Multitool.org Forum
+-

Hello Lurker! Remove this ad and much more by logging in.


93mm awl: how to fit in a 91mm

Raphael Vilamiu · 12 · 1113
« previous next »
Pages: 1   Go Down

Offline Raphael Vilamiu

  • Newbie
  • *
    • Posts: 14
93mm awl: how to fit in a 91mm
on: October 06, 2024, 10:16:14 AM
I saw many times people using the inline awl from the 93mm in their custom 91mm, replacing the small blade.

I measured the awl to be 0.4mm thicker than the blade, which seems to show I need to thin either the awl (1.8mm) or the spacer (1mm) by this amount.

I made a try with the spacer and it got clear that I can't figure out how to do it by myself for lack of skills with tools. And I think thinning the awl would be better, since the spacer would have only 0.6mm in the end.

TL;DR: I'm too dumb to find a way to thin the awl. Can anyone point me out to instructions on how to do it?

us Offline lazar

  • *
  • *
  • Hero Member
  • *****
    • Posts: 721
Re: 93mm awl: how to fit in a 91mm
Reply #1 on: October 06, 2024, 01:52:38 PM
I recently fit a 93mm awl into an 84mm.  I thinned it out on a 1x30 belt sander.  Went slow and sanded at different angles to keep it even.  I also shortened it some to fit, peened brass into the pivot hole and drilled new hole with 2.2mm drill bit, and reprofilled  the pivot area. 
Check out my Etsy shop!
https://customsakmods.etsy.com
Merit Badges Start a new thread with photos of at least 5 different Wenger models in your collection Start a new thread with photos of at least 12 SAKs of different frame lengths and/or shapes in your collection. Eg 58mm, 74mm, 84mm regular, 84mm slim, 85mm etc Participate in a Challenge thread, carry a SAK, duct tape, and paperclip, and post a photo every day for 30 consecutive days. ? Find him! Participate in a Challenge thread, carry a Buck knife or tool, and post a photo every day for 30 consecutive days. Must start a thread with a photo of at least three (3) of your watches Start a new thread including a photo of shooting at least two (2) different firearms and at least one (1) photo of target (firearms) Must start a thread with a photo of your birth year SAK Start a new thread and post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Participate  in Challenge thread and post a photo of a Alox SAK for thirty (30) consecutive days. Start a thread with photos of at least five different colored ALOX models in your collection Participate in a Challenge thread and post a photo of  a Leatherman Micra  for 30 days Start a new thread and post a photo of the discontinued sak/mt for thirty (30) consecutive days. Start a new thread and post a photo of the modified sak (scale swap not included) for thirty (30) consecutive days. Start a new thread with a photo of your custom ALOX with scissors Must post a step by step pictorial of a knife or MT Mod, done by you that includes changing the main chassis of the tool in a significant way. By machining, welding or cutting original design to accept new tool loads. Requests will be reviewed. Start a new thread with a photo of a modded knife or multitool with your EDC Must start a thread with a photo of your camo SAK Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Start a new thread with a photo of custom or non standard SAK scales in your collection

Offline Raphael Vilamiu

  • Newbie
  • *
    • Posts: 14
Re: 93mm awl: how to fit in a 91mm
Reply #2 on: October 06, 2024, 03:30:58 PM
Quote from: lazar on October 06, 2024, 01:52:38 PM
I recently fit a 93mm awl into an 84mm.  I thinned it out on a 1x30 belt sander.  Went slow and sanded at different angles to keep it even.  I also shortened it some to fit, peened brass into the pivot hole and drilled new hole with 2.2mm drill bit, and reprofilled  the pivot area.

Thanks for the info. If you didn't have one (I don't), do you figure you could do it in some other way?

us Offline lazar

  • *
  • *
  • Hero Member
  • *****
    • Posts: 721
Re: 93mm awl: how to fit in a 91mm
Reply #3 on: October 06, 2024, 05:59:20 PM
Quote from: Raphael Vilamiu on October 06, 2024, 03:30:58 PM
Thanks for the info. If you didn't have one (I don't), do you figure you could do it in some other way?

Maybe lay some sandpaper down and rub the awl back and forth a few million times.

