Charge ALX vs Wave (post2004)
-
Here's mine from about a year or so ago. It's more beat up now. :D

-
Close up of the jaws:

-
Did you use your poor pliers to short a circuit? More importantly, was it intentional?

-
Great side-by-side comparison Jason!

One other important point for those considering buying one of these tools new; the Charge models come with the accessory bits, bit holder, pocket clip, and lanyard ring, whereas with the Wave model these items must be purchased seperately.

-
Well i've been using my Charge since July nonstop daily at work. A few things i have noticed about the Charge ...
It doesn't close as smoothly as my wave- the pliers get stuck/caught sometimes when closing on its self.
The 154CM blade does retain an edge a lot better than the wave- but it chips more. My wave is smooth yet dull after tons of use-the Charge would still cut but i could see very small chips in the edge of the blade. After a few swipes on Lansky it was good as new. The wave takes a bit longer to sharpen up.
The black finish holds up very well. After sliding it back and forth all night to other team members on a smooth concrete floor it dusted off no worse for the wear.
The hook/serrated blade is prob the best tool on it. So many uses besides its intended job. I use it quite a bit to grab the end of a fishtape in the wall. Cut electrical tape off cat5.
About another 6 months i should have the leather sheath broken in to a softness like my ole wave sheath. ;)
-
@Pacu said:
Well i've been using my Charge since July nonstop daily at work. A few things i have noticed about the Charge ...It doesn't close as smoothly as my wave- the pliers get stuck/caught sometimes when closing on its self.
The 154CM blade does retain an edge a lot better than the wave- but it chips more. My wave is smooth yet dull after tons of use-the Charge would still cut but i could see very small chips in the edge of the blade. After a few swipes on Lansky it was good as new. The wave takes a bit longer to sharpen up.
The black finish holds up very well. After sliding it back and forth all night to other team members on a smooth concrete floor it dusted off no worse for the wear.
The hook/serrated blade is prob the best tool on it. So many uses besides its intended job. I use it quite a bit to grab the end of a fishtape in the wall. Cut electrical tape off cat5.
About another 6 months i should have the leather sheath broken in to a softness like my ole wave sheath. ;)
This closely parallels my feelings about the Charge ALX. That guthook is an awesome tool. Glad you like it.
:)
-
Personally I'd rather have scissors than a hook, and I don't like the crimper in the ALX pliers.. which is why I own the AL! :D
I am surprised you don't feel more difference in use. I had the Wave and sold it. Cut some wood with it and your in for some serious pain. The Charge ergonomics are a big improvement, and by far the largest and most important difference between the Wave and the Charge in my view.
I'm not a fan of the TTi either. I think the Wave has the perfect set up.. which is why the Ti and AL are my favourite.
-
at first i didn't care for the crimpers but after installing 34 speaker horns over 3 weeks in the ceiling at work i'm glad they were there.
-
@kinskibrain said:
Personally I'd rather have scissors than a hook, and I don't like the crimper in the ALX pliers.. which is why I own the AL! :DI am surprised you don't feel more difference in use. I had the Wave and sold it. Cut some wood with it and your in for some serious pain. The Charge ergonomics are a big improvement, and by far the largest and most important difference between the Wave and the Charge in my view.
I'm not a fan of the TTi either. I think the Wave has the perfect set up.. which is why the Ti and AL are my favourite.
So this begs the question: "What can you use the cap crimper for?"
Well, my #1 use for the cap crimper opening is pulling R clips and cotter pins, so that they aren't damaged. If Leathermans came with the option of a standard blunt nose (like the old Gerber MultiPliers), this wouldn't be critical, but with the long needlenose plier tip, the standard jaws are too far back to use for pulling clips.
-
@Mr. Whippy said:
Personally I'd rather have scissors than a hook, and I don't like the crimper in the ALX pliers.. which is why I own the AL! :D
I am surprised you don't feel more difference in use. I had the Wave and sold it. Cut some wood with it and your in for some serious pain. The Charge ergonomics are a big improvement, and by far the largest and most important difference between the Wave and the Charge in my view.
I'm not a fan of the TTi either. I think the Wave has the perfect set up.. which is why the Ti and AL are my favourite.
So this begs the question: "What can you use the cap crimper for?"
Well, my #1 use for the cap crimper opening is pulling R clips and cotter pins, so that they aren't damaged. If Leathermans came with the option of a standard blunt nose (like the old Gerber MultiPliers), this wouldn't be critical, but with the long needlenose plier tip, the standard jaws are too far back to use for pulling clips.
why don't you just use a Crunch then
;) :D -
@Mr. Whippy said:
Personally I'd rather have scissors than a hook, and I don't like the crimper in the ALX pliers.. which is why I own the AL! :D
I am surprised you don't feel more difference in use. I had the Wave and sold it. Cut some wood with it and your in for some serious pain. The Charge ergonomics are a big improvement, and by far the largest and most important difference between the Wave and the Charge in my view.
I'm not a fan of the TTi either. I think the Wave has the perfect set up.. which is why the Ti and AL are my favourite.
So this begs the question: "What can you use the cap crimper for?"
Well, my #1 use for the cap crimper opening is pulling R clips and cotter pins, so that they aren't damaged. If Leathermans came with the option of a standard blunt nose (like the old Gerber MultiPliers), this wouldn't be critical, but with the long needlenose plier tip, the standard jaws are too far back to use for pulling clips.
why don't you just use a Crunch then
;) :DWell now, that's the start of another thread... >:D
Needless to say... :D
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login



