Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Newbie modding SAKs

Scheduled Pinned Locked Moved The Mod Squad
117 Posts 1 Posters 17.5k Views
  1. Home
  2. The Mod Squad
  3. Newbie modding SAKs
Newbie modding SAKs
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • m47mu74nt Offline
    m47mu74nt
    Posts: 2,523
    m47mu74nt Offline
    m47mu74nt
    wrote on last edited by
    #12 Quote Reply

      Part one (bis)
      Local retailer doesn't have ANY 2.0mm bras rod :rant: :rant: :rant:

      So... let's investigate the anodization part a little more.
      As said before i'm using lemon juice as acid solution (i doesn't even have white vinegar at home) until i get some H2SO4.

      Interesting fact is that with my setup the color depends of 3 parameters: Volts, Time, Surface
      i'm using 3 PSU savaged from random stuff:

      • a computer ATX PSU ==> 12V
      • an epson printer PSU ==> 40V
      • an old VHS recorder PSU ==> lots of strange voltages available including 34, 48 (wiring the +34V and the - 14V) and 57V (wiring +34V and -23V). It also needs a dummy load to correctly outputs enough current (a computer fan plugged between +12V and gnd is enough)

      Making some dots with and brush connected to the - give the following results:
      From left to right: 40V waiting from 3 to 15 seconds per dots, the longer the contact the more blue.

      With the titanium plate [slightly shorter and wider than a Vic Classic scale] in the water+lemon solution (maximum surface area)
      Sand paper (grit 320) between two tests to remove the oxide formed on the surface. (as expected, the higher the voltage the thicker the oxide and the harder the removal)

      12V, 5 minutes : dark bronze

      34V, 5 minutes : deep violet

      You may notice there is no picture at 40V since the Epson printer PSU cannot give enough current when the contact surface is that big...

      48V, 5 minutes : deep blue-violet

      57V, 5 minutes : blue with some violet

      57V, 10 minutes : light blue

      it is quite interesting to see that when the PSU start the current is about 160mA @57V, and then it decreases to 10mA after 1minutes.

      A 'painted' lightsaber and some shading test:

      Meet me also on youtube & instagram for mostly knives (and multitools) content

      Merit Badges
      Scale Changer Hacker Mod User SAKWiki User Duct Tape BO Tools Level 3 Flashlight Paracord Carabiner User Discontinued SAK/MT Challenge Minimal SAK Challenge Titanium Camo SAK Stayglow SAK Zip Tie User Scaler User Birth Year SAK Hook User ALOX with Scissors MTO Tool MTo Store User Jack'O Lantern Badge ALOX Colors Level 3 Victorinox Spirit Challenge Toothpick User Tool Box Challenge  30 Day Vintage SAK Challenge 30 Day Rhymes with Orange Challenge MTo Anniversary Challenge LM Signal Challenge Wenger Collector Level 3 30 Day Ratchet Challenge MacGyver 30 Day Challenge 20th Anniversary Anything Goes Challenge
      1 Reply Last reply
      • Sparky415 Offline
        Sparky415
        Posts: 13,000
        Sparky415 Offline
        Sparky415
        wrote on last edited by
        #13 Quote Reply

          Interesting stuff M

          Everything’s adjustable

          1 Reply Last reply
          • sLaughterMed Offline
            sLaughterMed
            Posts: 3,450
            sLaughterMed Offline
            sLaughterMed
            wrote on last edited by
            #14 Quote Reply

              @Sparky415 said:
              Interesting stuff M

              +1

              Laughter is the best Medicine
              Slaughter is just Laughter with an "S"

              We are looking for Multitool Encyclopedia Editors! If you are interested, please give me a PM!

