Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Torx head swap mod

Scheduled Pinned Locked Moved The Mod Squad
12 Posts 1 Posters 2.1k Views
  1. Home
  2. The Mod Squad
  3. Torx head swap mod
Torx head swap mod
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • parman53 Offline
    parman53
    Posts: 164
    parman53 Offline
    parman53
    wrote on last edited by
    Quote Reply

      I tried to find info on modding a pioneer with Torx head screws but no luck. I'm sure there must be a thread about how to do it somewhere. I haven't tried a mod yet so this will be my first, is it hard to do?

      Merit Badges
      Flashlight
      1 Reply Last reply
      • BADSAK Offline
        BADSAK
        Posts: 125
        BADSAK Offline
        BADSAK
        wrote on last edited by
        #1 Quote Reply

          I think you will find what you are looking for here:

          /topic/34772

          Merit Badges
          Mod User ALOX with Scissors ALOX Colors Level 2 Flashlight
          1 Reply Last reply
          • parman53 Offline
            parman53
            Posts: 164
            parman53 Offline
            parman53
            wrote on last edited by
            #2 Quote Reply

              @BADSAK said:
              I think you will find what you are looking for here:

              /topic/34772

              That was quick, THANK YOU :salute:

              Merit Badges
              Flashlight
              1 Reply Last reply
              • sLaughterMed Offline
                sLaughterMed
                Posts: 3,450
                sLaughterMed Offline
                sLaughterMed
                wrote on last edited by
                #3 Quote Reply

                  I'm going to start this off by saying that this is absolutely doable at home, but it is a very long and tedious process. It is not for the faint at heart, and if you have never tried this before, I strongly suggest you get a beater Spartan or similarly cheap SAK, and practice first (better to go through a couple dollars worth of SAK and drill bits on something you dont care about, than to ruin a knife you actually like). There's a reason Syph's creations are so expensive.

                  Ideally you would have a drill press for this but it can be done with a hand drill if you are very careful, and use HSS bits.

                  Materials:

                  1. Drill Press (A hand drill can work, but will make this a much more daunting project)

                  2. 1/8" Cobalt or HSS spade drill bits (HSS if using a hand drill) - get multiples in case you break any, or they get dull and you can't resharpen them. If you go HSS I can recommend these from personal experience (im cheap, but they work): http://www.amazon.com/Magnum-Super-Premium-Drill-Pack/dp/B0055WM99I?ie=UTF8&keywords=CTD Magnum Super Premium 1%2F8 Drill Bit (2 Pack)&qid=1462589162&ref_=sr_1_2&sr=8-2

                  3. lubricant (in order of preference -and decreasing cost- cutting fluid, Wd-40, cooking oil)

                  4. coolant (if using cutting fluid, this is also a coolant. water works otherwise)

                  5. Reamer or rotary tool with a jewler's burr

                  6. 1/8" knife pivots (such as these: http://www.amazon.com/Magnum-Super-Premium-Drill-Pack/dp/B0055WM99I?ie=UTF8&keywords=CTD Magnum Super Premium 1%2F8 Drill Bit (2 Pack)&qid=1462589162&ref_=sr_1_2&sr=8-2)

                  7. metal file/metal saw

                  8. Loc-tite

                  Directions:

                  1. Disassemble the SAK. Drill out the rivets, pop off scales. Pull out pins, now you have SAK legos.

                  2. Drill out the springs and tools (save the scales for later). You will want to stop often to cool the work piece with water, to prevent work hardening (which will make drilling out the pivots near impossible). You will want to use enough pressure to see progress being made, ideally you will see a strip of metal being drilled out, but as long as you can tell progress is being made, and the work piece is cooled often, you will be fine. Lubricating the work piece throughout the process will help keep your bit sharp and cutting effectively. Ideally you would use a cutting fluid, but if you don't plan on machining regularly, WD-40 or even olive oil will work as well.

                  3. now that your holes are drilled, you need to clean up and slightly enlarge the holes. Use a reamer in a drill press (easier) or a jeweler's burr in a rotary tool. Ream (or use the burr to cut) out the hole to the correct width (you may still need coolant and lubricant for this). If using a jeweler's burr, make sure to clean up the edges of the hole as well as enlarging the hole. Stop and check the sizing often.

                  4. Now for the scales. using your 1/8" drill bit, drill part way into the backside of the scales. You want to create a place for the pivots to anchor themselves into the scales.

                  5. Test assemble your SAK. You will more than likely need to cut the pivots down to fit in the knife.

                  6. Cut and file the pivots to length. Remember, you want them to be wide enough to stay anchored in your scales, with the pivot fully nested in either scale.

