Anything to do with motorcycles, scooter, etc...
-
@Chako said:
This is what I got. Sorry for the link to a business.So far, it has worked excellently, and it is small and portable enough to not take over my garage.
I have had a look at those lifts but my bike hasn’t got the
frame bars running under the engine so all the
weight would be on the engine when lifting the bike
-
That would not work then.

-
Unfortunately not ???
-
Been busy working on fitting the strengthening
slats to the bottom of the platform outside ones are done


-
I have a similar problem on the R9T in terms of tools and space.
My basic tool-roll consists of the following:
Leatherman Crunch
1/4" hex bits that cover Torx, Hex and screw drivers
1/4" extension
A few fusesTire repair kit (read emergency get out of jail card :D)
8 CO2 canisters and a double inflator that allows two canisters to inflate at the same time. Remember ALWAYS wear gloves when working with these canisters, they freeze on the the outside whilst inflating. DAMHIK.
String plugs - similar to the ones that were discussed a few pages ago
Glue / tire cement
Plug toolThe tools are all inside an old bank bag that the Mrs stitched up for me. The tire repair kit is in a pencil case. Neither fit under my seat, there is NO space under it, but I always carry a small daybag on a day ride. As part of my daily commute, I don't bother with these. I have road side assist and will use them if required.
I took the suspension C-spanners off the bike, I only adjust the suspension at home where I can write changes down and one usually need a second person to help with the measurement.
I'll post pics over the weekend if you want.
Pete
Thanks Pete, yeah some pics of the tyre kit would be nice

I'll post pics of my tool kit when it's complete. Just needed to source short versions of the spanners/keys that would fit on various nut sizes except some of the very large ones (the usual suspects: 3, 4, 5, 8, 10 mm Allen and 8, 10, 13, 17, 21 and 24 hexagonal, then 16mm spark plug tube key), some fuses and light bulbs, then add in a test lamp just in the unlikely case of an electrical fault, and some tie wraps and tape. Hope this will fit crosses fingers.
I'm also tinkering with a small box containing circuitry for some additional lights (LED fog lights) and a hazard warning setup. The bike, strangely enough, did not come with the latter so I'm having to build my own (I hate not having one, probably due to the BMW experience). I'd like this to be a pure plug-in solution which I can remove in case of warranty issues, but the V7 III has a peculiar setup where the indicator flasher is integrated in the ECU behind the clocks and feeds front and rear indicators separately
so I need to "intercept" or tap the original circuit in about 5 different places and string several feet of new wiring from the box with suitable connectors as well as a handlebar switch (of course, this being Germany, the switch must light up when the thing is on)

-
And now I have to work out where to place the
strengthening slats on the inside of the platform



-
Wow...

Word of caution: make sure you account for torsion too (if you haven't already), i.e. the support needs to be stiff not only in bending but also torsion. Longitudinal and transversal braces must be interconnected (not just via the platform). If the bike is going to sit on its side stand at all, you'll also need to strengthen the platform locally.
-
Thanks D_T that is what I am looking at next

I need to put in at least 5 strengthening slats for the width
2 at the ends of the platform and 3 where the platform sits on the lift
The plywood sheet is 18mm thick so it’s pretty
strong especially once the slats have been fitted
-
Mmh... I'd add 2 more on the other sides and interconnect them with the widthwise ones...
-
Most of the strengthening slats sit straight on the lift
apart from the 2 I am fitting to the end of the platform
They are going to be the only ones not supported by
the framework of the lift the main reason I fitted the slats
is to miss the Arms that are on the lift that you use to lift
a car up on I will try and take a pic of the lift without the
plywood platform on it so you can see what I am talking about
-
now I am fitting the strengthening slats for the width of the plywood platform
The only problem I have now is I have run out of screws
and I need one more slat of wood for the ends of the platform :ahhh

-
oh I see, both dimensions are covered 
-
Here is a pic of the lift I have
you can see the arms that I am on about
That’s why I am using the wooden
slats to place the plywood platform on
And using the lift to run the strengthening slats on

-
Nice piece of kit

-
Thanks D_T I it’s a very handy tool to have
And I was lucky to get it for a very cheap price
-
Just got back from the wood supplier
And got one more slat of wood size 34x34mm x 2400mm
same size I have been using and one that is the size
of 63x34mm x 2400mm as I am going to use that
one for the two ends of the platform for extra strength
And I bought more screws as I have run out
-
Fitting the last couple of strengthening slats today
Apart from the one that is going to be near the wheel chock
As I have to wait until I got it so I can see where
I got to drill the holes to fasten the wheel chock
And how I am going to mount it to the platform


-
Then I still have to think about making a ramp for the platform
And what type of flooring I am going to use to cover the platform
And what colour I am going to paint the platform :ahhh -
:ahhh
Decisions, decisions

Meanwhile before and after pics of the tool kit on the Guzzi. I have added a few useful items. The filled pouch (minus the spark plug box, that goes into a small rear bag where I keep spare bulbs, a FAK and gloves) still just fits under the seat. Note to self: add some wire, paracord and tie wraps as well as a T40 bit and handle and what I think is a T60 bit.


-
Nice selection of tools for your bike D_T

I have the same for my bike under the rear seat
But I also have a small air compressor
and tyre puncture repair kit under the seat
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login