              The Multitool Encyclopedia Editing for Dummies Page: http://forum.multitool.org/index.php/topic,65751.0.html
              Multitool Encyclopedia Suggested Edits Page: http://forum.multitool.org/index.php/topic,65746.0.html

              Merit Badges
              SAKWiki User SOG Power Challenge Hacker Multitool Encyclopedia User EDC Pocket Dump Challenge BO Tools Level 2 Santa Ignore MP600 Collector
              1 Reply Last reply
              • SteveC Online
                SteveC
                Global Moderators
                Posts: 72,322
                SteveC Online
                SteveC
                Global Moderators
                wrote on last edited by
                #15 Quote Reply

                  Very cool :tu:

                  Merit Badges
                  Fishing Mod User Hacker Photographer Fire Making BO Tools Level 3 Discontinued SAK/MT Challenge Traditional Folder Challenge MTo Anniversary Challenge Victorinox Spirit Challenge MTO Rotation Challenge Calendar 2019 Calendar  2018 Calendar   2017 LM Surge Challenge Level 2 The SUPER Challenge GEC Challenge LM Crunch 15 day Challenge Chili Award PST 30 Day Challenge Buck User Calendar 2020 Buck 112 Ranger 30 Day Challenge 30 Blades 30 Days Mr Pinchy Love Bites 14th Anniversary Anything Goes Challenge Buck 110 Challenge LM Rebar Challenge The 30 Day MiniTool Challenge 30 Day Locks Up Challenge 20th Anniversary Anything Goes Challenge 30 Day Barlow Challenge
                  1 Reply Last reply
                  • m47mu74nt Offline
                    m47mu74nt
                    Posts: 2,523
                    m47mu74nt Offline
                    m47mu74nt
                    wrote on last edited by
                    #16 Quote Reply

                      With the angle grinder out for a while, the scale making project is on hold :facepalm: :rant:

                      In the mean time, here is a new Ti experiment:
                      Heating (flame) with some Salt crystals (table salt) held in place my wetting the Ti plate before applying the salt. Heat gives the bronze color, the salt crystals create the blue dots on the surface

                      heat-salt-Ti.jpg

                      Meet me also on youtube & instagram for mostly knives (and multitools) content

                      Merit Badges
                      Scale Changer Hacker Mod User SAKWiki User Duct Tape BO Tools Level 3 Flashlight Paracord Carabiner User Discontinued SAK/MT Challenge Minimal SAK Challenge Titanium Camo SAK Stayglow SAK Zip Tie User Scaler User Birth Year SAK Hook User ALOX with Scissors MTO Tool MTo Store User Jack'O Lantern Badge ALOX Colors Level 3 Victorinox Spirit Challenge Toothpick User Tool Box Challenge  30 Day Vintage SAK Challenge 30 Day Rhymes with Orange Challenge MTo Anniversary Challenge LM Signal Challenge Wenger Collector Level 3 30 Day Ratchet Challenge MacGyver 30 Day Challenge 20th Anniversary Anything Goes Challenge
                      1 Reply Last reply
                      • m47mu74nt Offline
                        m47mu74nt
                        Posts: 2,523
                        m47mu74nt Offline
                        m47mu74nt
                        wrote on last edited by
                        #17 Quote Reply

                          Part two : drilling and cutting the Ti scales (Classic and Sentry)

                          Pre-drilling through liners :
                          (No, this is not a drill press, but a hand drill on a stand)

                          NB: applying double sided tape long before working is not a good idea, i had some pain to remove the liners without ruining them :facepalm:

                          Drilling done:

                          Time to cut the scales out of the Ti plate: Titanium screams while being cut by the hacksaw...

                          Testing Alignment:

                          Blank testing the Sentry:

                          End of this part for now, still lacks the angle grinder to continue the scales :)
                          *Next is a texture test on Ti that i'm doing right now.
                          *