Or you could do away with the spacer/key ring and find a washer/washers in the appropriate thickness.  I've done this on mods that have multiple blade layers.
Check out my Etsy shop!
https://customsakmods.etsy.com
Merit Badges Start a new thread with photos of at least 5 different Wenger models in your collection Start a new thread with photos of at least 12 SAKs of different frame lengths and/or shapes in your collection. Eg 58mm, 74mm, 84mm regular, 84mm slim, 85mm etc Participate in a Challenge thread, carry a SAK, duct tape, and paperclip, and post a photo every day for 30 consecutive days. ? Find him! Participate in a Challenge thread, carry a Buck knife or tool, and post a photo every day for 30 consecutive days. Must start a thread with a photo of at least three (3) of your watches Start a new thread including a photo of shooting at least two (2) different firearms and at least one (1) photo of target (firearms) Must start a thread with a photo of your birth year SAK Start a new thread and post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Participate  in Challenge thread and post a photo of a Alox SAK for thirty (30) consecutive days. Start a thread with photos of at least five different colored ALOX models in your collection Participate in a Challenge thread and post a photo of  a Leatherman Micra  for 30 days Start a new thread and post a photo of the discontinued sak/mt for thirty (30) consecutive days. Start a new thread and post a photo of the modified sak (scale swap not included) for thirty (30) consecutive days. Start a new thread with a photo of your custom ALOX with scissors Must post a step by step pictorial of a knife or MT Mod, done by you that includes changing the main chassis of the tool in a significant way. By machining, welding or cutting original design to accept new tool loads. Requests will be reviewed. Start a new thread with a photo of a modded knife or multitool with your EDC Must start a thread with a photo of your camo SAK Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Start a new thread with a photo of custom or non standard SAK scales in your collection

Offline Raphael Vilamiu

  • Newbie
  • *
    • Posts: 14
Re: 93mm awl: how to fit in a 91mm
Reply #4 on: October 06, 2024, 10:15:13 PM
Quote from: lazar on October 06, 2024, 05:59:20 PM
Maybe lay some sandpaper down and rub the awl back and forth a few million times.

Or you could do away with the spacer/key ring and find a washer/washers in the appropriate thickness.  I've done this on mods that have multiple blade layers.

Looks like I need more tools 😬
I guess the washer route could work but that's so less elegant...

us Offline lazar

  • *
  • *
  • Hero Member
  • *****
    • Posts: 721
Re: 93mm awl: how to fit in a 91mm
Reply #5 on: October 06, 2024, 11:00:34 PM
Quote from: Raphael Vilamiu on October 06, 2024, 10:15:13 PM
Looks like I need more tools 😬
I guess the washer route could work but that's so less elegant...

Victorinox uses a washer next to the main blade on the Alox Cadets, it's not so bad.
Check out my Etsy shop!
https://customsakmods.etsy.com
Merit Badges Start a new thread with photos of at least 5 different Wenger models in your collection Start a new thread with photos of at least 12 SAKs of different frame lengths and/or shapes in your collection. Eg 58mm, 74mm, 84mm regular, 84mm slim, 85mm etc Participate in a Challenge thread, carry a SAK, duct tape, and paperclip, and post a photo every day for 30 consecutive days. ? Find him! Participate in a Challenge thread, carry a Buck knife or tool, and post a photo every day for 30 consecutive days. Must start a thread with a photo of at least three (3) of your watches Start a new thread including a photo of shooting at least two (2) different firearms and at least one (1) photo of target (firearms) Must start a thread with a photo of your birth year SAK Start a new thread and post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Participate  in Challenge thread and post a photo of a Alox SAK for thirty (30) consecutive days. Start a thread with photos of at least five different colored ALOX models in your collection Participate in a Challenge thread and post a photo of  a Leatherman Micra  for 30 days Start a new thread and post a photo of the discontinued sak/mt for thirty (30) consecutive days. Start a new thread and post a photo of the modified sak (scale swap not included) for thirty (30) consecutive days. Start a new thread with a photo of your custom ALOX with scissors Must post a step by step pictorial of a knife or MT Mod, done by you that includes changing the main chassis of the tool in a significant way. By machining, welding or cutting original design to accept new tool loads. Requests will be reviewed. Start a new thread with a photo of a modded knife or multitool with your EDC Must start a thread with a photo of your camo SAK Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Start a new thread with a photo of custom or non standard SAK scales in your collection

Offline Raphael Vilamiu

  • Newbie
  • *
    • Posts: 14
Re: 93mm awl: how to fit in a 91mm
Reply #6 on: October 07, 2024, 03:13:01 PM
Quote from: lazar on October 06, 2024, 11:00:34 PM
Victorinox uses a washer next to the main blade on the Alox Cadets, it's not so bad.

