you go" - Randy Travis

us Offline aluminated

  • *
  • Sr. Member
  • ****
    • Posts: 286
Re: Wave manufacturing date
Reply #3 on: July 24, 2017, 05:36:54 AM
It will definitely be a 4-digit number.
Merit Badges Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Must start a thread showing a photo of at least three BO tools

us Offline Aloha

  • Global Moderator
  • *
  • Point Of No Return
  • *
    • Posts: 31,235
Re: Wave manufacturing date
Reply #4 on: July 24, 2017, 05:55:16 AM
Could also be a very lightly stamped 0.  I've had a few that were incredibly hard to see the date stamp.  If its a new Wave with the date code on the side then theres a good chance the 0 is just very light.  Zoidberg uses a flashlight to illuminate the area, I also use this method along with my Swisschamp mag glass. 
Esse Quam Videri
Merit Badges Start a new thread and post a photo of the pen for thirty (30) consecutive days. Start a new thread and post a photo of a traditional folder for thirty (30) consecutive days. Take part in the christmas pool or a rak type giveaway. Those wanting to say thank you for a rak may also nominate for the santa. Must start a thread showing a photo of at least eight BO tools Start a new thread showing photos of your outdoor cooking Must have a review written in the proper format and posted on the Main Site Start a new thread with photos of camping, including those showing preferred camping equipment Start a new thread and post a photo of a flashlight as part of your EDC Start a new thread and post a picture of fire making kit or fire with a multitool Start a new thread with photos of a Japanese made PST in your collection Start a thread with photos of at least 5 different Juice models in your collection Start a thread with a photo of at least ten OPT's in your collection

us Offline aluminated

  • *
  • Sr. Member
  • ****
    • Posts: 286
Re: Wave manufacturing date
Reply #5 on: July 24, 2017, 06:13:10 AM
Quote from: Aloha007 on July 24, 2017, 05:55:16 AM
Could also be a very lightly stamped 0.  I've had a few that were incredibly hard to see the date stamp.  If its a new Wave with the date code on the side then theres a good chance the 0 is just very light.  Zoidberg uses a flashlight to illuminate the area, I also use this method along with my Swisschamp mag glass.
But we haven't reached 0817 or 0917 yet!
Merit Badges Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Must start a thread showing a photo of at least three BO tools

us Offline Aloha

  • Global Moderator
  • *
  • Point Of No Return
  • *
    • Posts: 31,235
Re: Wave manufacturing date
Reply #6 on: July 24, 2017, 06:47:38 AM
 :facepalm:
Esse Quam Videri
Merit Badges Start a new thread and post a photo of the pen for thirty (30) consecutive days. Start a new thread and post a photo of a traditional folder for thirty (30) consecutive days. Take part in the christmas pool or a rak type giveaway. Those wanting to say thank you for a rak may also nominate for the santa. Must start a thread showing a photo of at least eight BO tools Start a new thread showing photos of your outdoor cooking Must have a review written in the proper format and posted on the Main Site Start a new thread with photos of camping, including those showing preferred camping equipment Start a new thread and post a photo of a flashlight as part of your EDC Start a new thread and post a picture of fire making kit or fire with a multitool Start a new thread with photos of a Japanese made PST in your collection Start a thread with photos of at least 5 different Juice models in your collection Start a thread with a photo of at least ten OPT's in your collection

us Offline Aloha

  • Global Moderator
  • *
  • Point Of No Return
  • *
    • Posts: 31,235
Re: Wave manufacturing date
Reply #7 on: July 24, 2017, 06:48:34 AM
I was really thinking they were ahead of production since its only a month or 2. 
Esse Quam Videri
Merit Badges Start a new thread and post a photo of the pen for thirty (30) consecutive days. Start a new thread and post a photo of a traditional folder for thirty (30) consecutive days. Take part in the christmas pool or a rak type giveaway. Those wanting to say thank you for a rak may also nominate for the santa. Must start a thread showing a photo of at least eight BO tools Start a new thread showing photos of your outdoor cooking Must have a review written in the proper format and posted on the Main Site Start a new thread with photos of camping, including those showing preferred camping equipment Start a new thread and post a photo of a flashlight as part of your EDC Start a new thread and post a picture of fire making kit or fire with a multitool Start a new thread with photos of a Japanese made PST in your collection Start a thread with photos of at least 5 different Juice models in your collection Start a thread with a photo of at least ten OPT's in your collection

us Offline Antonio_s2

  • Newbie
  • *
    • Posts: 17
Re: Wave manufacturing date
Reply #8 on: July 24, 2017, 07:28:19 AM
Quote from: Aloha007 on July 24, 2017, 06:48:34 AM
I was really thinking they were ahead of production since its only a month or 2.