                          Meet me also on youtube & instagram for mostly knives (and multitools) content

                          Merit Badges
                          Scale Changer Hacker Mod User SAKWiki User Duct Tape BO Tools Level 3 Flashlight Paracord Carabiner User Discontinued SAK/MT Challenge Minimal SAK Challenge Titanium Camo SAK Stayglow SAK Zip Tie User Scaler User Birth Year SAK Hook User ALOX with Scissors MTO Tool MTo Store User Jack'O Lantern Badge ALOX Colors Level 3 Victorinox Spirit Challenge Toothpick User Tool Box Challenge  30 Day Vintage SAK Challenge 30 Day Rhymes with Orange Challenge MTo Anniversary Challenge LM Signal Challenge Wenger Collector Level 3 30 Day Ratchet Challenge MacGyver 30 Day Challenge 20th Anniversary Anything Goes Challenge
                          1 Reply Last reply
                          • m47mu74nt Offline
                            m47mu74nt
                            Posts: 2,523
                            m47mu74nt Offline
                            m47mu74nt
                            wrote on last edited by
                            #18 Quote Reply

                              I hope this step by step WIP isn't too boring, if so, don't worry this is the last part!

                              Part 3: grinding, anodizing, assembling
                              As the angle grinder is back, that's time to shape the scales: grind grind grind

                              Sanding the scale border held together to get an even surface:

                              After sanding a few steps are left before anodizing : drilling bevels in the rivet holes to ease the peening process, breaking the angles on the scale borders
                              and for fun, 3 dead holes to get textured anodizing

                              Anodizing result (step by step of that bi-color and shading process may come later if needed.):
                              Light blue holes : 57V, lemon juice
                              Shading : 34V, lemon juice

                              Blank testing (yeah, i should have done that before... at that point the spring is a little recessed behind the scales on the back. Let's say "it's not a bug, it's an undocumented feature"
                              Note the gold anodized inside

                              Cutting rivets:

                              Shorting rivets with a file, using a small plastic sheet to protect the Ti scales:

                              No pic during peening process, only two hands here :P

                              And the result:
                              Sadly the pics does not render the real colors here.
                              The dots face has the following pattern : light blue dots and scale with violet shading slowly into bronze
                              The other face is blue>violet>bronze>gold

                              Conclusion: :climber: (this gif has far too much tools to represent my build :facepalm:

                              This build is far from 'professional grade' work (lots of small defects that i could have anticipated... and fixed?) but i think that on the overall it worths the time i spent :)
                              This build really lacks the Swiss cross, that i can't do without a milling machine (but it would look great with the bi-color anodized dead holes)
                              What do you think? should i continue this way or did i made horrible mistakes that i shouldn't do ever again?

                              Meet me also on youtube & instagram for mostly knives (and multitools) content

                              Merit Badges
                              Scale Changer Hacker Mod User SAKWiki User Duct Tape BO Tools Level 3 Flashlight Paracord Carabiner User Discontinued SAK/MT Challenge Minimal SAK Challenge Titanium Camo SAK Stayglow SAK Zip Tie User Scaler User Birth Year SAK Hook User ALOX with Scissors MTO Tool MTo Store User Jack'O Lantern Badge ALOX Colors Level 3 Victorinox Spirit Challenge Toothpick User Tool Box Challenge  30 Day Vintage SAK Challenge 30 Day Rhymes with Orange Challenge MTo Anniversary Challenge LM Signal Challenge Wenger Collector Level 3 30 Day Ratchet Challenge MacGyver 30 Day Challenge 20th Anniversary Anything Goes Challenge
                              1 Reply Last reply
                              • Huntsman Offline
                                Huntsman
                                Global Moderators
                                Posts: 5,781
                                Huntsman Offline
                                Huntsman
                                Global Moderators
                                wrote on last edited by
                                #19 Quote Reply

                                  @m47mu74nt said:
                                  I hope this step by step WIP isn't too boring, if so, don't worry this is the last part!

                                  What do you think? should i continue this way or did i made horrible mistakes that i shouldn't do ever again?