I went ahead and used washers. I think it works well.
Thanks for the help!

us Offline IMR4198

  • *
  • Absolutely No Life Club
  • *******
    • Posts: 5,538
Re: 93mm awl: how to fit in a 91mm
Reply #7 on: October 07, 2024, 04:55:44 PM
How about a photo, Raphael?  Some others would love to see what you did.  Best wishes.  Gary (IMR)
 :hatsoff:
Merit Badges Start a new thread with photos of at least 5 different Wenger models in your collection Start a new thread and post a photo daily of any SAK 74mm or smaller ( you can switch it up daily ) for thirty (30) consecutive days. Participate  in Challenge thread and post a photo of a Delemont SAK for thirty (30) consecutive days. Complete a 30 day challenge for carrying a different Multi tool each day of the week based on one of the daily carry threads Start a new thread and post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Start a new thread and post a photo of the multitool for fifteen (15) consecutive days. Must start a thread with a photo of your EDC watch Must start new thread with photos of multitools (Magazine/Catalogue type photos) Start a new thread and post a photo of the multitool for seven (7) consecutive days. Participate in a challenge by carrying  a 100mm or 108mm SAK and post a photo of it  for thirty (30) consecutive days. Post your pocket dump photos then challenge two more members who must post their pocket dump photos within 24hrs for you to get the badge. Participate  in Challenge thread and post a photo of a Classic SAK for thirty (30) consecutive days. Participate  in Challenge thread and post a photo of a MiniChamp SAK for thirty (30) consecutive days. Participate in a Challenge thread and post a photo of a tool made in a specific country for thirty (30) consecutive days. Must update or add a page on SAKWiki Participate  in Challenge thread and post a photo of a SAK Soldier for thirty (30) consecutive days.  Carry tools with single functions only. No multi-tools, no multi-layer Swiss Army Knives, no combo one-piece tools and post a photo for thirty (30) consecutive days. Start a new thread with photos of at least 6 SAKs of different frame lengths and/or shapes in your collection. Eg 58mm, 74mm, 84mm regular, 84mm slim, 85mm etc Start a new thread with photos of your Buck knives in use Participate in a Challenge thread and post a photo of a SAK-alike, aka multi-layered, knife-based pocket tools for thirty (30) consecutive days. Participate in a Challenge thread and post a photo of  a Bladeless Multitool for 30 days

us Offline lazar

  • *
  • *
  • Hero Member
  • *****
    • Posts: 721
Re: 93mm awl: how to fit in a 91mm
Reply #8 on: October 07, 2024, 06:27:50 PM
Quote from: Raphael Vilamiu on October 07, 2024, 03:13:01 PM
I went ahead and used washers. I think it works well.
Thanks for the help!

Sweet!  You're welcome

Quote from: IMR4198 on October 07, 2024, 04:55:44 PM
How about a photo, Raphael?  Some others would love to see what you did.  Best wishes.  Gary (IMR)
 :hatsoff:

We definitely need a pic or two!
Check out my Etsy shop!
https://customsakmods.etsy.com
Merit Badges Start a new thread with photos of at least 5 different Wenger models in your collection Start a new thread with photos of at least 12 SAKs of different frame lengths and/or shapes in your collection. Eg 58mm, 74mm, 84mm regular, 84mm slim, 85mm etc Participate in a Challenge thread, carry a SAK, duct tape, and paperclip, and post a photo every day for 30 consecutive days. ? Find him! Participate in a Challenge thread, carry a Buck knife or tool, and post a photo every day for 30 consecutive days. Must start a thread with a photo of at least three (3) of your watches Start a new thread including a photo of shooting at least two (2) different firearms and at least one (1) photo of target (firearms) Must start a thread with a photo of your birth year SAK Start a new thread and post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Participate  in Challenge thread and post a photo of a Alox SAK for thirty (30) consecutive days. Start a thread with photos of at least five different colored ALOX models in your collection Participate in a Challenge thread and post a photo of  a Leatherman Micra  for 30 days Start a new thread and post a photo of the discontinued sak/mt for thirty (30) consecutive days. Start a new thread and post a photo of the modified sak (scale swap not included) for thirty (30) consecutive days. Start a new thread with a photo of your custom ALOX with scissors Must post a step by step pictorial of a knife or MT Mod, done by you that includes changing the main chassis of the tool in a significant way. By machining, welding or cutting original design to accept new tool loads. Requests will be reviewed. Start a new thread with a photo of a modded knife or multitool with your EDC Must start a thread with a photo of your camo SAK Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Start a new thread with a photo of custom or non standard SAK scales in your collection

