Multitool.org Forum
+-

Hello Lurker! Remove this ad and much more by logging in.


Gerber Suspension question

Mr Biriyani · 4 · 1392
« previous next »
Pages: 1   Go Down

se Offline Mr Biriyani

  • Hero Member
  • *****
    • Posts: 603
Gerber Suspension question
on: May 05, 2013, 11:39:41 AM
A qustion to you more experienced repairers. The spring to the scissors on my Suspension tends to go over like this. The spring is slitghtly bend in the wrong direction.
Can I take it out and bend it back or will it likely break ?
Merit Badges Start a new thread with a photo of at least 5 different Charge models in your collection Must start a thread showing a photo of at least eight BO tools Start a new thread showing photos of at least 3 different sporks in use Start a new thread and post a photo of a flashlight as part of your EDC Start a thread with photos of at least 8 different Juice models in your collection Start a thread with photos of at least 5 different MP600 models in your collection Must start new thread with photos of multitools (Magazine/Catalogue type photos)

scotland Offline Gareth

  • Admin Team
  • Point Of No Return
  • *
    • Posts: 37,691
Re: Gerber Suspension question
Reply #1 on: May 05, 2013, 11:50:46 AM
I'd be tempted to try and bend it back myself.  Go gently and don't smash it with a big hammer and you should be OK I think. ;)
Be excellent to each other and always know where your towel is.
Merit Badges Participate  in Challenge thread and post a photo of a Delemont SAK for thirty (30) consecutive days. Must start a thread with a photo of your birth year SAK Start a new thread and post a photo of the minimal sak (2 layers or fewer) for thirty (30) consecutive days. Start a new thread with a photo showing the axe in use Start a new thread and post a photo of a traditional folder for thirty (30) consecutive days. Start a new thread including a photo of shooting at least two (2) different airguns and at least one (1) photo of target (airguns) Must have a review written in the proper format and posted on the Main Site Must post a step by step pictorial of a knife or multitool modification (scale swap not included) Participate in a Challenge thread and post a photo of  a Case knife  for 30 days Participate  in a Challenge thread and post a photo of a LM Pocket Survival Tool for thirty (30) consecutive days.  Post a pic for Halloween of your pumpkin (or turnip or gourd or whatever you traditionally carve for Halloween!) being carved by any SAK, multitool, pocket or woods knife you may own!  Only available once a year Start a new thread with a photo of your custom ALOX with scissors Start a new thread and post a photo of a flashlight as part of your EDC Start a new thread showing photos of your outdoor cooking Start a new thread with a photo of a modded knife or multitool with your EDC Start a new thread with photos of camping, including those showing preferred camping equipment Start a new thread with a photo of custom or non standard SAK scales in your collection

ca Offline Grant Lamontagne

  • Head Turd Polisher
  • Administrator
  • *
  • Just Bananas
  • *
    • Posts: 68,962
  • Optimum instrumentum est inter aures
Re: Gerber Suspension question
Reply #2 on: May 05, 2013, 11:52:19 AM
There is a chance it will break, but then, if it's non-functional otherwise, it might be worth a shot as you really don't have much to lose.

Gerber's warranty service should look after it either as is, or if it gets broken, so it might be worth contacting their representative in your area.

Def
Listen to the Official Podcast of Multitool.org:

It's The Podcast You Never Knew You Needed brought to you by The Only Forum That Matters!
Merit Badges Take part in the christmas pool or a rak type giveaway. Those wanting to say thank you for a rak may also nominate for the santa. For those who posted like a boss. Post your pocket dump photos then challenge two more members who must post their pocket dump photos within 24hrs for you to get the badge. Start a new thread with a photo of custom or non standard SAK scales in your collection Start a thread with a photo of a repair you made with duct tape Start a new thread including a photo of shooting at least two (2) different airguns and at least one (1) photo of target (airguns) Start a thread with a photo of at least ten OPT's in your collection Must start a thread with a photo of at least five (5) of your watches Must start a thread showing a photo of at least eight BO tools Start a thread with photos of at least 1 MTO branded tool in your collection Start a new thread showing photos of your outdoor cooking Must have a review written in the proper format and posted on the Main Site Start a new thread with a photo of at least 5 different Charge models in your collection

se Offline Mr Biriyani

  • Hero Member
  • *****
    • Posts: 603
Re: Gerber Suspension question
Reply #3 on: May 05, 2013, 03:38:49 PM
Thanks guys for the responds !
I did try and it worked. :)
Otherwise I have a history of breaking things I`m trying to bend.
Merit Badges Start a new thread with a photo of at least 5 different Charge models in your collection Must start a thread showing a photo of at least eight BO tools Start a new thread showing photos of at least 3 different sporks in use Start a new thread and post a photo of a flashlight as part of your EDC Start a thread with photos of at least 8 different Juice models in your collection Start a thread with photos of at least 5 different MP600 models in your collection Must start new thread with photos of multitools (Magazine/Catalogue type photos)

Pages: 1   Go Up
 

Donations
Operational Funds

Help us keep the Unworkable working!
Donate with PayPal!
April Goal: $300.00
Due Date: Apr 30
Total Receipts: $70.65
PayPal Fees: $4.43
Net Balance: $66.22
Below Goal: $233.78
Site Currency: USD
22% 
April Donations

Community Links
Multitool.org
Multitool Gallery
Multitool Encyclopedia
SAKWiki
Swiss Army Knights

Powered by EzPortal