                                  Step by step: **definitely not ** boring - makes it better and very interesting
                                  And all the annodising stuff is fascinating :tu:

                                  Result looks great to me

                                  Re quality/mistakes - I can't really see any - so I'd say continue
                                  I guess if you are going to sell on, then you need to correct the mistakes, if there are any

                                  Great work and thanks for the posts

                                  Merit Badges
                                  Scale Changer OCD Squad Duct Tape Japanese PST Flashlight ALOX Colors Level 2 BO Tools Level 1 Birth Year SAK SAKWiki User Hacker EDC Pocket Dump Challenge ALOX with Scissors MTO Tool MTo Store User Santa
                                  1 Reply Last reply
                                  • m47mu74nt Offline
                                    m47mu74nt
                                    Posts: 2,523
                                    m47mu74nt Offline
                                    m47mu74nt
                                    wrote on last edited by
                                    #20 Quote Reply

                                      @Huntsman said:

                                      @m47mu74nt said:

                                      I hope this step by step WIP isn't too boring, if so, don't worry this is the last part!

                                      What do you think? should i continue this way or did i made horrible mistakes that i shouldn't do ever again?

                                      Step by step: **definitely not ** boring - makes it better and very interesting
                                      And all the annodising stuff is fascinating :tu:

                                      Result looks great to me

                                      Re quality/mistakes - I can't really see any - so I'd say continue
                                      I guess if you are going to sell on, then you need to correct the mistakes, if there are any

                                      Great work and thanks for the posts

                                      Thank you for your feedback :-)
                                      Bad pictures help not to show flaws :whistle:
                                      BTW I won't sell anything, at most those amateur builds will become gifts for friends

                                      Meet me also on youtube & instagram for mostly knives (and multitools) content

                                      Merit Badges
                                      Scale Changer Hacker Mod User SAKWiki User Duct Tape BO Tools Level 3 Flashlight Paracord Carabiner User Discontinued SAK/MT Challenge Minimal SAK Challenge Titanium Camo SAK Stayglow SAK Zip Tie User Scaler User Birth Year SAK Hook User ALOX with Scissors MTO Tool MTo Store User Jack'O Lantern Badge ALOX Colors Level 3 Victorinox Spirit Challenge Toothpick User Tool Box Challenge  30 Day Vintage SAK Challenge 30 Day Rhymes with Orange Challenge MTo Anniversary Challenge LM Signal Challenge Wenger Collector Level 3 30 Day Ratchet Challenge MacGyver 30 Day Challenge 20th Anniversary Anything Goes Challenge
                                      1 Reply Last reply
                                      • Fortytwo Offline
                                        Fortytwo
                                        Posts: 1,285
                                        Fortytwo Offline
                                        Fortytwo
                                        wrote on last edited by
                                        #21 Quote Reply

                                          @m47mu74nt said:
                                          ...at most those amateur builds will become gifts for friends

                                          Your friends should be happy!

                                          Merit Badges
                                          Scale Changer SOG Power Challenge Fishing Minimal SAK Challenge Victorinox Spirit Challenge Chainsaw User MTo Anniversary Challenge
                                          1 Reply Last reply
                                          • Syph007 Offline
                                            Syph007
                                            Global Moderators
                                            Posts: 9,842
                                            Syph007 Offline
                                            Syph007
                                            Global Moderators
                                            wrote on last edited by
                                            #22 Quote Reply

                                              Good stuff! I like when people do progress pics, its nice to see how people work and step by steps are much more interesting then just posting the final build. In fact many successful blade makers started off and gained popularity specificly because they showed how they do their work. It draws in an audience.

                                              Some things I thought while reading.

                                              The liners are the best templates as you discovered. I use little clamps to hold them on the material then scribe lines around and remove. I used double sides tape before too.. annoying. :D

                                              I didnt realize how much Ti-6-4 hardens when heated so if you are using any method to cut them that involves heat, drill holes first. This really caught me off guard when I made the fold over clip on the mini champ. It was impossible to tap the holes in that scale after it was heated to fold.

                                              I grind/sand my scales in fully assembled knife mode to get them exactly flush with the backspring. I dont use the 'good' parts that will be in the final build, just junker old ones. Its the only way I can get the perfectly flush.

                                              Keep up the great work!

                                              PM me or email sakmodder [at] gmail . com if you are looking for custom SAK work.