                  7. (optional, only if you did not drill too far into the scale in step 4) Countersink your torx screws. Using a drill bit the size of the torx screw heads, drill slightly into the presentation side of the scale, just enough for the screw to nest into it.

                  8. Test assemble. If all the tools snap correctly, and nothing is too loose, you can disassemble one last time, and use Loc-tite (or other thread locker) to keep the screws from working themselves loose.

                  The first page of Syph007's adventures into Alox (the link BADSAK posted) gives a good visual tutorial for this process.

                  Laughter is the best Medicine
                  Slaughter is just Laughter with an "S"

                  We are looking for Multitool Encyclopedia Editors! If you are interested, please give me a PM!

                  The Multitool Encyclopedia Editing for Dummies Page: http://forum.multitool.org/index.php/topic,65751.0.html
                  Multitool Encyclopedia Suggested Edits Page: http://forum.multitool.org/index.php/topic,65746.0.html

                  Merit Badges
                  SAKWiki User SOG Power Challenge Hacker Multitool Encyclopedia User EDC Pocket Dump Challenge BO Tools Level 2 Santa Ignore MP600 Collector
                  1 Reply Last reply
                  • hiraethus Offline
                    hiraethus
                    Admin Team
                    Posts: 6,969
                    hiraethus Offline
                    hiraethus
                    Admin Team
                    wrote on last edited by
                    #4 Quote Reply

                      Good info sLaughterMed. :tu:

                      I'd add a few points:

                      Use carbide drills if you can get them, especially if you've got access to a drill press. They make drilling the springs and tools so much easier that I feel they're totally worth the extra cost. They are brittle though, so be careful when drilling.

                      Instead of reaming after drilling, you can use a tightly rolled piece of emery or wet and dry paper held in the chuck of your drill as a hone.

                      Buy a countersink tool for recessing the address heads into the scales - much neater than using a drill bit. You might find you only need to recess the centre screw heads. You can also use this for deburring the holes in the tools and scales.

                      Good luck. :tu:

                      Merit Badges
                      Birth Year SAK Mod User Hacker Camping ALOX with Scissors Duct Tape BO Tools Level 1 SAKWiki User ALOX Colors Level 1 Flashlight Traditional Folder Challenge Titanium Santa
                      1 Reply Last reply
                      • windson Offline
                        windson
                        Posts: 616
                        windson Offline
                        windson
                        wrote on last edited by
                        #5 Quote Reply

                          Worth repeating: work slowly and measure OFTEN. You can always take away another tenth of a millimeter, but once it's gone, it's gone.

                          Low Tech Tools, Patches, and Flags from Wndsn Expedition Team | Wndsn Instagram

                          Merit Badges
                          Time Lord Level 1 Hook User ALOX with Scissors Flashlight Stargazer
                          1 Reply Last reply
                          • sLaughterMed Offline
                            sLaughterMed
                            Posts: 3,450
                            sLaughterMed Offline
                            sLaughterMed
                            wrote on last edited by
                            #6 Quote Reply

                              @hiraethus said:
                              Good info sLaughterMed. :tu:

                              I'd add a few points:

                              Use carbide drills if you can get them, especially if you've got access to a drill press. They make drilling the springs and tools so much easier that I feel they're totally worth the extra cost. They are brittle though, so be careful when drilling.

                              Instead of reaming after drilling, you can use a tightly rolled piece of emery or wet and dry paper held in the chuck of your drill as a hone.

                              Buy a countersink tool for recessing the address heads into the scales - much neater than using a drill bit. You might find you only need to recess the centre screw heads. You can also use this for deburring the holes in the tools and scales.

                              Good luck. :tu:

                              Thanks. I had been debating posting something like this for a while, as I could find zero info on the subject of drilling hardend stainless steel anywhere. Even the machining forums were useless; they all knew the differences in drill bits, and what works as a lube or coolant, so no one said it explicitly!

                              Good call on the emery paper, and the countersink tool, im going to use that one.

                              Laughter is the best Medicine
                              Slaughter is just Laughter with an "S"

                              We are looking for Multitool Encyclopedia Editors! If you are interested, please give me a PM!

                              The Multitool Encyclopedia Editing for Dummies Page: http://forum.multitool.org/index.php/topic,65751.0.html
                              Multitool Encyclopedia Suggested Edits Page: http://forum.multitool.org/index.php/topic,65746.0.html

                              Merit Badges
                              SAKWiki User SOG Power Challenge Hacker Multitool Encyclopedia User EDC Pocket Dump Challenge BO Tools Level 2 Santa Ignore MP600 Collector
                              1 Reply Last reply
                              • hiraethus Offline
                                hiraethus
                                Admin Team
                                Posts: 6,969
                                hiraethus Offline
                                hiraethus
                                Admin Team
                                wrote on last edited by
                                #7 Quote Reply

                                  :salute:

                                  A few other things I remembered while I was out this morning:

                                  The Dremel tile cutting bit (#562) is carbide and 1/8" diameter. It's perfect for opening out the holes in the tools.

