Anything to do with motorcycles, scooter, etc...
-
What a lovely day for a bike ride today.
A mate and I had a very nice breakfast run this morning. It started off pretty cold (1 degree C) but warmed up by the time we had breakfast. He was on his R65LS and me on the R9T. I recently got it back after some warranty work and had to make sure that all was OK. Happy to report so-far it is. Most of the wind Sydney has had over the last few days died down and skies were pretty blue. All up a smallish day, just a tad over 380 km. Both bikes ran very well, good coffee and good food.
I have a couple of days off next week and will definitely go for another run - pics to follow. :D
Cheers, Pete

-
This is what I got. Sorry for the link to a business.
So far, it has worked excellently, and it is small and portable enough to not take over my garage.
-
+1!

@Greg Jones said:
That's a great lift you're putting together Ws
+1 too, looking forward to seeing it when it's finished.
I also have no centre stand on the Guzzi... but they are available both from the maker themselves and from various aftermarket sources. I'm wondering if it's worth adding one. The Beemer I had had one... it makes some things easier (maintenance, parking in tight spaces) but adds a little weight.

Anyway, this can wait a little. I'm currently busy assembling a small spares and tool kit. It seems motorbike manufacturers are eminently confident no one needs any tools these days, nor spare bulbs, fuses and and spark plugs ::). The only tools in the stock kit are one (1) suspension adjustment key and one (1) fuse extractor thingy

Also, I need to make do with a tiny space only under the saddle. Not sure I'll have space for a tyre repair kit... and this makes selecting the tools a bit difficult as I need to watch their size and weight. I have found some used items in the 'bay which are on their way to me. -
G'Day D_T,
I have a similar problem on the R9T in terms of tools and space.
My basic tool-roll consists of the following:
Leatherman Crunch
1/4" hex bits that cover Torx, Hex and screw drivers
1/4" extension
A few fusesTire repair kit (read emergency get out of jail card :D)
8 CO2 canisters and a double inflator that allows two canisters to inflate at the same time. Remember ALWAYS wear gloves when working with these canisters, they freeze on the the outside whilst inflating. DAMHIK.
String plugs - similar to the ones that were discussed a few pages ago
Glue / tire cement
Plug toolThe tools are all inside an old bank bag that the Mrs stitched up for me. The tire repair kit is in a pencil case. Neither fit under my seat, there is NO space under it, but I always carry a small daybag on a day ride. As part of my daily commute, I don't bother with these. I have road side assist and will use them if required.
I took the suspension C-spanners off the bike, I only adjust the suspension at home where I can write changes down and one usually need a second person to help with the measurement.
I'll post pics over the weekend if you want.
Pete
-
The lift I am making for my bike is normally used for repairing cars
And as it is stored in my workshop it’s taking up a lot of space
This is why I am now making it into a motorbike lift to store and
work on the bike for when I am not using it for repairing cars
And this way I have more space in my workshop
-
@Chako said:
This is what I got. Sorry for the link to a business.So far, it has worked excellently, and it is small and portable enough to not take over my garage.
I have had a look at those lifts but my bike hasn’t got the
frame bars running under the engine so all the
weight would be on the engine when lifting the bike
-
That would not work then.

-
Unfortunately not ???
-
Been busy working on fitting the strengthening
slats to the bottom of the platform outside ones are done


-
I have a similar problem on the R9T in terms of tools and space.
My basic tool-roll consists of the following:
Leatherman Crunch
1/4" hex bits that cover Torx, Hex and screw drivers
1/4" extension
A few fusesTire repair kit (read emergency get out of jail card :D)
8 CO2 canisters and a double inflator that allows two canisters to inflate at the same time. Remember ALWAYS wear gloves when working with these canisters, they freeze on the the outside whilst inflating. DAMHIK.
String plugs - similar to the ones that were discussed a few pages ago
Glue / tire cement
Plug toolThe tools are all inside an old bank bag that the Mrs stitched up for me. The tire repair kit is in a pencil case. Neither fit under my seat, there is NO space under it, but I always carry a small daybag on a day ride. As part of my daily commute, I don't bother with these. I have road side assist and will use them if required.
I took the suspension C-spanners off the bike, I only adjust the suspension at home where I can write changes down and one usually need a second person to help with the measurement.
I'll post pics over the weekend if you want.
Pete
Thanks Pete, yeah some pics of the tyre kit would be nice

I'll post pics of my tool kit when it's complete. Just needed to source short versions of the spanners/keys that would fit on various nut sizes except some of the very large ones (the usual suspects: 3, 4, 5, 8, 10 mm Allen and 8, 10, 13, 17, 21 and 24 hexagonal, then 16mm spark plug tube key), some fuses and light bulbs, then add in a test lamp just in the unlikely case of an electrical fault, and some tie wraps and tape. Hope this will fit crosses fingers.
I'm also tinkering with a small box containing circuitry for some additional lights (LED fog lights) and a hazard warning setup. The bike, strangely enough, did not come with the latter so I'm having to build my own (I hate not having one, probably due to the BMW experience). I'd like this to be a pure plug-in solution which I can remove in case of warranty issues, but the V7 III has a peculiar setup where the indicator flasher is integrated in the ECU behind the clocks and feeds front and rear indicators separately
so I need to "intercept" or tap the original circuit in about 5 different places and string several feet of new wiring from the box with suitable connectors as well as a handlebar switch (of course, this being Germany, the switch must light up when the thing is on)

-
And now I have to work out where to place the
strengthening slats on the inside of the platform



-
Wow...

Word of caution: make sure you account for torsion too (if you haven't already), i.e. the support needs to be stiff not only in bending but also torsion. Longitudinal and transversal braces must be interconnected (not just via the platform). If the bike is going to sit on its side stand at all, you'll also need to strengthen the platform locally.
-
Thanks D_T that is what I am looking at next

I need to put in at least 5 strengthening slats for the width
2 at the ends of the platform and 3 where the platform sits on the lift
The plywood sheet is 18mm thick so it’s pretty
strong especially once the slats have been fitted
-
Mmh... I'd add 2 more on the other sides and interconnect them with the widthwise ones...
-
Most of the strengthening slats sit straight on the lift
apart from the 2 I am fitting to the end of the platform
They are going to be the only ones not supported by
the framework of the lift the main reason I fitted the slats
is to miss the Arms that are on the lift that you use to lift
a car up on I will try and take a pic of the lift without the
plywood platform on it so you can see what I am talking about
-
now I am fitting the strengthening slats for the width of the plywood platform
The only problem I have now is I have run out of screws
and I need one more slat of wood for the ends of the platform :ahhh

-
oh I see, both dimensions are covered 
-
Here is a pic of the lift I have
you can see the arms that I am on about
That’s why I am using the wooden
slats to place the plywood platform on
And using the lift to run the strengthening slats on

-
Nice piece of kit

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login