                                              Modding thread : Here
                                              Website : WWW.SAKModder.com
                                              Facebook : SAKModder
                                              Instagram : robertjlessard
                                              Youtube : www.youtube.com/robertjlessard

                                              1 Reply Last reply
                                              • Boaz Offline
                                                Boaz
                                                Posts: 316
                                                Boaz Offline
                                                Boaz
                                                wrote on last edited by
                                                #23 Quote Reply

                                                  Thanks for sharing, I love to see this sort of project. I think this one looked very nice, I like the 'dead hole' details, it adds a little something. Nice work [emoji1]

                                                  Merit Badges
                                                  Flashlight Time Lord Level 3 Axe User
                                                  1 Reply Last reply
                                                  • m47mu74nt Offline
                                                    m47mu74nt
                                                    Posts: 2,523
                                                    m47mu74nt Offline
                                                    m47mu74nt
                                                    wrote on last edited by
                                                    #24 Quote Reply

                                                      @Fortytwo said:
                                                      Your friends should be happy!

                                                      I hope so :)

                                                      @Syph007 said:
                                                      Good stuff! I like when people do progress pics, its nice to see how people work and step by steps are much more interesting then just posting the final build. In fact many successful blade makers started off and gained popularity specificly because they showed how they do their work. It draws in an audience.

                                                      thank you, the issue with WIP is that it's difficult to both think about taking pictures and building, at least for newbies :D

                                                      @Syph007 said:
                                                      Some things I thought while reading.

                                                      The liners are the best templates as you discovered. I use little clamps to hold them on the material then scribe lines around and remove. I used double sides tape before too.. annoying. :D

                                                      hmmm so you don't pre-drill through the liners? as i don't have a good drill press, i need them in place to guide the drill bit :-\

                                                      @Syph007 said:
                                                      I didnt realize how much Ti-6-4 hardens when heated so if you are using any method to cut them that involves heat, drill holes first. This really caught me off guard when I made the fold over clip on the mini champ. It was impossible to tap the holes in that scale after it was heated to fold.

                                                      This explains the behavior i faced when trying to cut Ti with the angle grinder!

                                                      @Syph007 said:
                                                      I grind/sand my scales in fully assembled knife mode to get them exactly flush with the backspring. I dont use the 'good' parts that will be in the final build, just junker old ones. Its the only way I can get the perfectly flush.

                                                      Keep up the great work!

                                                      nice tip! though i can't follow it until i have enough spare parts to make a dummy build dedicated to grinding, for now i already used the two non limited series of SAKs i had.. (the green Classic SD, and that Ecoline Nylon Sentry)

                                                      @Boaz said:
                                                      Thanks for sharing, I love to see this sort of project. I think this one looked very nice, I like the 'dead hole' details, it adds a little something. Nice work [emoji1]

                                                      Here are some better pics: (i've notice with these that my rivets are far from "nice" so i reworked them a little [no pic yet])
                                                      The dead holes aren't perfect either, looks like the old milling cutter (dremel one) i used didn't do it's job [or i failed using it :whistle:]
                                                      This time the color scheme is much closer to reality!

                                                      Meet me also on youtube & instagram for mostly knives (and multitools) content

                                                      Merit Badges
                                                      Scale Changer Hacker Mod User SAKWiki User Duct Tape BO Tools Level 3 Flashlight Paracord Carabiner User Discontinued SAK/MT Challenge Minimal SAK Challenge Titanium Camo SAK Stayglow SAK Zip Tie User Scaler User Birth Year SAK Hook User ALOX with Scissors MTO Tool MTo Store User Jack'O Lantern Badge ALOX Colors Level 3 Victorinox Spirit Challenge Toothpick User Tool Box Challenge  30 Day Vintage SAK Challenge 30 Day Rhymes with Orange Challenge MTo Anniversary Challenge LM Signal Challenge Wenger Collector Level 3 30 Day Ratchet Challenge MacGyver 30 Day Challenge 20th Anniversary Anything Goes Challenge
                                                      1 Reply Last reply
                                                      • Syph007 Offline
                                                        Syph007
                                                        Global Moderators
                                                        Posts: 9,842
                                                        Syph007 Offline
                                                        Syph007
                                                        Global Moderators
                                                        wrote on last edited by
                                                        #25 Quote Reply

                                                          @m47mu74nt said:

                                                          @Syph007 said:

                                                          Some things I thought while reading.