This sounds reasonable, i don't know of any other explanation
"It's not what you take when you leave this world behind you, it's what you leave behind you when you go" - Randy Travis

us Offline Antonio_s2

  • Newbie
  • *
    • Posts: 17
Re: Wave manufacturing date
Reply #9 on: July 24, 2017, 07:33:24 AM
Quote from: Aloha007 on July 24, 2017, 05:55:16 AM
Could also be a very lightly stamped 0.  I've had a few that were incredibly hard to see the date stamp.  If its a new Wave with the date code on the side then theres a good chance the 0 is just very light.  Zoidberg uses a flashlight to illuminate the area, I also use this method along with my Swisschamp mag glass.

I don't think this could be it as there's no room for the 0 as the number 1 In front of the nice is pretty close. I think my wave was made on a monday!
"It's not what you take when you leave this world behind you, it's what you leave behind you when you go" - Randy Travis

nz Offline zoidberg

  • Point Of No Return
  • **********
    • Posts: 37,929
Re: Wave manufacturing date
Reply #10 on: July 24, 2017, 12:35:52 PM
 :worthless:

us Offline Aloha

  • Global Moderator
  • *
  • Point Of No Return
  • *
    • Posts: 31,235
Re: Wave manufacturing date
Reply #11 on: July 24, 2017, 03:10:20 PM
Quote from: Antonio_s2 on July 24, 2017, 07:33:24 AM
Quote from: Aloha007 on July 24, 2017, 05:55:16 AM
Could also be a very lightly stamped 0.  I've had a few that were incredibly hard to see the date stamp.  If its a new Wave with the date code on the side then theres a good chance the 0 is just very light.  Zoidberg uses a flashlight to illuminate the area, I also use this method along with my Swisschamp mag glass.

I don't think this could be it as there's no room for the 0 as the number 1 In front of the nice is pretty close. I think my wave was made on a monday!

Wouldn't be the first time Monday morning production turned out weirdness. 
Esse Quam Videri
Merit Badges Start a new thread and post a photo of the pen for thirty (30) consecutive days. Start a new thread and post a photo of a traditional folder for thirty (30) consecutive days. Take part in the christmas pool or a rak type giveaway. Those wanting to say thank you for a rak may also nominate for the santa. Must start a thread showing a photo of at least eight BO tools Start a new thread showing photos of your outdoor cooking Must have a review written in the proper format and posted on the Main Site Start a new thread with photos of camping, including those showing preferred camping equipment Start a new thread and post a photo of a flashlight as part of your EDC Start a new thread and post a picture of fire making kit or fire with a multitool Start a new thread with photos of a Japanese made PST in your collection Start a thread with photos of at least 5 different Juice models in your collection Start a thread with a photo of at least ten OPT's in your collection

us Offline thatotherguy

  • *
  • Full Member
  • ***
    • Posts: 230
Re: Wave manufacturing date
Reply #12 on: July 24, 2017, 07:32:17 PM
It's from the future. Brought back to current time by aliens. Of course...

