Looking for a edc screwdriver
-
As per title
I’m wanting a small compact slim reversible screwdriver with flat and pozi/philips
Doesn’t want it to be ratchet
Just short and slim with a bit/shaft that flips depending what the screw needsI’ve seen the compact wera handle on Amazon and you just put a bit in
But not sure where to keep the other bitsIs there a card you can buy that holds standard 1/4” bits like the one leatherman sells - don’t want leatherman!!
Anyone??
-
Hi Tosh,
For compact daily carry in a shirt or coverall pocket, I carry Klein tools 32511P. It has a reversible shaft that has a pick up magnet on one side and 3.5mm bit holder on the other side. It has a pocket clip to stay keeping it secured in the pocket when not in use. The handle has a carousel that had a good assortment of double sided bits.
In my travel small tool kit I have a Wera compact ratcheting screwdriver 838RAS. I carry bits on Railer rubber bit holders.
JonesE
-
I have an old Stanley with a hollow handle. Put a few bits in the handle and screw on the end. Bits are held on with a magnet of course. I like the screwdrivers with bit storage on board a lot. It is my favorite work bench driver. The only screwdrivers I carry are on a SAK and a one-piece keychain tool. I rarely carry a screwdriver of any sort.
I have seen the Stanley with reversible bits on each end of a removable shaft. It looks okay, but I haven't handled one. Low cost in USA. Maybe $7 or so. I only have one Klein screwdriver, and it is good. Best wishes. G
:D -
If you're working primarily with small screws, the General 744 4-in-1 would be a good option. It has two slotted and two Phillips tips and is very pocketable. They're also inexpensive. Link for informational purposes:
-
If you can live with using 1/4" bits rather than a reversible blade, and if you want to be able to put a decent amount of torque on for a small driver, this pen-sized driver from CountyComm (shown next to a 93mm SAK for scale) is decent:

It's made out of titanium and with the (pretty strong) pocket clip to give you some purchase, you can torque it. The golfball-textured bits are also fairly grippy.
There is storage for three normal sized bits in the handle:

For me if I have one bit in the driver and three stored that covers most stuff I will want to do regularly.
-
Oooh, that’s nice!

JR -
This soft rubber bit rack from Teng Tools is good for carrying some bits around:

Not for pocket carry with all those pointy bits, but good to slip in a small pouch with your driver / SAK / pliers...
-
Milwaukee Fastback
-
Best pocket bit driver I own is the (sadly discontinued) Vic Cybertool S, hands down. Built-in bit storage and bonus Spartan in the handle!
-
There are tons of options. I actually found MTO while looking for an edc screwdriver. :D
I don't have any reversible ones. And I don't know what is slim enough for you. Here are a few I like:Pen drivers: 4mm bits: Strebito, Kershaw (and off brand), 1/4" bits: no brand t-handle driver, probably the best option and the hardest to find.
L drivers: Anex, and tons of no brand ones.
Bike tool sets: Rujoi/PB Swiss with Allen key handle, Sata, FixIt Sticks
Driver handles: PB Swiss, just excellent, 8 standard bits inside, PB Swiss stubby, Wiha stubbyFor bits, you can fit a carabiner on a bit holder, and cut it to size to carry the bits you want. Or get a Railer bit holder. They are deep enough for every hole to hold two bits.
I carry the 711L mini ratchet on my keys with a double bit. This weighs nothing, is short, and clips straight on my keys. The inline driver is great.There are also tons of ratcheting stubbies with on-board bit storage, and some are slim enough for pocket carry, like the Edward Tools blue one.
Pictured: Tone, MichaelPro, Trojan, Edward Tools, Bosch

-
@nate j said:
Best pocket bit driver I own is the (sadly discontinued) Vic Cybertool S, hands down. Built-in bit storage and bonus Spartan in the handle!It is good, but Cybertools are really for precision work, not heavy duty. I managed to break a flathead bit applying too much torque, trying to shift a rusted-in screw. It was stupid on my part, I should have gone to get a proper screwdriver but I was too lazy.
I didn’t realise the S had been discontinued, it’s a shame. I’m glad I have mine. I also have the M, but it is a bit unwieldy - the L must be a real handful. I think the S is definitely better as a driver than the M, it fits the hand better and more importantly, the driver is centred rather than toward one side of the tool, which makes for easier rotation.
-
For compact daily carry in a shirt or coverall pocket, I carry Klein tools 32511P. It has a reversible shaft that has a pick up magnet on one side and 3.5mm bit holder on the other side. It has a pocket clip to stay keeping it secured in the pocket when not in use. The handle has a carousel that had a good assortment of double sided bits.
JonesEI have got this as well and I find it quite good, it lives in a small tool pouch that I take with me on holidays etc.
I generally dislike non-standard bits and kinda wish that Klein had gone for 4mm like everyone else does, so everything would be interchangeable. But with this particular driver it’s not so much of a problem because of the removable blade which has a 1/4” hex section at the magnet end which slots into the handle. That means with a 1/4” to 4mm adapter you can use the handle with your other precision bits. And you can put the blade into some but not all 1/4” bit drivers and so use them with the Klein bits. It needs a driver with a fairly deep socket, like the Wera Rapidaptor, because it has the magnet section below the hex section. Also won’t work with magnet sockets that have the same polarity as the magnet in the blade of course.
-
Thanks for all the replies and links
Much appreciated
Both Knipex and Bahco should be here by Friday
I’ll then see how they feel with a SAK
Need to find a small pouch - sure I have a old tiny canvas camera case, I have a sneaky feeling it will be the right size 🤞
Then depending how much room is spare dictates which screw driver will work best -
I can't help a shameless plug (well it would be if it was actually for sale). For scale, that is MiniChamp.


-
@fullbreakfast said:
It is good, but Cybertools are really for precision work, not heavy duty. I managed to break a flathead bit applying too much torque, trying to shift a rusted-in screw. It was stupid on my part, I should have gone to get a proper screwdriver but I was too lazy.I’ve found mine quite sufficient for pretty much every scenario short of the one you describe, i.e. a seized/rusted in place screw.
That situation would most likely have me pulling out my PWII.

-
I've been watching this with interest, and decided to order one of the Klein drivers. It uses itty bitty bits, BUT, the handle itself takes 1/4" bits. Carries as about 1" in diameter and 5" long.



-
Perhaps the Victorinox L shaped wrench? It is quite handy, take 1\4 inch bits at each end. Kershaw also has a decent multi bit set.
-
@stugumby said:
Perhaps the Victorinox L shaped wrench? It is quite handy, take 1\4 inch bits at each end. Kershaw also has a decent multi bit set.I do actually have that
But it’s in my collection and I don’t actually use any of my collection except a duplicated Explorer I got years ago - grey mag layer.I know it sounds crackers, but if I were to damage or lose anything from the collection I’d have to replace asap.
Hence I never use any of them.
My loft is like a morgue, 700 SAKs & MT’s sat silently in their original boxes/sheaths, never used, never seen.It’s tragic tbh! What a waste
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