                                                          The liners are the best templates as you discovered. I use little clamps to hold them on the material then scribe lines around and remove. I used double sides tape before too.. annoying. :D

                                                          hmmm so you don't pre-drill through the liners? as i don't have a good drill press, i need them in place to guide the drill bit :-\

                                                          Oh yes I do use the liners as drilling templates too. But I actually take 4-5 liners rivetted together for that purpose so its a nice thick stack. I use this to drill that hidden 4th hole in all the 91mm Ti scales I do.

                                                          PM me or email sakmodder [at] gmail . com if you are looking for custom SAK work.

                                                          Modding thread : Here
                                                          Website : WWW.SAKModder.com
                                                          Facebook : SAKModder
                                                          Instagram : robertjlessard
                                                          Youtube : www.youtube.com/robertjlessard

                                                          1 Reply Last reply
                                                          • m47mu74nt Offline
                                                            m47mu74nt
                                                            Posts: 2,523
                                                            m47mu74nt Offline
                                                            m47mu74nt
                                                            wrote on last edited by
                                                            #26 Quote Reply

                                                              @Syph007 said:
                                                              Oh yes I do use the liners as drilling templates too. But I actually take 4-5 liners rivetted together for that purpose so its a nice thick stack. I use this to drill that hidden 4th hole in all the 91mm Ti scales I do.

                                                              Is there any thing i should really know before messing with a 91mm? i'd like to make one for a friend's birthday, but before failing i need some advices: is that much more complicated than a Classic?
                                                              i've already found that peening the 84mm rivets (used 2.0mm brass rod) is slightly more complicated than the 1.5mm i used for the Classic. Plus i'm a little worried about the back tools...

                                                              On another subject i'm preparing a post about my process of bi-color anodizing, if anybody wants to make colored recessed swiss cross in their Ti builds that could help :) (it is not a revolution, but it's quite different from what i've read before starting)

                                                              Meet me also on youtube & instagram for mostly knives (and multitools) content

                                                              Merit Badges
                                                              Scale Changer Hacker Mod User SAKWiki User Duct Tape BO Tools Level 3 Flashlight Paracord Carabiner User Discontinued SAK/MT Challenge Minimal SAK Challenge Titanium Camo SAK Stayglow SAK Zip Tie User Scaler User Birth Year SAK Hook User ALOX with Scissors MTO Tool MTo Store User Jack'O Lantern Badge ALOX Colors Level 3 Victorinox Spirit Challenge Toothpick User Tool Box Challenge  30 Day Vintage SAK Challenge 30 Day Rhymes with Orange Challenge MTo Anniversary Challenge LM Signal Challenge Wenger Collector Level 3 30 Day Ratchet Challenge MacGyver 30 Day Challenge 20th Anniversary Anything Goes Challenge
                                                              1 Reply Last reply
                                                              • temo Offline
                                                                temo
                                                                Posts: 639
                                                                temo Offline
                                                                temo
                                                                wrote on last edited by
                                                                #27 Quote Reply

                                                                  I used 2x2.5mm and 2x2mm brass nails. I think 2.5mm on ends were easier. Also I did some errors with tools so had to rebuild my handyman plus. So good to check everything before peening. I would like to know if there would be simple tools and parts to do riverts like vic have (no need for hammering). Looks like pressed.

                                                                  Merit Badges
                                                                  The SUPER Challenge Stargazer Titanium Victorinox Spirit Challenge Mod User Time Lord Level 3 Hacker MTo Anniversary Challenge
                                                                  1 Reply Last reply
                                                                  • Teno Offline
                                                                    Teno
                                                                    Posts: 21
                                                                    Teno Offline
                                                                    Teno
                                                                    wrote on last edited by
                                                                    #28 Quote Reply

                                                                      Very nice work!!!!