us Offline Poncho65

  • Global Moderator
  • *
  • Just Bananas
  • *
    • Posts: 88,456
Re: Wave manufacturing date
Reply #13 on: July 24, 2017, 08:10:19 PM
Quote from: thatotherguy on July 24, 2017, 07:32:17 PM
It's from the future. Brought back to current time by aliens. Of course...
Merit Badges Find him! Post your pocket dump photos then challenge two more members who must post their pocket dump photos within 24hrs for you to get the badge. Must update or add a page on the Multitool.org Multitool Encyclopedia Participate in a Challenge thread, carry a ratcheting tool, and post a photo every day for 30 consecutive days. Participate in a Challenge thread, carry a Leatherman Bond, and post a photo every day for 30 consecutive days. Carry an orange item and post a picture of it everyday for 30 days. Start a thread with a photo of at least ten OPT's in your collection Participate in a challenge by carrying  a Leatherman Pulse or ST200 and post a photo of it  for thirty (30) consecutive days. Start a new thread and post a photo of the Leatherman MiniTool for thirty (30) consecutive days. In this challenge,  carry one(1) Pliers-based or Non-pliers multitool that we always have prejudice against, hate or even fear and post a picture everyday for 30 days Using EDC items randomly selected with a poker hand, post a photo of your EDC or a component of the EDC that got used during the course of the day for 4 weeks (or 30 consecutive days) In the spirit of the Batman utility belt. A 30 day challenge were you have to have at least 2 things clipped to your belt (preferably more). Start a thread and post a picture of your clipped gear each day for 30 days. Participate  in a Challenge thread and post a photo of a Leatherman Skeletool for thirty (30) consecutive days. Only for the 14th year Anniversary Challenge. Post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. You have one of your pictures in the 2020 calendar or in top three of the calendar poll in any month of the given year. Participate  in a Challenge thread and post a photo of a LM Pocket Survival Tool for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Start a new thread and post a photo of the LM Crunch  Multitool for fifteen (15) consecutive days. Start a new thread and post a photo of the keychain for thirty (30) consecutive days. Start a new thread and post a photo of the multitool for thirty (30) consecutive days. You have one of your pictures in the 2018 calendar or in top three of the calendar poll in any month of the given year.

ie Offline Don Pablo

  • *
  • Zombie Apprentice
  • ********
    • Posts: 15,329
  • Yoo-hoo, big summer blowout!
Re: Wave manufacturing date
Reply #14 on: July 24, 2017, 08:14:34 PM
Its never aliens in the same way that X never ever marks the spot.  :doh:
Hooked, like everyone else. ;)

All hail the hook!
Merit Badges Start a new thread and post a photo of the pen for thirty (30) consecutive days. Participate in a Challenge thread and post a photo of  a Bladeless Multitool for 30 days Only for the 14th year Anniversary Challenge. Post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Start a new thread and post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Start a new thread and post a photo of the modified sak (scale swap not included) for thirty (30) consecutive days.

us Offline thatotherguy

  • *
  • Full Member
  • ***
    • Posts: 230
Re: Wave manufacturing date
Reply #15 on: July 24, 2017, 08:31:55 PM
Quote from: Poncho65 on July 24, 2017, 08:10:19 PM
Quote from: thatotherguy on July 24, 2017, 07:32:17 PM
It's from the future. Brought back to current time by aliens. Of course...
(Image removed from quote.)
That is precisely what I was going for.

us Offline Antonio_s2

  • Newbie
  • *
    • Posts: 17
Re: Wave manufacturing date
Reply #16 on: July 24, 2017, 09:57:45 PM
Haha. Doesn't really bother me just thought it be cool to know when my tool was born. There then that it works great! Build quality doesn't seem as good as my juice as far as the finish on the steels and such, but it's great!
"It's not what you take when you leave this world behind you, it's what you leave behind you when you go" - Randy Travis

us Offline aluminated

  • *
  • Sr. Member
  • ****
    • Posts: 286
Wave manufacturing date
Reply #17 on: July 25, 2017, 12:07:00 AM
Find this location in the Wave handle, either side, and you'll find the date code. Use a small flashlight.