Offline Raphael Vilamiu

  • Newbie
  • *
    • Posts: 14
Re: 93mm awl: how to fit in a 91mm
Reply #9 on: October 08, 2024, 01:39:04 PM
Sorry for not sending photos before but I was lost with the interface. Here it goes.

Offline Raphael Vilamiu

  • Newbie
  • *
    • Posts: 14
Re: 93mm awl: how to fit in a 91mm
Reply #10 on: October 08, 2024, 01:45:58 PM
I only used one 0.5mm washer for the large blade. It should be 0.4mm but I don't have one. You guys can see the back of the liner is a bit strange. That happened when I tried to put the titanium scales on. They bent the liner. I needed to file the pins rings a bit and then they fit. It's a bit ugly but I don't think it affects in any way.

One day when I have a belt sander, I think I'll open the knife and do it correctly. But I live in a flat and don't have much space so, it won't be so soon.
« Last Edit: October 08, 2024, 02:21:25 PM by Raphael Vilamiu »

us Offline IMR4198

  • *
  • Absolutely No Life Club
  • *******
    • Posts: 5,538
Re: 93mm awl: how to fit in a 91mm
Reply #11 on: October 08, 2024, 01:47:07 PM
So nice.  I saw where the liner flared a little.  I don't think things are meant to be perfect.  Good work.  Best wishes.  G
 :cheers:
Merit Badges Start a new thread with photos of at least 5 different Wenger models in your collection Start a new thread and post a photo daily of any SAK 74mm or smaller ( you can switch it up daily ) for thirty (30) consecutive days. Participate  in Challenge thread and post a photo of a Delemont SAK for thirty (30) consecutive days. Complete a 30 day challenge for carrying a different Multi tool each day of the week based on one of the daily carry threads Start a new thread and post a photo of any gear for thirty (30) consecutive days during the MTo anniversary month. Start a new thread and post a photo of the multitool for fifteen (15) consecutive days. Must start a thread with a photo of your EDC watch Must start new thread with photos of multitools (Magazine/Catalogue type photos) Start a new thread and post a photo of the multitool for seven (7) consecutive days. Participate in a challenge by carrying  a 100mm or 108mm SAK and post a photo of it  for thirty (30) consecutive days. Post your pocket dump photos then challenge two more members who must post their pocket dump photos within 24hrs for you to get the badge. Participate  in Challenge thread and post a photo of a Classic SAK for thirty (30) consecutive days. Participate  in Challenge thread and post a photo of a MiniChamp SAK for thirty (30) consecutive days. Participate in a Challenge thread and post a photo of a tool made in a specific country for thirty (30) consecutive days. Must update or add a page on SAKWiki Participate  in Challenge thread and post a photo of a SAK Soldier for thirty (30) consecutive days.  Carry tools with single functions only. No multi-tools, no multi-layer Swiss Army Knives, no combo one-piece tools and post a photo for thirty (30) consecutive days. Start a new thread with photos of at least 6 SAKs of different frame lengths and/or shapes in your collection. Eg 58mm, 74mm, 84mm regular, 84mm slim, 85mm etc Start a new thread with photos of your Buck knives in use Participate in a Challenge thread and post a photo of a SAK-alike, aka multi-layered, knife-based pocket tools for thirty (30) consecutive days. Participate in a Challenge thread and post a photo of  a Bladeless Multitool for 30 days

Pages: 1   Go Up
 

Donations
Operational Funds

Help us keep the Unworkable working!
Donate with PayPal!
April Goal: $300.00
Due Date: Apr 30
Total Receipts: $42.16
PayPal Fees: $2.92
Net Balance: $39.24
Below Goal: $260.76
Site Currency: USD
 13%
April Donations

Community Links
Multitool.org
Multitool Gallery
Multitool Encyclopedia
SAKWiki
Swiss Army Knights

Powered by EzPortal