                                                                      Marcelo, from Argentina

                                                                      1 Reply Last reply
                                                                      • m47mu74nt Offline
                                                                        m47mu74nt
                                                                        Posts: 2,523
                                                                        m47mu74nt Offline
                                                                        m47mu74nt
                                                                        wrote on last edited by
                                                                        #29 Quote Reply

                                                                          @temo said:
                                                                          I used 2x2.5mm and 2x2mm brass nails. I think 2.5mm on ends were easier. Also I did some errors with tools so had to rebuild my handyman plus. So good to check everything before peening. I would like to know if there would be simple tools and parts to do riverts like vic have (no need for hammering). Looks like pressed.

                                                                          This video gives us a clue :


                                                                          The rivets are friction and press fitted, the tool they use spins and press the rivet end (2min 15sec)

                                                                          Meet me also on youtube & instagram for mostly knives (and multitools) content

                                                                          Merit Badges
                                                                          Scale Changer Hacker Mod User SAKWiki User Duct Tape BO Tools Level 3 Flashlight Paracord Carabiner User Discontinued SAK/MT Challenge Minimal SAK Challenge Titanium Camo SAK Stayglow SAK Zip Tie User Scaler User Birth Year SAK Hook User ALOX with Scissors MTO Tool MTo Store User Jack'O Lantern Badge ALOX Colors Level 3 Victorinox Spirit Challenge Toothpick User Tool Box Challenge  30 Day Vintage SAK Challenge 30 Day Rhymes with Orange Challenge MTo Anniversary Challenge LM Signal Challenge Wenger Collector Level 3 30 Day Ratchet Challenge MacGyver 30 Day Challenge 20th Anniversary Anything Goes Challenge
                                                                          1 Reply Last reply
                                                                          • Sparky415 Offline
                                                                            Sparky415
                                                                            Posts: 13,000
                                                                            Sparky415 Offline
                                                                            Sparky415
                                                                            wrote on last edited by
                                                                            #30 Quote Reply

                                                                              Very nice looking work M :tu:

                                                                              :cheers:

                                                                              Everything’s adjustable

                                                                              1 Reply Last reply
                                                                              • Syph007 Offline
                                                                                Syph007
                                                                                Global Moderators
                                                                                Posts: 9,842
                                                                                Syph007 Offline
                                                                                Syph007
                                                                                Global Moderators
                                                                                wrote on last edited by Syph007
                                                                                #31 Quote Reply

                                                                                  Victorinox uses an orbital rivet machine in that video.

                                                                                  Link Preview Image
                                                                                  Riveting machine - Wikipedia

                                                                                  favicon

                                                                                  (en.wikipedia.org)

                                                                                  PM me or email sakmodder [at] gmail . com if you are looking for custom SAK work.

                                                                                  Modding thread : Here
                                                                                  Website : WWW.SAKModder.com
                                                                                  Facebook : SAKModder
                                                                                  Instagram : robertjlessard
                                                                                  Youtube : www.youtube.com/robertjlessard

                                                                                  1 Reply Last reply

                                                                                  Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                                                  Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                                                  With your input, this post could be even better 💗

                                                                                  Register Login

                                                                                  • 1
                                                                                  • 2
                                                                                  • 3
                                                                                  • 4
                                                                                  • 5
                                                                                  • 6
                                                                                  1. Home
                                                                                  2. The Mod Squad
                                                                                  3. Newbie modding SAKs
                                                                                  Reply
                                                                                  • Reply as topic
                                                                                  Log in to reply
                                                                                  COMMUNITY LINKS
                                                                                  EDC-TV SAKWiki GearFeed SAKSelector
                                                                                  Operational Funds

                                                                                  Help us keep the Unworkable working!

                                                                                  Make A Donation
                                                                                  November Goal: $300.00
                                                                                  Due Date: Nov 30
                                                                                  Total Receipts: $0.00
                                                                                  Below Goal: $300.00
                                                                                  0% funded
                                                                                  • Login

                                                                                  • Don't have an account? Register

                                                                                  • Login or register to search.
                                                                                  • First post
                                                                                    Last post
                                                                                  0