This one is an 0117
Merit Badges Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Must start a thread showing a photo of at least three BO tools

us Offline Antonio_s2

  • Newbie
  • *
    • Posts: 17
Re: Wave manufacturing date
Reply #18 on: July 25, 2017, 12:31:56 AM
Quote from: aluminated on July 25, 2017, 12:07:00 AM
Find this location in the Wave handle, either side, and you'll find the date code. Use a small flashlight.
(Image removed from quote.)
This one is an 0117

Exactly where I've been looking. The handle with the can opener says 41917 and the side with the scissors says 41817
"It's not what you take when you leave this world behind you, it's what you leave behind you when you go" - Randy Travis

us Offline Aloha

  • Global Moderator
  • *
  • Point Of No Return
  • *
    • Posts: 31,235
Re: Wave manufacturing date
Reply #19 on: July 25, 2017, 12:34:35 AM
 :oops:

I got nothing . 
Esse Quam Videri
Merit Badges Start a new thread and post a photo of the pen for thirty (30) consecutive days. Start a new thread and post a photo of a traditional folder for thirty (30) consecutive days. Take part in the christmas pool or a rak type giveaway. Those wanting to say thank you for a rak may also nominate for the santa. Must start a thread showing a photo of at least eight BO tools Start a new thread showing photos of your outdoor cooking Must have a review written in the proper format and posted on the Main Site Start a new thread with photos of camping, including those showing preferred camping equipment Start a new thread and post a photo of a flashlight as part of your EDC Start a new thread and post a picture of fire making kit or fire with a multitool Start a new thread with photos of a Japanese made PST in your collection Start a thread with photos of at least 5 different Juice models in your collection Start a thread with a photo of at least ten OPT's in your collection

us Offline aluminated

  • *
  • Sr. Member
  • ****
    • Posts: 286
Wave manufacturing date
Reply #20 on: July 25, 2017, 12:50:27 AM
Aliens. Definitely aliens.
Send it to me and I'll find the date code. You didn't want it back, did you? lol
« Last Edit: July 25, 2017, 12:51:56 AM by aluminated »
Merit Badges Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Must start a thread showing a photo of at least three BO tools

us Offline Antonio_s2

  • Newbie
  • *
    • Posts: 17
Re: Wave manufacturing date
Reply #21 on: July 25, 2017, 01:29:11 AM
Quote from: aluminated on July 25, 2017, 12:50:27 AM
Aliens. Definitely aliens.
Send it to me and I'll find the date code. You didn't want it back, did you? lol

Haha I'll give it to you in exchange of free gas and no bills for 30yrs
"It's not what you take when you leave this world behind you, it's what you leave behind you when you go" - Randy Travis

us Offline aluminated

  • *
  • Sr. Member
  • ****
    • Posts: 286
Re: Wave manufacturing date
Reply #22 on: July 25, 2017, 04:19:38 AM
That should be no problem. I've been giving my wife free gas for almost that long. She's not very appreciative though.
Merit Badges Start a new thread and post a photo of the multitool for thirty (30) consecutive days. Must start a thread showing a photo of at least three BO tools

nz Offline zoidberg

  • Point Of No Return
  • **********
    • Posts: 37,929
Re: Wave manufacturing date
Reply #23 on: July 25, 2017, 11:12:21 AM
So that's no pic then?

ie Offline Don Pablo

  • *
  • Zombie Apprentice
  • ********
    • Posts: 15,329
  • Yoo-hoo, big summer blowout!
Re: Wave manufacturing date
Reply #24 on: July 25, 2017, 01:07:28 PM
Quote from: aluminated on July 25, 2017, 04:19:38 AM
That should be no problem. I've been giving my wife free gas for almost that long. She's not very appreciative though.
:ahhh
Hooked, like everyone else. ;)

All hail the hook!
Merit Badges Start a new thread and post a photo of the pen for thirty (30) consecutive days. Participate in a Challenge thread and post a photo of  a Bladeless Multitool for 30 days Only for the 14th year Anniversary Challenge. Post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Start a new thread and post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Start a new thread and post a photo of the modified sak (scale swap not included) for thirty (30) consecutive days.

Pages: 1   Go Up
 

Donations
Operational Funds

Help us keep the Unworkable working!
Donate with PayPal!
April Goal: $300.00
Due Date: Apr 30
Total Receipts: $115.65
PayPal Fees: $7.03
Net Balance: $108.62
Below Goal: $191.38
Site Currency: USD
36% 
April Donations

Community Links
Multitool.org
Multitool Gallery
Multitool Encyclopedia
SAKWiki
Swiss Army Knights

Powered by EzPortal