The Nessmuk Challenge
-
-
Day 18:
Rinaldi wants to go home after some standing block chop practise:

Sent from my iPhone using Tapatalk
-
Day 27

Enjoying a meal with family, can't help but to recruit the Ranger for cutting tasks. :D
-
Day 27:
Needed a new hole in my belt, Rebar to the rescue


Sent fra min FRD-L09 via Tapatalk
-
Sent fra min FRD-L09 via Tapatalk

Mousse is still loose! :D
@ReamerPunch said:
Day 27Third attempt at the bowdrill fire.
I have made some further improvements. Or so I thought.
The bearing block and spindle were a perfect fit, with a nub and hole. This was not ideal. The nub wore away, and the spindle had too much friction against the bearing block. To counter this, I tapered the spindle to fit into a cap nut. It was a little too thin to withstand the pressure, and it snapped after twenty seconds. It had very little friction and I got smoke, so it is not bad. If the cap nut was a little wider, the spindle point would have been more robust.I also scored grooves along the length of the spindle, to make the cord bite into it. My spindle was a polished broom handle, so it was quite smooth. I scraped it with my Mora's spine, but it was still smooth enough not to move some times when pressing down on it and working the bow. Scoring along the length of the spindle helped, but not that much. Spinning made the cord compress the grooves, which made the spindle smooth again. The cord is also not that rough, so I may need to replace that as well.
I put a steel wire loop in the middle of the bow to hold the spindle in place. It makes it easier to get in position without fumbling to get everything together.
The cap nut idea has some merit, so I am not done with it. I have to re-tighten the cord and score the spindle along its length again.

I also found another car seat clip with some seat belt length.


I think Nix's early suggestion of putting some lip stick/lube on top may help? Also, I have seen people wetting their bow string to create more friction, that could be worth a try too.
-
Needed a new hole in my belt, Rebar to the rescue


Sent fra min FRD-L09 via Tapatalk
Nice use, I sometimes use the awl from MT/SAK as a reamer more than the 'awl' function, since I worry they would have created a hole so wide that each subsequent holes maybe too far apart. I wonder do anyone use them for leatherwork or only for emergency repair only.
-
@comis said:
Nice use, I sometimes use the awl from MT/SAK as a reamer more than the 'awl' function, since I worry they would have created a hole so wide that each subsequent holes maybe too far apart. I wonder do anyone use them for leatherwork or only for emergency repair only.Never sewn anything with it, but it makes great holes

Sent fra min FRD-L09 via Tapatalk
-
-
@comis said:
I think Nix's early suggestion of putting some lip stick/lube on top may help? Also, I have seen people wetting their bow string to create more friction, that could be worth a try too.I do not have any lipstick. I could try chapstick.

I had an idea for the bearing block. I tried the cap nut but it's too small, so I'll try one last thing. -
@old Lefty said:
Day 18:
Rinaldi wants to go home after some standing block chop practise:

Sent from my iPhone using Tapatalk
The head on that axe looks amazing.

-
Day 27
Used the Spirit's saw to trim some Saw Palmetto fronds that were sticking out in the driveway and brushing against the car. Victorinox does make some excellent saws. -
Day 27

-
Day 27
-
Day 27:
Gearing up for another adventure..... ;)

-
Day 27 (bonus action....but the knife is missing....
):An upside down Dutch oven, fresh from the oven......

Pulling the cover (bottom) off.....

:o
This is a loaf of what was called "Indian & Rye" bread. This type of bread was more common in the early colonial days in the Americas. Because wheat was expensive and scarce, bread was often made from Rye flour and corn meal (aka "Indian meal").
The Vic FX was used to score the top before baking. I like to bake my crusts to a dark tone for more flavor. The better part of the crust is very white because I dusted the proofing basket heavily with flour and corn meal to prevent it sticking--rye tends to make a sticky dough.
European travelers to the colonies, accustomed to the more refined wheat-based breads of the Europe, often found this colonial bread pitiful and a sign of the hard life of the poor colonials. However, once you get a taste for it, "Indian & Rye" bread is more complex in flavor and wonderfully delicious.
The action was fast and furious, and I didn't pause to get a knife shot after the scoring. (The Dutch oven was screaming hot when I dropped the dough in.)
Another win for the old Dutch oven. John Gould was right!

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login