                                  I deburr the holes in the springs and tools with a conical ceramic grinding bit in my Dremel - a diamond burr would work too.

                                  The countersink tool I use most is a hand held one, rather than one to go in a drill chuck. Works just fine.

                                  Merit Badges
                                  Birth Year SAK Mod User Hacker Camping ALOX with Scissors Duct Tape BO Tools Level 1 SAKWiki User ALOX Colors Level 1 Flashlight Traditional Folder Challenge Titanium Santa
                                  1 Reply Last reply
                                  • parman53 Offline
                                    parman53
                                    Posts: 164
                                    parman53 Offline
                                    parman53
                                    wrote on last edited by
                                    #8 Quote Reply

                                      The reason I decided to go ahead with this is I do have access to a drill press so I know it will make the job easier. I thought I would be able to buy the right length pivots so that's a issue. I have a cheap recruit for my first try.
                                      Thanks guys :tu:

                                      Merit Badges
                                      Flashlight
                                      1 Reply Last reply
                                      • Syph007 Offline
                                        Syph007
                                        Global Moderators
                                        Posts: 9,842
                                        Syph007 Offline
                                        Syph007
                                        Global Moderators
                                        wrote on last edited by
                                        #9 Quote Reply

                                          @hiraethus said:
                                          Good info sLaughterMed. :tu:

                                          I'd add a few points:

                                          Use carbide drills if you can get them, especially if you've got access to a drill press. They make drilling the springs and tools so much easier that I feel they're totally worth the extra cost. They are brittle though, so be careful when drilling.

                                          Instead of reaming after drilling, ** you can use a tightly rolled piece of emery or wet and dry paper held in the chuck of your drill as a hone.**

                                          Buy a countersink tool for recessing the address heads into the scales - much neater than using a drill bit. You might find you only need to recess the centre screw heads. You can also use this for deburring the holes in the tools and scales.

                                          Good luck. :tu:

                                          Its funny, after all these years that is still the method I use. Just on the tool pivot holes though to make sure they are smooth as the holes in the springs dont actually rotate.

                                          PM me or email sakmodder [at] gmail . com if you are looking for custom SAK work.

                                          Modding thread : Here
                                          Website : WWW.SAKModder.com
                                          Facebook : SAKModder
                                          Instagram : robertjlessard
                                          Youtube : www.youtube.com/robertjlessard

                                          1 Reply Last reply
                                          • tattoosteve99 Offline
                                            tattoosteve99
                                            Posts: 6,326
                                            tattoosteve99 Offline
                                            tattoosteve99
                                            wrote on last edited by
                                            #10 Quote Reply

                                              Word of caution. If you use carbide don't use lubricant of it gets hot. It can cause it crack, unless you have a small steady feed. Run the drill press on high speed (rpm) but drill slow.

                                              If I remember correctly, wait, what was I saying?

                                              Merit Badges
                                              EDCSource Buyer Birth Year SAK Flashlight MTO Tool Time Lord Level 1 Paracord Camping ALOX Colors Level 1 EDC Pocket Dump Challenge
                                              1 Reply Last reply
                                              • shibafu Offline
                                                shibafu
                                                Posts: 604
                                                shibafu Offline
                                                shibafu
                                                wrote on last edited by shibafu
                                                #11 Quote Reply

                                                  Rather than drilling out the tools and springs to take 1/8" knife pivots, what about the option of making 3mm and 2.5mm brass pivots by drilling and tapping brass rod? I've had a bit of a play around with making some and it went pretty well, but I haven't tried assembling a SAK with them yet.

                                                  1 Reply Last reply

                                                  Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                  Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                  With your input, this post could be even better 💗

                                                  Register Login

                                                  1. Home
                                                  2. The Mod Squad
                                                  3. Torx head swap mod
                                                  Reply
                                                  • Reply as topic
                                                  Log in to reply
                                                  COMMUNITY LINKS
                                                  EDC-TV SAKWiki GearFeed SAKSelector
                                                  Operational Funds

                                                  Help us keep the Unworkable working!

                                                  Make A Donation
                                                  November Goal: $300.00
                                                  Due Date: Nov 30
                                                  Total Receipts: $0.00
                                                  Below Goal: $300.00
                                                  0% funded
                                                  • Login

                                                  • Don't have an account? Register

                                                  • Login or register to search.
                                                  • First post
                                                    Last post
                                                  0